11.180.10 运动用设备及其配合性 标准查询与下载
共找到 711 条与 运动用设备及其配合性 相关的标准，共 48 页
Wheelchairs — Part 22: Set-up procedures
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 4: Energy consumption of electric wheelchairs and scooters for determination of theoretical distance range
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 8: Requirements and test methods for static, impact and fatigue strengths
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 8: Requirements and test methods for static, impact and fatigue strengths
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 14: Power and control systems for electrically powered wheelchairs and scooters — Requirements and test methods
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 22: Set-up procedures
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 4: Energy consumption of electric wheelchairs and scooters for determination of theoretical distance range
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
Wheelchairs — Part 14: Power and control systems for electrically powered wheelchairs and scooters — Requirements and test methods
- ICS
- 11.180.10
- CCS
- 发布
- 2018-08-22
- 实施
1.1 This standard is intended to provide guidance on the evaluation of wear and fatigue characteristics of total disc prostheses under cyclic impingement conditions. 1.2 This guide describes impingement testing of devices with articulating components. The user is cautioned that the methods described herein are intended to produce an impingement condition which may or may not be indicative of clinical performance and which may or may not be consistent with the intended use of the device, and that this should be considered when interpreting the data. Clinically, total disc prostheses should always be implanted per labeling and the manufacturer’s instructions for use. 1.3 Impingement has been observed in retrievals among several total disc prosthesis designs; however, impingement is not necessarily associated with device or clinical failure. It is the intent of this guide to investigate possible impingementinduced wear and mechanical failure modes associated with device design, as well as potential mechanical failure modes associated with clinical events such as subsidence, malpositioning, and improper implant sizing. Note that mechanical failure may or may not be associated with functional failure. 1.4 It is recommended that the user define the bearing and non-bearing features of the intervertebral disc (IVD) prosthesis and evaluate the performance of the IVD prosthesis under Mode 1 wear by using Guide F2423 or ISO 18192-1 prior to use of this guide. This standard is not intended to provide guidance on Mode I testing. 1.5 The goal of this guide is to evaluate impingement in IVD prostheses regardless of the intended region of the spine (cervical or lumbar), material or material combinations (ceramic, metal, polymer), and bearing type (fixed or mobile). 1.6 It is the intent of this guide to enable comparison of IVD prostheses with regard to wear and fatigue characteristics when tested under the specified conditions. 1.7 The values stated in SI units are to be regarded as the standard with the exception of angular measurements which should be reported in degrees. 1.8 The use of this standard may involve the operation of potentially hazardous equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Impingement Testing of Total Disc Prostheses
- ICS
- 11.180.10
- CCS
- 发布
- 2018-07-01
- 实施
Wheelchairs. Determination of maximum speed of electrically powered wheelchairs
- ICS
- 11.180.10
- CCS
- B14
- 发布
- 2018-06-29
- 实施
- 2018-06-29
Wheelchairs－Part 1：Determination of static stability
- ICS
- 11.180.10
- CCS
- 发布
- 2018-06-15
- 实施
Wheelchairs－Part 1：Determination of static stability
- ICS
- 11.180.10
- CCS
- 发布
- 2018-06-15
- 实施
This document specifies test methods for determining the maximum speed of electrically powered wheelchairs, including scooters, intended to carry one person with a maximum nominal speed not exceeding 15 km/h (4,167 m/s) on a level surface.
Wheelchairs - Part 6: Determination of maximum speed of electrically powered wheelchairs
- ICS
- 11.180.10
- CCS
- Y14
- 发布
- 2018-06-01
- 实施
BS ISO 10542-1. Wheelchair tiedown and occupant restraint systems - Part 1. Requirements and test methods for all systems
- ICS
- 11.180.10
- CCS
- 发布
- 2018-04-16
- 实施
- 2018-04-16
Test methods for six-wheel electric wheelchairs
- ICS
- 11.180.10
- CCS
- 发布
- 2018-02-20
- 实施
This document specifies apparatus, test methods and disclosure requirements for wheelchair seat cushions intended to maintain tissue integrity and prevent tissue trauma. Test conditions simulate a symmetric anatomy and posture and do not represent cushion performance for specific individual users. Loads are intended to represent those seen under the pelvis of a 50th percentile wheelchair user and are not intended to assess the weight capacity of the cushion or to characterize the cushion under bariatric loads. It is possible that not all test methods apply to existing and future cushion technologies. It does not include test methods or requirements for determining the fire resistance of cushions. This document can also be applicable to tissue integrity management devices used as other support systems, as well as to cushions used in situations other than a wheelchair.
Wheelchair seating - Part 2: Determination of physical and mechanical characteristics of seat cushions intended to manage tissue integrity
- ICS
- 11.180.10
- CCS
- Y14
- 发布
- 2018-01-01
- 实施
Wheelchair seating — Part 3: Determination of static, impact and repetitive load strengths for postural support devices
- ICS
- 11.180.10
- CCS
- 发布
- 2017-12-29
- 实施
Technical systems and aids for disabled or handicapped persons — Wheelchair tiedown and occupant-restraint systems — Part 1: Requirements and test methods for all systems
- ICS
- 11.180.10
- CCS
- 发布
- 2017-12-29
- 实施
