共找到 235 条与 造口术和失禁用设备 相关的标准,共 16 页
Test methods for skin protection articles for ostomy aids - Part 1: Dimensions, surface pH and water absorption
本文件描述了通过原子吸收光谱法测量钠原子,测定空气粉尘中的聚丙烯酸高吸水粉末含量的方法。采用聚四氟乙烯过滤器和多孔塑料衬垫,在聚苯乙烯-丙烯腈空气监测盒收集聚丙烯酸粉尘试样。 本文件适用于0.2μg~60μg (检测限接近0.
Urine-absorbing aids for incontinence—Measurement of airborne respirable polyacrylate superabsorbent materials—Determination of dust in collection cassettes by sodium atomic absorption spectrometry
本文件描述了造口辅助用皮肤保护用品的耐湿完整性和黏合强度试验方法。 本文件不包含造口辅助用皮肤保护用品的医学特性(细胞毒性、致敏、刺激/皮内反应、缓冲作用、微生物的影响等)。
Skin barrier for ostomy aids—Test methods—Part 2: Wet integrity and adhesive strength
本文件规定了结肠造口护理用的灌洗装置的要求与试验方法。
Aids for ostomy and incontinence—Irrigation sets—Requirements and test methods
GB/T39748 的本部分规定了聚丙烯酸酯(PA)超强吸液粉末可在盐水中萃取的不同链长的羧酸基质量分数的测定方法。这种测试方法用于可萃取聚合物质量分数范围从5.29%到9.
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 10:Determination of extractable polymer content by potentiometric titration
GB/T39748 的本部分规定了聚丙烯酸酯(PA)类超强吸液树脂粉末可吸入颗粒含量的测定方法。 注:商业聚丙烯酸酯类超强吸液树脂粉末颗粒平均直径400μm~800μm,这比直径大约10μm 的可吸入颗粒含量大很多,在生产过程中商业超强吸液树脂粉末只可能出现少量的可吸入颗粒。
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 11:Determination of content of respirable particles
GB39748 的本部分规定了失禁用尿吸收辅助器具所用聚丙烯酸酯超强吸液粉末密度的测定方法。本部分适用于0.67g/mL~0.72g/mL的密度测定(参见附录A),有望适用于较大范围。
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 9:Gravimetric determination of density
GB/T39748 的本部分规定了聚丙烯酸酯(PA)超强吸液粉末的质量流量的测定方法。本部分适用于质量流量在10.62g/s~11.93g/s(参见附录A)范围的材料,有望适用于更大质量流量范围。
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 8:Gravimetric determination of flowrate
GB/T39748 的本部分规定了特定压力下聚丙烯酸酯(PA)超强吸液粉末对盐溶液的吸收量的测定方法。本部分适用于颗粒粒径在45μm 以下不超过0.1%的材料。
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 7:Gravimetric determination of absorption under pressure
GB/T39748 的本部分规定了一种测定聚丙烯酸酯(PA)超强吸液粉末在离心后潴留盐溶液能力的方法。
Urine-absorbing aids for incontinence—Test methods for characterizing polymer-based absorbent materials—Part 6:Gravimetric determination of fluid retention capacity in saline solution after centrifugation
GB/T 17257的本部分定义的术语仅适用于集尿袋的国家标准,相关医学术语不予定义。 本部分的术语无论单独或联合使用,都不作为规定或推荐某种产品的特殊设计、式样和规格。
Urine collection bags.Part 1:Vocabulary
GB/T 17257的本部分规定了下列开口式和闭口式贮尿袋的要求和检验方法。 a)穿在身上的集尿袋(穿着式); b)用挂钩或落地架悬挂的集尿袋(非穿着式)。 本部分不适用于尿道再生手术、女用和儿童用集尿袋。
Urine collection bags.Part 2:Requirements and test methods
本标准规定了抓握杆的要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于居室内各种金属、非金属和复合材料等制成的抓握杆。
Technical aids for persons with disabilities.Grab-rails
GB/T 20407的本部分定义的术语仅适用于造口袋的国家标准,涉及医学术语未予以定义。
Ostomy collection bags. Part 1: Vocabulaty
GB/T 20407的本部分详细说明了对下列一件式和多件式造口袋的要求和测试方法。 a)闭口袋 b)开口袋 c)尿路造口袋
Ostomy collection bags. Part 2: Requirements and test methods
GB/T 20407的本部分规定了结肠造口袋和回肠造口袋异味弥散测定的测试方法。此测试方法适用于联体和分体造口袋,分体造口袋含有封闭式和开放式两种。
Ostomy collection bags. Part 3: Determination of odour transmission of colostomy and ileostomy bags
GB/T 20405的本部分规定了一种交联聚丙烯酸酯(PA)类超强吸液粉末水分含量在0%~5%间的受热失重的测定方法。这种方法可精确到0.1%。 本部分适用于可自由流动的粉末状聚合物超强吸液材料在(15~150)℃间的测试。在这一温度区间挥发的物质,如水,会产生影响。
Urine-absorbing aids for incontinence. Test methods for characterizing Polymer-based absorbent materials. Part 4: Determination of moisture content by mass loss upon heating
GB/T 20405的本部分规定了一种聚丙烯酸酯(PA)类超强吸液粉末中残留丙烯酸纳和丙烯酸单体总量(以丙烯酸计)的测定方法。
Urine-absorbing aids for incontinence. Test methods for characterizing Polymer-based absorbent materials. Part 2: Determination of amount of residual monomers
GB/T 20405的本部分规定了一种交联聚丙烯酸酯(PA)类超强吸液粉末粒径在45µm~850µm分布的测定方法。 本部分适用于可自由流动的粉末状聚合物超强吸液材料在15℃~35℃间的测试。
Urine-absorbing aids for incontinence. Test methods for characterizing Polymer-based absorbent materials. Part 3: Determination of particle size distribution by sieve fractionation
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号