13.340.40 防护手套 标准查询与下载

ASTM E3212-19 执法和矫正人员戴的防护手套的选择和采购的标准指南

1.1 This guide addresses selection and procurement of protective gloves worn by law enforcement and corrections officers. 1.2 This guide explains to end users the content and value of the two below listed standards and how to procure gloves that meet their requirements. 1.2.1 Specification E3109: 1.2.1.1 The purpose of Specification E3109 is to provide performance requirements, performance ratings, and test methods for the evaluation of protective gloves used in law enforcement and corrections applications. 1.2.1.2 Test methods and performance ratings are included to aid glove purchasers and end users in their evaluation of whether a protective glove meets their needs. It is not required that a glove meet every performance requirement specified in this specification. 1.2.2 Practice E3108: 1.2.2.1 Practice E3108 establishes the conformity assessment requirements for protective gloves worn by law enforcement and corrections officers and provides two options for verifying that protective gloves meet requirements: (1) supplier’s declaration of conformity (SDOC) and (2) certification. 1.2.2.2 The practice is intended to be used by purchasers and suppliers in the procurement of gloves that meet Specification E3109, and the purchaser is responsible for selecting either SDOC or certification. 1.3 This guide and the aforementioned standards were developed based on a survey of end users regarding hazards of concern and operational requirements of officers. (See Section 5.) 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection and Procurement of Protective Gloves Worn by Law Enforcement and Corrections

ISO 18889:2019 农药操作人员和重返工作人员用防护手套.性能要求

This document establishes minimum performance, classification, and labelling requirements for gloves worn by operators and re-entry workers handling pesticide products to protect the hands or hands and forearms against contact with those products. Gloves covered by this document include gloves made with elastomeric and polymeric materials in the areas that provide protection. This document does not address protection against fumigants. This document needs to be used in conjunction with ISO 21420.

Protective gloves for pesticide operators and re-entry workers — Performance requirements

T/CTCA 6-2019 劳动防护手套

本标准规定了劳动防护手套的术语和定义、分类、技术要求、试验方法、检验规则、标识、运输和贮存。技术要求包括手套外观、规格尺寸、灵活性、机械防护性能、化学防护性能、不泄漏性能、pH值、六价铬含量、重金属限量、邻苯二甲酸酯增塑剂含量、甲醛含量、异味以及可分解致癌芳香胺的偶氮染料含量。

Labor protective gloves

ISO 10819:2013/Amd 1:2019 机械振动和冲击.手臂振动.手掌手套振动传递率的测量和评估.修改件1

Mechanical vibration and shock — Hand-arm vibration — Measurement and evaluation of the vibration transmissibility of gloves at the palm of the hand — Amendment 1

ISO 23388:2018 机械风险防护手套

This document specifies requirements, test methods, marking and information to be supplied for protective gloves against the mechanical risks of abrasion, blade cut, tear, puncture and, if applicable, impact. This document is intended to be used in conjunction with ISO 21420. The test methods developed in this document can also be applicable to arm protectors.

Protective gloves against mechanical risks

KS K ISO 11393-4:2018 手持链锯用户的防护服 - 第4部分:防护手套的测试方法和性能要求

Protective clothing for users of hand-held chain-saws — Part 4: Test methods and performance requirements for protective gloves

KS K ISO 11393-4-2018 手持链锯用户的防护服 - 第4部分:防护手套的测试方法和性能要求

Protective clothing for users of hand-held chain-saws — Part 4: Test methods and performance requirements for protective gloves

ISO 18639-4:2018 消防员进行专门救援活动的PPE集合 - 第4部分:手套

This document provides the principles that govern the development of incident type and/or hazard specific test methods and minimum performance requirements for protective gloves for firefighters while engaged in specific rescue activities. Gloves related to specific specialist rescue activities, such as road traffic crash (RTC) and urban search and rescue (USAR), are documented in individual subclauses of this document. NOTE Further guidance can be found in ISO 18639-1. The purpose of this document is to ensure that minimum performance requirements for incident type and/or hazard specific protective gloves are designated. This document deals with “rescue from emergencies involving modes of transportation” in particular performance requirements for personal protective equipment (PPE) intended to be used by firefighters, primarily but not solely to protect against hazard exposure at non fire rescue activities involving road traffic crash (RTC) or motor vehicle accidents (MVA). This document covers general glove design, the minimum performance level of the materials used and the methods of test for determining this performance level. This document does not cover special gloves for use in other high risk situations such as firefighting. This document does not cover protection for the head, torso, arms, legs and feet. These are covered in other parts of the ISO 18639 series. It does not cover protection of the hands against other hazards, e.g. chemical, biological, radiation and electrical hazards, except for limited, accidental exposure to fire ground chemicals and blood or body fluids. Selection of the appropriate system of personal protective equipment (PPE), including gloves, is dependent on carrying out an effective risk assessment which identifies the hazard to be faced, evaluates the likelihood of those hazards and provides the means of reducing or eliminating these hazards.

PPE ensembles for firefighters undertaking specific rescue activities — Part 4: Gloves

DIN EN ISO 374-1:2018 防危险化学品和微生物的防护手套 第1部分：化学品风险的术语和性能要求（ISO 374-1:2016 + Amd. 1:2018）；德文版 EN ISO 374-1:2016 + A1:2018

This document is intended to amend DIN EN ISO 374-1. This part of ISO 374 specifies the requirements for protective gloves intended to protect the user against dangerous chemicals and defines terms to be used. If other protection features have to be covered, e. g. mechanical risks, thermal risks, electrostatic dissipation etc., the appropriate specific performance standard is to be used in addition. Further information on protective gloves standards can be found in the EN 420.

Protective gloves against dangerous chemicals and micro-organisms - Part 1: Terminology and performance requirements for chemical risks (ISO 374-1:2016 + Amd. 1:2018); German version EN ISO 374-1:2016 + A1:2018

ISO 11393-4:2018 手持式链锯使用者用防护服装.第4部分:防护手套试验方法和性能要求

This document specifies the performance requirements, test methods, design requirements, identification and marking information for gloves that offer protection against cutting by hand-held chainsaws. Guidance on chainsaw use and the selection of gloves is given in Annex A.

Protective clothing for users of hand-held chainsaws - Part 4: Performance requirements and test methods for protective gloves

EN ISO 374-1:2016/A1:2018 危险化学品和微生物防护手套-第1部分:术语和化学风险性能要求 包含修改件A1,2018

Protective gloves against dangerous chemicals and micro-organisms - Part 1: Terminology and performance requirements for chemical risks - Amendment 1 (ISO 374-1:2016/Amd 1:2018)

ASTM D7329-07(2018) 食品制备和食品处理（食品服务）手套的标准规范

1.1 This specification covers the properties necessary for thin film, unlined polymer gloves to be used in food preparation and food handling. 1.2 This specification is intended to serve as a referee and a guide to permit obtaining gloves of a consistent performance. The safe and proper use of gloves is excluded from the scope of this specification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Food Preparation and Food Handling (Food Service) Gloves

ASTM E3108-18 执法和惩戒人员所戴防护手套合格评定的标准实施规程

1.1 This practice establishes the conformity assessment requirements for protective gloves worn by law enforcement and corrections officers. It was developed based on end user input regarding hazards of concern and operational requirements of officers.2 1.2 This practice provides two options for conformity assessment: (1) supplier’s declaration of conformity (SDOC) and (2) certification. 1.2.1 This practice is intended to be used by purchasers and suppliers in the procurement of gloves that meet Specification E3109, and the purchaser is responsible for selecting either SDOC or certification. NOTE 1—An ASTM guide is being developed to provide agencies and end users with information related to the selection, procurement, and use of protective gloves worn by law enforcement and corrections officers while on duty. 1.2.2 The performance, testing, labeling, documentation, and reporting requirements for SDOC and for certification are specified in Specification E3109. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Conformity Assessment of Protective Gloves Worn by Law Enforcement and Corrections Officers

ASTM E3109-18 执法和惩戒人员戴的防护手套的标准规范

1.1 This specification addresses protective gloves worn by law enforcement and corrections officers. 1.2 This specification and related standards were developed by subject matter experts, including experienced end users, using data from a survey of more than 800 U.S. law enforcement and corrections officers. 1.3 This specification addresses performance requirements, performance ratings, and test methods for whole gloves and for glove components (for example, materials, layers). NOTE 1—This specification references published ASTM standards. 1.3.1 A glove is not uniform in terms of the protection it provides, and different portions or areas of a glove (for example, palm, fingertip) may offer different protection. 1.3.2 It is not intended that a single glove meet all specified performance requirements within this specification. 1.4 The glove supplier will identify which of the performance requirements a specific glove meets and the performance ratings for the different portions or areas of the glove. 1.5 This specification specifies performance requirements for (1) physical protection, including resistance to cut, puncture, and needle stick, and (2) resistance to abrasion and tearing to ensure protection is maintained during use. 1.5.1 A document outlining dexterity and other physical protection requirements identified by end users as important is being developed. 1.6 It is expected that this specification will be used by suppliers, test laboratories, certification bodies, and purchasers. 1.7 It is intended that two related standards be used in conjunction with this specification: 1.7.1 A Guide for Selection, Procurement, and Use of Protective Gloves Worn by Law Enforcement and Corrections, in development by ASTM. 1.7.2 Practice E3108. 1.8 Units—The values stated in SI or CGS2 units are to be regarded as standard. The primary units displayed in this standard are consistent with the referenced ASTM test methods. The values given in parentheses are mathematical conversions that are provided for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Protective Gloves Worn by Law Enforcement and Corrections Officers

DIN EN ISO 374-1/A1:2017 危险化学品和微生物防护手套 第1部分：化学品风险的术语和性能要求 修正案 1（ISO 374-1:2016/DAM 1:2017）

This document is intended to amend DIN EN ISO 374-1. This part of ISO 374 specifies the requirements for protective gloves intended to protect the user against dangerous chemicals and defines terms to be used. If other protection features have to be covered, e. g. mechanical risks, thermal risks, electrostatic dissipation etc., the appropriate specific performance standard is to be used in addition. Further information on protective gloves standards can be found in the EN 420.

Protective gloves against dangerous chemicals and micro-organisms - Part 1: Terminology and performance requirements for chemical risks - Amendment 1 (ISO 374-1:2016/DAM 1:2017); German and English version EN ISO 374-1:2016/prA1:2017

17/30311258 DC BS EN ISO 18889 农药操作人员的防护手套 性能要求

BS EN ISO 18889. Protective gloves for pesticide operators. Performance requirements

T/ZZB 0185-2017 聚氯乙烯防护手套

本标准规定了聚氯乙烯防护手套的基本要求、技术要求、检验方法、检验规则、标识、包装、运输、贮存和质量承诺。 本标准适用于各行业广泛使用的以聚氯乙烯为主体材料制成的有衬里的劳动防护手套（以下简称手套）。

Polyvinyl chloride protective gloves

DIN EN ISO 374-1:2017 防危险化学品和微生物的防护手套.第1部分:化学风险的术语和性能要求(ISO 374-1-2016);德文版本EN ISO 374-1-2016

Protective gloves against dangerous chemicals and micro-organisms - Part 1: Terminology and performance requirements for chemical risks (ISO 374-1:2016); German version EN ISO 374-1:2016

DIN EN ISO 374-5:2017 防危险化学品和微生物的防护手套.第5部分:微生物风险的术语和性能要求(ISO 374-5-2016);德文版本EN ISO 374-5-2016

Protective gloves against dangerous chemicals and micro-organisms - Part 5: Terminology and performance requirements for micro-organisms risks (ISO 374-5:2016); German version EN ISO 374-5:2016

DIN EN 388:2017 防机械危害的手套;德文版本EN 388-2016

Protective gloves against mechanical risks; German version EN 388:2016