17.040.10 极限和配合 标准查询与下载

GB/T 17773-1999 形状和位置公差 延伸公差带及其表示法

本标准规定了延伸公差带的标注原则和图样表示方法。

Tolerancing of orientation and location--Projected tolerance zone

GB/T 8069-1998 功能量规

本标准规定了功能量规的尺寸公差、形位公差和允许磨损量。 本标准适用于检验采用最大实体要求的被测要素和（或）基准要素的功能量规。 当最大实体要求按GB/T 1182、GB/T 4249和GB/T 16671的规定应用于被测要素和（或）基准要素时，功能量规用来确定它们的实际轮廓是否超出相应的边界。

Functional gauges

GB/T 1800.2-1998 极限与配合.基础.第2部分:公差,偏差和配合的基本规定

本标准规定了极限与配合的公差、偏差与配合的代号、表示及解释和配合分类。 本标准适用于圆柱及非圆柱形光滑工件的尺寸。

Limits and fits--Bases--Part 2: Basic rules of tolerances, deviations and fits

GB/T 1800.3-1998 极限与配合.基础.第3部分:标准公差和基本偏差.数值表

本标准规定了极限与配合的标准公差和基本偏差数值表及其由来。应用本极限与配合时，表列数值是权威的。 本标准适用于圆柱及非圆柱形光滑工件的尺寸。

Limits and fits--Bases--Part 3: Numerical values tables of standard toleranes and fundamental deviations

GB/T 16892-1997 形状和位置公差 非刚性零件注法

本标准规定了非刚性零件的形状和位置公差注法。适用于金属薄壁件，挠性材质的零件如橡胶件、塑料件等刚性零件。

Geometrical tolerancing. Indication of non-rigid parts

GB/T 1800.1-1997 极限与配合 基础 第1部分;词汇

本标准确定了极限与配合的基本术语，适用于各技术标准、文件以及科技出版物等。

Limits and fits--Based--Part 1: Terminology

GB/T 1182-1996 形状和位置公差 通则、定义、符号和图样表示法

本标准规定了工件需要的所有形状和位置公差（简称形位公差）的定义，提出了形位公差的基本要求、符号、标注和在图样中的表示方法。 本标准适用于一切工业制品从功能出发的形状和位置公差要求。

Geometrical tolerancing--Generalities, definitions, indications on drawings

GB/T 1184-1996 形状和位置公差未注公差值

本标准主要适用于用去除材料方法形成的要素，也可用于其他方法形成的要素，但使用时应确定本部门的制造精度是否是在本标准规定的未注公差值之内。

Geometrical tolerancing--Geometrical tolerance for features without individual tolerance indications

GB/T 16671-1996 形状和位置公差 最大实体要求、最小实体要求和可逆要求

本标准规定了最大实体要求、最小实体要求和可逆要求的术语、基本规定、图样表示方法及应用示例。 本标准适用于控制零件中心要素的形位公差与其相应的轮廓要素的尺寸公差之间的关系。

Geometrical tolerancing--Maximum material requirement, least material requirement and reciprocity requirement

GB/T 12360-1990 圆锥配合

本标准规定了圆锥配合的形成、术语及定义和一般规定。 本标准适用于锥度C从1：3至1：500，长度工从6至630mm，直径至500mm光滑圆锥的配合。其公差的给定方法，按GB11334一89《圆锥公差》中4.2a条的规定。即：

Cone fit

GB/T 11337-1989 平面度误差检测

本标准规定了平面度误差测量的术语定义、评定方法、测量方法和数据处理方法。 本标准适用于机械工业产品中零件要素的平面度误差测量。 本标准是对GB 1958中平面度误差测量的具体规定。

Measurement of departures from flatness

GB/T 11336-1989 直线度误差检测

本标准规定了直线度误差检测的术语定义、评定方法、检测方法和数据处理方法。 本标准适用于机械工业产品中零件要素的直线度误差检测。 本标准是对GB 1958中直线度误差检测的具体规定。

Measurement of departures from straightness

GB/T 11334-1989 圆锥公差

本标准规定了圆锥公差的项目、给定方法和公差数值。 本标准适用于锥度C从1：3至1：500、圆锥长度L从6至630mm的光滑圆锥。本标准中的圆锥角公差也适用于棱体的角度与斜度。

Cone tolerance

GB/T 5371-1985 公差与配合 过盈配合的计算和选用

本标准适用于光滑圆柱面在弹性范围内的过盈联结计算和过盈配合的选用。

Tolerances and fits--The calculation and selection of interference fits

GB/T 1958-1980 形状和位置公差 检测规定

本标准的检测对象是形状和位置误差（简称形位误差）。

Rules for inspection of form and position tolerances

GSO ISO 14405-2:2024 产品几何技术规范 (GPS) 尺寸公差 第2部分：除线性或角度尺寸以外的尺寸

This document illustrates the ambiguity caused by the use of dimensional specifications to control properties other than linear or angular size and the benefit of using geometrical specifications instead. Dimensional tolerancing can be indicated by ± tolerancing or geometrical specifications. The ambiguity caused by using ± tolerances for dimensions other than linear or angular sizes (for individual tolerances and general tolerances according to, e.g. ISO 2768-1 and ISO 8062-3) is explained in Annex A. NOTE 1 The figures, as shown in this document, merely illustrate the text and are not intended to reflect actual usage. The figures are consequently simplified to indicate only the relevant principles. NOTE 2 For indications of dimensional specifications, see the following: — ISO 14405-1 for linear size; — ISO 14405-3 for angular size; — ISO 2538-1 and ISO 2538-2 for wedges; — ISO 3040 for cones. NOTE 3 The rules for geometrical specifications are given in ISO 1101.

Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear or angular sizes

24/30463912 DC 产品几何规范 (GPS) 尺寸公差 第1部分：线性尺寸

Geometrical product specifications (GPS) — Dimensional tolerancing - Part 1: Linear sizes

ISO 8062-4:2023 产品几何规格 模制零件的尺寸和几何公差 在通用基准系统中使用轮廓公差的铸件的规则和通用公差

This document specifies the rules for geometrical dimensioning and tolerancing of final moulded parts and parts machined out of moulded parts. It also specifies rules and conventions for the indications of these requirements in technical product documentation and specifies the proportions and dimensions of the graphical symbols to be used. This document provides symbols for identifying the relative completeness of the moulded features and parts. These graphical symbols differ from the graphical symbols for surface texture according to This document specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes. This document establishes the general principles for presentation of general geometrical tolerances that apply to 2D technical drawings in all disciplines and trades but which are also applicable to 3D applications. NOTE All figures are shown in 2D views only. When cast datum surfaces are machined, this document is not applicable.

Geometrical product specifications. Dimensional and geometrical tolerances for moulded parts - Rules and general tolerances for castings using profile tolerancing in a general datum system

EN ISO 8062-3:2023 产品几何量技术规范(GPS).模制件尺寸和几何公差.第3部分:铸件一般尺寸,几何公差和机械加工余量

This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes. This document does not apply to 3D CAD models used without indicated dimensions. This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11. The dimensional tolerances covered by this document are tolerances for linear dimensions. The geometrical tolerances covered by this document are tolerances for: — straightness; — flatness; — roundness; — parallelism; — perpendicularity; — symmetry; — coaxiality. This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances. This document can be used for the selection of tolerance values for individual indications.

Geometrical product specifications (GPS) - Dimensional and geometrical tolerances for moulded parts - Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions (ISO 8062-3:2023

ISO 8062-3:2023 产品几何量技术规范(GPS).模制件尺寸和几何公差.第3部分:铸件一般尺寸、几何公差和机械加工余量

Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions