17.040.30 测量仪器仪表 标准查询与下载

GB/T 13823.12-1995 振动与冲击传感器的校准方法 安装在钢块上的无阻尼加速度计共振频率测试

本标准规定了安装在钢块上的无阻尼加速度计共振频率测试的技术要求和测试方法。 本标准适用于质量小于30g，频率范围1～50kHz的无阻尼压电加速度计。

Methods for calibration of vibration and shock pick-ups. Resonance frequency testing of undamped accelerometers on a steel block

GB/T 14324-1993 电容液位计

本标准规定了电容液位计（以下简称仪表）的分类、技术要求、试验方法和检验规则等。 本标准适用于检测各种液体液位的电容液位计，检测两相介质界面或料位的电容物位计也可参照使用。

Electrical capacitance level meter

GB/T 13972-1992 海洋水文观测仪器通用技术条件

本标准规定了水文观测仪器（含设备）的技术要求，工作特性及其表示方法，试验方法，验收规则，标志、包装、运输和贮存要求。和深度的水文观测仪器的研制、生产及制 本标准适用于测定海洋（水）的波浪、水位、流、温度、盐度和订产品标准。

General technical specifications for oceanographic hydrological instruments

GB/T 13925-1992 铸造高锰钢金相

本标准规定了铸造高锰钢在金相显微镜下进行显微组织、晶粒度和非金属夹杂物级别的评定。 本标准适用于GB5680《高锰钢铸件技术条件》中所规定的铸造高锰钢。

Metallographs for high manganese cast steel

GB/T 10922-1989 非螺纹密封的管螺纹量规

本标准规定了非螺纹密封的管螺纹量规的名称、代号、尺寸、公差、检验方法及标志与包装。 本标准适用于检验GB7307《非螺纹密封的管螺纹》所规定的管螺纹。

Gauges for pipe threads where pressure-tight joints are not made on the threads

GB/T 10932-1989 螺纹千分尺

本标准规定了螺纹千分尺的型式、基本参数与尺寸、技术要求、标志与包装以及检验方法。 本标准适用于分度值为0.01mm，测微螺杆螺距为0.5mm，量程为25mm，测量范围至150mm的螺纹千分尺。

Thread micrometers

GB/T 1218-1987 深度千分尺

本标准适用于分度值为0.01mm、测微螺杆螺距为0.5mm和量程为25mm、测量范围至150mm面的深度千分尺。

Depth micrometers

GB/T 8061-1987 杠杆千分尺

本标准适用于测微头的分度值为0.01mm，量程为25mm；指示表的分度值为0.001或0.002mm测量范围至100mm的杠杆千分尺。

Indicating micrometers

GB/T 1217-1986 公法线千分尺

本标准适用于测量模数等于和大于1mm的齿轮的，分度值为0.01mm，测微螺杆螺距为0.5mm和量程为25mm，测量范围至150mm的公法线千分尺。

Gear tooth micrometers

GB/T 6092-1985 90°角尺

本标准适用于检验工件垂直度时所用的90°角尺。

Squares 90 degree

GB/T 6091-1985 刀口形直尺

本标准适用于检验工件直线度所用的刀口形直尺。

Straight edge

GB/T 5106-1985 圆柱直齿渐开线花键量规

本标准适用于检验GB3478.1-83《圆柱直齿渐开线花键（齿侧配合）模数基准齿形公差》中规定的、分度圆直径至180mm工件花键的圆柱直齿渐开线花键量规（以下称“花键量规”）。

Gauges for straight cylindrical involute splines

GB/T 1216-1985 外径千分尺

本标准适用于分度值0.01mm，测微螺杆螺距0.5mm和量程为25mm，测量范围为1000mm的外径千分尺（以下简称“千分尺”）。

Micrometers

GB/T 1957-1981 光滑极限量规

Limit gauges for plain workpiece

GB/T 1581-1979 米制锥螺纹量规

本标准适用于检验GB1415-78《米制锥螺纹》用的量规。

Gauges for tapered screw thread,metric series

GSO ISO 12179:2024 产品几何技术规范 (GPS) 表面纹理：轮廓法 接触式（触针式）仪器的校准

This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 3274. The calibration and adjustment is intended to be carried out with the aid of measurement standards. Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 3274.

Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments

GSO ISO 10360-10:2024 几何产品规范 (GPS) 坐标测量系统 (CMS) 的验收和再验证测试 第10部分：激光跟踪仪

This document specifies the acceptance tests for verifying the performance of a laser tracker by measuring calibrated test lengths, according to the specifications of the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the laser tracker. The acceptance and reverification tests given in this document are applicable to laser trackers utilizing a retroreflector, or a retroreflector in combination with a stylus or optical distance sensor, as a probing system. Laser trackers that use interferometric measurement (IFM), absolute distance measurement (ADM) or both can be verified using this document. This document can also be used to specify and verify the relevant performance tests of other spherical coordinate measurement systems that use cooperative targets, such as “laser radar” systems. NOTE       Systems which do not track the target, such as laser radar systems, will not be tested for probing performance. This document does not explicitly apply to measuring systems that do not use a spherical coordinate system. However, interested parties can apply this document to such systems by mutual agreement. This document specifies: —    performance requirements that can be assigned by the manufacturer or the user of the laser tracker; —    the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements; —    rules for proving comformity; —    applications for which the acceptance and reverification tests can be used.

Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers

GSO ISO 10360-5:2024 几何产品规范 (GPS) 坐标测量系统 (CMS) 的验收和重新验证测试 第5部分：使用离散点和/或的单触针和多触针接触探测系统的坐标测量机 (CMM)……

This document specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using: — any type of contacting probing system; and — spherical or hemispherical stylus tip(s). NOTE CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere. This document applies to CMMs supplied with any of the following: a) single-stylus probing systems; b) multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. "star" stylus); c) multiple probing systems such as those with a stylus for each of their probes; d) systems with articulating probing systems; e) stylus and probe changing systems; f) manual (non-driven) and automated CMMs; g) installations including a scanning probe, capable of being used in a scanning mode. This document is not applicable to non-contacting probing systems, which require different testing procedures. The term ?combined CMM and multi-stylus probing system size error' has been shortened to ?multi-stylus size error' for convenience. This applies in similar cases. If it is desirable to isolate the probing system performance as far as is practical, the influence of the CMM can be minimized but not eliminated. See Annex C for more information.

Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 5: Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and/or...

T/SSC 4-2024 光纤光栅应变仪 通用技术规范

本文件规定了应用于地震领域的光纤光栅应变仪技术要求、测试方法及检验规则。

Fiber-optic grating strainmeter — General technical specifications

T/SDAS 814-2024 荧光法海水中石油类快速监测仪通用技术要求

本文件规定了荧光法海水中石油类快速监测仪（以下简称“监测仪”）的技术要求，试验方法，检验规则，标志、包装、运输和储运等内容。 本文件适用于基于荧光法进行海水和河口水中石油类快速监测仪。

General technical requirements for rapid monitoring instruments for petroleum in seawater using fluorescence method