17.060 体积、质量、密度和粘度的测量 标准查询与下载

ASTM E126-19 ASTM液体比重计的检验 校准和验证的标准测试方法

1.1 This test method describes the principles, apparatus, and procedures for the inspection, calibration, and verification of ASTM glass hydrometers. This test method is applicable to ASTM hydrometers and may be used for other general hydrometers of the constant-mass, variable-displacement type. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The metric equivalents of inch-pound units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Inspection, Calibration, and Verification of ASTM Hydrometers

ASTM D2161-19 运动粘度转换为赛氏通用粘度或赛氏糠醇粘度的标准实施规程

Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity

ASTM F1080-93(2019) 用稠度计测定粘稠液体一致性的标准试验方法

1.1 This test method describes a procedure for the determination of the flow of a standard volume of a semisolid or thick liquid under its own weight. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Consistency of Viscous Liquids Using a Consistometer

ASTM D88/D88M-07(2019)e1 Saybolt粘度的标准测试方法

1.1 This test method covers the empirical procedures for determining the Saybolt Universal or Saybolt Furol viscosities of petroleum products at specified temperatures between 21 and 99°C [70 and 210°F]. A special procedure for waxy products is indicated. NOTE 1—Test Methods D445 and D2170/D2170M are preferred for the determination of kinematic viscosity. They require smaller samples and less time, and provide greater accuracy. Kinematic viscosities may be converted to Saybolt viscosities by use of the tables in Practice D2161. It is recommended that viscosity indexes be calculated from kinematic rather than Saybolt viscosities. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Saybolt Viscosity

ASTM E100-19 ASTM比重计标准规范

1.1 This specification covers glass hydrometers of various scale graduation systems, as required by the ASTM Test Methods in which they are used. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for ASTM Hydrometers

DB13/T 2966-2019 商店超市诚信计量建设规范

Standards for the construction of credit measurement in stores and supermarkets

DB13/T 2962-2019 定量包装商品生产企业诚信计量建设规范

Standards for Integrity Measurement Construction of Quantitative Packaging Commodity Production Enterprises

ASTM C1005-19 用于确定用于液压水泥物理测试的质量和体积的参考质量和设备的标准规范

Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements

ASTM D6703-19 自动Heithaus滴定法的标准测试方法

1.1 This test method describes a procedure for quantifying three Heithaus compatibility parameters that quantify the colloidal stability of asphalts and asphalt cross blends and aged asphalts. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Automated Heithaus Titrimetry

KS B 8300-2018 燃气表 - 转换设备第1部分:体积转换

Gas meters — Conversion devices — Part 1: Volume conversion

KS B 8300-2018(2023) 燃气表转换装置第1部分:体积转换

Gas meters — Conversion devices — Part 1: Volume conversion

ASTM D4052-18a 数字密度计的液体密度 相对密度和API重力的标准测试方法

Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter

ASTM D4486-18 挥发性和活性液体运动粘度的标准试验方法

1.1 This test method covers the measurement of kinematic viscosity of transparent, Newtonian liquids which because of their reactivity, instability, or volatility cannot be used in conventional capillary kinematic viscometers. This test method is applicable up to 2 × 10−5 N/m2 (2 atm) pressure and temperature range from −53 °C to +135 °C (−65 °F to +275 °F). 1.1.1 For the measurement of the kinematic viscosity of other liquids, see Test Method D445. The difference between the two methods is in the viscometers. The viscometers specified in used Specification D446 are open to the atmosphere, while the viscometers in this method are sealed. When volatile liquids are measured in sealed viscometers, the density of the vapor may not be negligible compared with the density of the liquid and the working equation of the viscometer has to account for that. See Section 11 for details. 1.2 WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use Caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.2, 7.3, 7.4, and Annex A1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Kinematic Viscosity of Volatile and Reactive Liquids

ASTM D6172/D6172M-18 用摄影测量程序由操作员直接编译而成的等高线或横截面测定散装材料体积的标准试验方法

1.1 This test method covers procedures concerning site preparation, technical procedures, quality control, and equipment to direct the efforts for determining volumes of bulk material. These procedures include practical and accepted methods of volumetric determination. 1.2 This test method allows for only two volume computation methods. 1.2.1 Contour Test Method—See 8.1.1 and 9.1. 1.2.2 Cross-Section Test Method—See 8.1.2 and 9.2. 1.2.3 This test method requires direct operator compilation for both contours and cross-section development. 1.2.4 The use of Digital Terrain Model software and procedures to create contours or cross sections for volume calculation is NOT encompassed in this test method. NOTE 1—A task group has been established to develop a test method for Digital Terrain Modeling (DTM) procedures. It will address all known data collection procedures such as conventional ground survey, photogrammetry, geodetic positioning satellite (GPS), and so forth. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Volume of Bulk Materials Using Contours or Cross Sections Created by Direct Operator Compilation Using Photogrammetric Procedures

T/EPIAJL 1-2018 水内冷发电机内冷水箱含氢量、内冷水系统漏氢量检测技术规范

内冷水系统含氢量检测装置结构设计及安装、内冷水系统含氢量的判断、内冷水箱及漏氢在线监测装置传感器校验。

Technical specifications for detection of hydrogen content in the inner cooling water tank of water inner cooling generators and hydrogen leakage in the inner cooling water system

ASTM D7496-18 Saybolt Furol粘度计乳化沥青粘度的标准试验方法

1.1 This test method utilizes the Saybolt Furol viscometer to measure the consistency of emulsified asphalt. It is applicable to all the emulsified asphalts specified in Specifications D977 and D2397/D2397M. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in noncompliance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer

T/ZZB 0733-2018 钢制称重传感器

本标准规定了测量质量用钢制称重传感器（以下简称传感器）的术语和定义、产品型式、基本参数和分类、技术要求、试验方法、检验规则以及标志、包装、运输、贮存和质量承诺。 本标准适用于测量静态质量的准确度等级为C级、最大检定分度数为3000～5000的传感器。 与传感器配套使用，并显示质量的仪表，其技术要求由其他相关标准作出规定。

Steel load cells

ASTM D6347/D6347M-05(2018) 使用核反向散射深度密度法测定煤的堆积密度的标准测试方法

1.1 This test method covers procedures for determining the bulk density of coal using instrumentation that measures the relative backscatter of nuclear gamma radiation throughout the depth of the stockpile under test. 1.2 This procedure is applicable to all ranks of coal. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. The equipment uses radioactive materials, which may be hazardous to the health of users, unless proper precautions are taken. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Bulk Density of Coal Using Nuclear Backscatter Depth Density Methods

DIN 51562-1 Berichtigung 1:2018 粘度计 使用 Ubbelohde 粘度计测量运动粘度 第1部分：粘度计规格和测量程序；勘误表 1

The document deals with the measurement procedure of kinematic viscosity with the Ubbelohde viscometer and its design.

Viscometry - Measurement of kinematic viscosity by means of the Ubbelohde viscometer - Part 1: Viscometer specification and measurement procedure; Corrigendum 1

ASTM D5478-13(2018) 通过下降针粘度计测定材料粘度的标准试验方法

1.1 These test methods cover the measurement of the viscosity of Newtonian and non-Newtonian liquids. These test methods are applicable to liquids having viscosities in the range from 5 × 10−4 to 103 Pa·s (0.5 to 106 cP). The shear rate range is dependent upon the needle used and viscosity of the liquid and may vary from 10−4 to 103 s−1 . With an extension bar and applied weight, a shear rate of 104 s–1 may be achieved. 1.2 The yield stress of liquids having this property may also be determined. 1.3 These test methods consist of determining liquid viscosities of Newtonian and non-Newtonian fluids (clear or opaque) by measuring the steady-state (constant) or terminal velocities of cylindrical needles as they fall through the test liquid under the influence of gravity. Yield stresses of nonNewtonian liquids may be measured using the same procedure. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer