17.220.99 有关电学和磁学的其他标准 标准查询与下载

KS C IEC 60763-2-2014(2019) 层压板规范 - 第2部分:试验方法

Specification for laminated pressboard — Part 2: Methods of test

EN 60243-3:2014 绝缘材料的电气强度 试验方法 第3部分：1,2/50 碌s 脉冲试验的附加要求

IEC 60243-3:2013 gives requirements additional to those in IEC 60243-1 for the determination of the electric strength of solid insulating materials under 1,2/50 µs impulse voltage stress. This third edition cancels and replaces the second edition, published in 2001, and constitutes an editorial revision.

Electric strength of insulating materials - Test methods - Part 3: Additional requirements for 1,2/50 µs impulse tests

EN 60243-2:2014 绝缘材料的电气强度 试验方法 第2部分：使用直流电压进行试验的附加要求

IEC 60243-2:2013 gives requirements additional to those in IEC 60243-1 for the determination of the electric strength of solid insulating materials under direct voltage stress. This third edition cancels and replaces the second edition published in 2001, and constitutes an editorial revision.

Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage

GSO IEC 62615:2013 ESD 灵敏度测试 传送路径脉冲 安装（组件）级别

This International Standard defines a method for pulse testing to evaluate the voltage current response of the component under test and to consider protection design parameters for electro-static discharge (ESD) human body model (HBM). This technique is known as transmission line pulse (TLP) testing. This document establishes a methodology for both testing and reporting information associated with transmission line pulse (TLP) testing. The scope and focus of this document pertains to TLP testing techniques of semiconductor components. This document should not become alternative method of HBM test standard such as IEC 60749-26. The purpose of the document is to establish guidelines of TLP methods that allow the extraction of HBM ESD parameters on semiconductor devices. This document provides the standard measurement and procedure for the correct extraction of HBM ESD parameters by using TLP.

Electrostatic discharge sensitivity testing - Transmission line pulse (TLP) - Component level

EN 60243-1:2013 绝缘材料的电气强度 试验方法 第1部分：工频试验

IEC 60243-1:2013 provides test methods for the determination of short-time electric strength of solid insulating materials at power frequencies between 48 Hz and 62 Hz. This standard does not cover the testing of liquids and gases, although these are specified and used as impregnates or surrounding media for the solid insulating materials being tested. NOTE: Methods for the determination of breakdown voltages along the surfaces of solid insulating materials are included.

Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies

DB50/T 495-2013 电能表运行管理规范

本标准规定了贸易结算用电能表运行抽检起始时间及周期、抽样数量、检验项目、判定依据、抽样结果处理几方面的内容。本标准适用于贸易结算用电能表的运行管理。

Electric energy meter operation management specification

GOST R 53734.3.2-2013 静电学. 静电效果的模拟方法. 机械设备的静电放电模型

Electrostatics. Methods for simulation of electrostatic effects. Model of mechanical device electrostatic discharge

LST EN 60684-2-2011 柔性绝缘套管 第2部分：试验方法（IEC 60684-2:2011）

Flexible insulating sleeving -- Part 2: Methods of test (IEC 60684-2:2011)

EN 60666:2010 矿物绝缘油中特定添加剂的检测与测定

IEC 60666:2010 provides methods concerning the detection and determination of specified additives in unused and used mineral insulating oils. The detection methods may be applied to assess whether or not a mineral insulating oil contains an additive as specified by the supplier. The determination methods are used for the quantitative determination of additives known to be present or previously detected by the appropriate detection method. The main changes with respect to the previous edition are listed below: - a change in the title from 'Detection and determination of specified anti-oxidant additives in insulating oils'; - new Annexes B and C which provide methods for the determination of two additives different from the anti-oxidants.

Detection and determination of specified additives in mineral insulating oils

GSO IEC 61340-5-1:2008 静电学 第5部分：保护电子设备免受静电现象的影响一般要求

Applies to activities that: manufacture, process, assemble, install, package, label, service, test, inspect, transport or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges greater than or equal to 100 V human body model (HBM). Provides the requirements for an ESD control program. The user should refer to IEC 61340-5-2 for guidance on the implementation of this standard. Does not apply to electrically initiated explosive devices, flammable liquids, gases and powders. The purpose of this standard is to provide the administrative and technical requirements for establishing, implementing and maintaining an ESD control program (hereinafter referred to as the "program"). The main changes with respect to the previous edition are listed below: This version of IEC 61340-5-1 focuses on the requirements for an ESD control program. In addition, this version of IEC 61340-5-1 has been aligned with other major ESD control program standards used throughout the world.

electrostatics-Part5-1:protection of electonic devices from electostatic phenomena-General requirements

DS/EN 60085:2008 电气绝缘 热评估和命名

This International Standard now distinguishes between thermal classes for electrical insulation systems and electrical insulating materials. It establishes the criteria for evaluating the thermal endurance of either electrical insulating materials (EIM) or electrical insulation systems (EIS). It also establishes the procedure for assigning thermal classes.This standard is applicable where the thermal factor is the dominant ageing factor. NOTE A thermal class is not assigned to an EIM as related to its use in an EIS

Electrical insulation - Thermal evaluation and designation

DS/EN 61340-3-1:2007 静电学 第 3-1 部分：静电效应模拟方法 人体模型（HBM）静电放电测试波形

This part of IEC 61340 describes the discharge current waveforms used to simulate Human Body Model (HBM) ElectroStatic Discharges (ESD) and the basic requirements for equipment used to develop and verify these waveforms.This part of IEC 61340 describes the discharge current waveforms used to simulate human body model (HBM) electrostatic discharges (ESD) and the basic requirements for equipment used to develop and verify these waveforms.This standard covers HBM ESD waveforms for use in general test methods and for application to materials or objects, electronic components and other items for ESD withstand-test or performance-evaluation purposes. The specific

Electrostatics - Part 3-1: Methods for simulation of electrostatic effects - Human body model (HBM) electrostatic discharge test waveforms

DS/EN 61340-3-2:2007 静电学 第 3-2 部分：静电效应模拟方法 机器模型（MM）静电放电测试波形

This part of 61340 describes the discharge current waveforms used to simulate machine model (MM) electrostatic discharges (ESD) and the basic requirements for equipment used to develop and verify these waveforms.This standard covers MM ESD waveforms for use in general test methods and for application to materials or objects, electronic components and other items for ESD withstand test or performance evaluation purposes. The specific application of these MM ESD waveforms to non-powered semiconductor devices is covered in 60749-27.

Electrostatics - Part 3-2: Methods for simulation of electrostatic effects - Machine model (MM) electrostatic discharge test waveforms

BS EN 61340-3-2:2007 静电学.静电效应模拟方法.静电放电试验波机械模型(MM)

This part of IEC 61340 describes the discharge current waveforms used to simulate machine model (MM) electrostatic discharges (ESD) and the basic requirements for equipment used to develop and verify these waveforms. This standard covers MM ESD waveforms for use in general test methods and for application to materials or objects, electronic components and other items for ESD withstand test or performance evaluation purposes. The specific application of these MM ESD waveforms to non-powered semiconductor devices is covered in IEC 60749-27.

Electrostatics - Methods for simulation of electrostatic effects - Machine model (MM) electrostatic discharge test waveforms

EN 60763-2:2007 层压纸板规范 第2部分：测试方法

IEC 60763-2:2007 gives methods of test applicable for the material classified in IEC 60763-1. This edition includes the following significant technical changes with respect to the previous edition: The standard has generally been revised editorially and brought into line with IEC 60641-2; The test method for the determination of the internal ply strength has been replaced with an alternative method; and The test method for the determination of the thermal resistance has been enlarged in its scope.

Specification for laminated pressboard - Part 2: Methods of test

IEC 61340-3-2:2006 静电学.第3-2部分:静电感应模拟方法.机械模型(MM).静电放电试验波

This part of IEC 61340 describes the discharge current waveforms used to simulate machine model (MM) electrostatic discharges (ESD) and the basic requirements for equipment used to develop and verify these waveforms. This standard covers MM ESD waveforms for use in general test methods and for application to materials or objects, electronic components and other items for ESD withstand test or performance evaluation purposes. The specific application of these MM ESD waveforms to non-powered semiconductor devices is covered in IEC 60749-27.

Electrostatics - Part 3-2: Methods for simulation of electrostatic effects - Machine model (MM) electrostatic discharge test waveforms

CNS 14959-2005 时变电场、磁场及电磁场曝露之限制值(300ＧＨｚ以下)

本标准规定曝露于时变电场、磁场及电磁场之限制值，包含基本限制及参考位准。本标准主要目的在于制定各类标准，限制电磁场曝露，防止各种不利于健康之影响。不良健康影响会造成曝露个

Limits for exposuring to time-varying electric, magnetic and electromagnetic fields (up to 300 GHz)

EN 60371-2:2004 云母基绝缘材料规范 第2部分：试验方法

Defines the methods of test which are applicable to built-up mica materials, products based on them and mica paper. The main changes from the previous edition are as follows: a) All clauses re-numbered. b) Relevant template of ISO 67 has been added to this standard as Annex A. c) Clause 8: Tensile strength and elongation at break Procedure modified to give rate of movement instead of time limit. Different rate of movement for raw mica as opposed to reinforced and/or impregnated mica. d) Clause 11: Stiffness Size of test specimen revised. Wording modified so that standard covers materials using carriers other than woven glass cloth and materials that are 3-ply. Revision of terms machine direction and transverse direction. (These were incorrect in second edition (1987).) e) Clause 13: Elastic compression and plastic compression Tolerance on measurement of height of stack changed to within 0,01 mm. Times for change in pressure in procedure changed to 1 min. f) Clause 16: Electric strength Modified in line with Amendment 1 (1994) to the second edition (1987). Changes relate to latest edition of EN 60243-1. g) Clause 19: Detection of defects and conductive particles Revised subclause.

Specification for insulating materials based on mica - Part 2: Methods of test

KS C IEC 60554-2-2003(2018) 电工用纤维素纸第2部分:试验方法

Cellulose paper for electrical applications - Part 2: Test methods

KS C IEC 60554-2:2003 电工用纤维素纸.第2部分:试验方法

이 규격은 IEC 60554-3의 시방에서 규정하고 있는 요구 조건을 맞추기 위하여 전

Cellulosic papers for electrical purposes－Part 2：Methods of test