21.040.30 特殊螺纹 标准查询与下载

NF E03-601:1974 额定推力的锥螺纹

TAPER PIPE THREADS,NPT.

JIS B 0201:1973 微型螺纹

この規格は，時計，光学機器，電気機器，計測器などに用いる呼び径0.3-1.4 m mミニチュアねじの基準山形，公式，基準寸法，等級，許容限界寸法及び公差について規定し，公差方式は附属書に示す。ただし，呼び径1-1.4 mmのミニチュアねじは，時計工業などにおいて特に必要な場合に限り用いるものとし，他の一般の場合は，JIS B 0205（メートル並目ねじ）による。参考 このミニチュアねじは，ISO R 1501 (ISO miniature screw threads)に規定されているISOミニチュアねじと一致している。

Miniature screw threads

DIN 264-1:1973 螺距为 7mm 的带间隙和直侧面的圆螺纹.第1部分:公称尺寸

Round thread with clearance and flat flank with pitch 7 mm; nominal sizesGewinde nach dieser Norm wird haupts?chlich bei Kupplungsspindeln angewendet.

Round Screw Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Dimensions

DIN 262-1:1973 螺距为7mm 的带间隙和直侧面的圆螺纹.标称尺寸

Round thread with clearance and steep flank with pitch 7 mm; theoretical valuesGewinde nach dieser Norm wird haupts?chlich bei Bremszugstangen, Spannschl?ssern und Zughaken angewendet.

Round Screw Thread with Clearance and Steep Flank with Pitch 7 mm; Nominal Dimensions

DIN 30295-2:1973 倒圆角的梯形螺纹.第2部分:螺纹极限尺寸与公差.螺纹量规的允许误差与允许磨损

Rounded trapezoidal thread; limits of sizes and deviations; tolerances and permissible wear of thread gauges

Rounded Trapezoidal Threads; Limiting Screw Thread Dimensions and Allowances; Permissible Deviations and Permissible Wear of Thread Gauges

DIN 264-2:1973 螺距为 7mm 的带间隙和直侧面的圆螺纹.第2部分:螺纹极限尺寸和螺纹量规的允许偏差和允许磨损

Round thread with clearance and flat flank with pitch 7 mm; limits of sizes and deviation — tolerances and permissible wear of thread gauges

Round Screw Thread with Clearance and Flat Flank with Pitch 7 mm; Limiting Dimensions of Screw Threads and Allowances Permissible Deviations and Permissible Wear of Screw Thread Gauges

DIN 262-2:1973 螺距为7mm 的带公差和斜侧面的圆螺纹.螺纹的极限尺寸及螺纹量规的允许偏差和允许磨损量

Round thread with clearance and steep flank with pitch 7 mm; limits of sizes and deviations — tolerances and permissible wear of thread gauges

Round Screw Thread with Clearance and Steep Flank with Pitch 7 mm; Limiting Dimensions of Screw Threads and Allowances-Permissible Deviations and Permissible Wear of Screw Thread Gauges

DIN 30295-1:1973 倒圆角的梯形螺纹.第1部分:公称尺寸

Rounded trapezoidal thread; nominal sizesGewinde nach dieser Norm wird in der Hauptsache bei Federspannschrauben an Lokomotiven verwendet.

Rounded Trapezoidal Threads; Nominal Dimensions

ASME B1.5-1973 梯形螺纹

Acme Screw Threads

DIN 103-8:1972 ISO 米制梯形螺纹.标称直径105至300mm螺栓螺纹的极限尺寸

ISO Metric Trapezoidal external screw threads from 105 to 300 mm diameter; limits

ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal Diameter

DIN 103-5:1972 ISO 米制梯形螺纹.标称直径8～100mm螺母螺纹的极限尺寸

ISO Metric Trapezoidal internal screw threads from 8 to 100 mm diameter; limits

ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter

DIN 103-7:1972 ISO 米制梯形螺纹.标称直径8～100mm螺栓螺纹的极限尺寸

ISO Metric Trapezoidal external screw threads from 8 to 100 mm diameter; limits

ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal Diameter

DIN 7273-1:1970 厚度0.5mm以下钢板零件及配合件用圆螺纹.尺寸、公差

Knuckle threads for steel sheet pieces up to 0,5 mm thickness and appropriated couplings; sizes and tolerances

Knuckle Threads for Steel Sheet Pieces up to 0.5 mm Thickness and Appropriated Couplings; Dimensions, Tolerances

GOST 13536-1968 卫生设备装置用圆螺纹.剖面,基本参数和公差

Настоящий стандарт распространяется на круглую резьбу для шпинделей вентилей смесителей и туалетных кранов, водопроводных кранов

Round thread for sanitary fittings. Profile, basic dimensions, tolerances

KS B 0225-1965(2010) 缝纫线

Sewing Machine Screw

KS B 0224-1964(2012) 自行车螺丝

Bicycle Threads

CSN 25 4190-1964 螺纹孔径规标准规 G '/a" 到 G 3 x/2"圆柱形导管螺纹

Master gauges for thread calliper gauges. Cylindrical pipe thread G 1/8" - G 3 1/2"

BS 919-4:1964 螺纹量规极限和公差规范.第4部分:直径 1/4英寸以上(含 1/4英寸)的统一型螺纹量规的尺寸极限

Gauges, setting plugs and check plugs for standard Unified Coarse (UNC), Fine (UNF) and Unified Extra Fine (UNEF) threads (BS 1580:Parts 1 and 2). $7IGo$7R and $7Inot go$7R screw plug, solid screw ring, adjustable screw ring, and adjustable screw caliper gauges; double length setting plugs for $7Igo$7R and $7Inot go$7R adjustable screw ring gauges and single length setting plugs for adjustable screw caliper gauges; $7Igo$7R and $7Inot go$7R plain plug and caliper gauges for the crest diameters of product threads.

Specification for screw gauge limits and tolerances - Limits of size for gauges for screw threads of Unified form diameters 1/4 in and larger

CSN 25 4346-1961 穿过型边新螺纹环校准量规 V型螺纹（80°牙侧角）

Screw gauges. Reference gauges for new thread rings with "go" side. V-thread (angle between the flanks=80 grads)

CSN 25 4348-1961 穿过型边螺纹环耐磨校准量规．V型螺纹环（80°牙侧角）

Screw gauges. Reference gauges on wear for thread rings with "go" side. V-thread (angle between flanks=80 grads)