23.020.40 低温容器 标准查询与下载

BS ISO 21013-3:2006 低温容器.低温设施用泄压附件.尺寸和容量测定

Cryogenic vessels - Pressure-relief accessories for cryogenic service - Sizing and capacity determination

DS/EN 13648-1:2009 低温容器 防止过压的安全装置 第1部分：低温服务安全阀

This European Standard specifies the requirements for the design, manufacture and testing of safety valves for cryogenic service, that is to say for operation with cryogenic fluids (as defined in EN 1251-1) below - 10 °C in addition to operation at ambient temperature. It is a requirement of this European Standard that the valves comply with EN ISO 4126 1 or EN ISO 4126-4. In the event of different requirements, the requirements for cryogenic service shall be applied.NOTE 1 A cryogenic fluid (refrigerated liquefied gas) is a gas which is partially liquid because of its low temperature (including totally evaporated liquids and supercritical fluids).This Euro

Cryogenic vessels - Safety devices for protection against excessive pressure - Part 1: Safety valves for cryogenic service

BS ISO 21011:2009 低温容器 低温设施用阀门

Cryogenic vessels. Valves for cryogenic service

BS ISO 21011:2008 低温容器.低温设施用阀门

Cryogenic vessels - Valves for cryogenic service

DS/EN 1626:2008 低温容器 低温服务阀门

This European Standard specifies the requirements for the design, manufacture and testing of valves for cryogenic service, i.e. for operation with cryogenic fluids (as defined in EN 1251-1) below - 10 °C as well as at ambient conditions to allow for start-up and run-down. It specifies additional requirements for cryogenic service for the appropriate valve product standard.NOTE a cryogenic fluid (refrigerated liquefied gas) is a gas which is partially liquid because of its low temperature (including totally evaporated liquids and supercritical fluids). It applies to sizes up to DN 150 including vacuum jacketed cryogenic valves.This European Standard is not a

Cryogenic vessels - Valves for cryogenic service

DIN EN 14398-2:2008 低温容器.大型可运输非真空绝缘容器.第2部分:设计、制造、检查和试验

This European Standard specifies requirements for the design, fabrication, inspection and testing of large transportable non vacuum insulated cryogenic vessels of more than 1000 I volume, which are permanently (fixed tanks) or not permanently (demountable tanks) attached to a vehicle, for carriage by road However, it can be used for other mode of transport providing the specific regulations/requirements are complied with This European Standard applies to large transportable non vacuum insulated cryogenic vessels for fluids specified in EN 14398-1 and does not apply to vessels designed for toxic fluids. This European Standard does not include the general vehicle requirements e.g. running gear, brakes, lighting etc that shall be in accordance with the relevant standards/regulations.

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing; German version EN 14398-2:2003+A2:2008

BS ISO 21009-1:2008 低温容器.静压真空绝缘容器.设计、制造、检验和试验

Cryogenic vessels - Static vacuum-insulated vessels - Design, fabrication, inspection and tests

ISO 21009-1:2008 低温容器.静压真空绝缘容器.第1部分:设计、制造、检验和试验

Cryogenic vessels - Static vacuum-insulated vessels - Part 1: Design, fabrication, inspection and tests

BS ISO 21013-1:2008 低温容器.低温设备用卸压附件.可重新盖紧的卸压阀

Cryogenic vessels - Pressure-relief accessories for cryogenic service - Reclosable pressure-relief valves

ISO 21013-1:2008 低温容器.低温设备用卸压附件.第1部分:能重新盖紧的卸压阀

This International Standard specifies the requirements for the design, manufacture and testing of pressure relief valves for cryogenic service, i.e. for operation with cryogenic fluids in addition to operation at temperatures from ambient to cryogenic. It is a requirement of this International Standard that the valves comply with ISO 4126-1; in the event of different requirements, this International Standard takes precedence. This International Standard is restricted to valves not exceeding a size of DN 150 designed to relieve single-phase vapours or gases. A valve may be specified, constructed and tested such that it is suitable for use with more than one gas or with mixtures of gases. NOTE This part of ISO 21013 does not provide methods for determining the capacity of relief valve(s) for a particular cryogenic vessel. Such methods are provided in ISO 21013-3.

Cryogenic vessels - Pressure-relief accessories for cryogenic service - Part 1: Reclosable pressure-relief valves

LST EN 14398-2-2004+A2-2008 低温容器 大型可运输非真空绝热容器 第2部分：设计、制造、检验和测试

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

DS/EN 14398-2+A2:2008 低温容器 大型可运输非真空绝热容器 第2部分：设计、制造、检验和测试

This European Standard specifies requirements for the design, fabrication, inspection and testing of large transportable non vacuum insulated cryogenic vessels of more than 1000 l volume, which are permanently (fixed tanks) or not permanently (demountable tanks) attached to a vehicle, for carriage by road. However, it can be used for other mode of transport providing the specific regulations/requirements are complied with.This European Standard applies to large transportable non vacuum insulated cryogenic vessels for fluids specified in EN 14398-1 and does not apply to vessels designed for toxic fluids.This European Standard does not include the general veh

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

EN 14398-2:2003+A2:2008 低温容器.大型移动式非真空绝缘容器.第二部分:设计,研制,检查,测试

This European Standard specifies requirements for the design, fabrication, inspection and testing of large transportable non vacuum insulated cryogenic vessels of more than 1000 l volume, which are permanently (fixed tanks) or not permanently (demountable tanks) attached to a vehicle, for carriage by road. However, it can be used for other mode of transport providing the specific regulations/requirements are complied with. This European Standard applies to large transportable non vacuum insulated cryogenic vessels for fluids specified in EN 14398-1 and does not apply to vessels designed for toxic fluids. This European Standard does not include the general vehicle requirements e. g. running gear, brakes, lighting etc. that shall be in accordance with the relevant standards/regulations.

Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing

ISO 21011:2008 低温容器.低温设备的阀门

This International Standard specifies the requirements for the design, manufacture and testing of valves for a rated temperature of −40 °C and below (cryogenic service), i.e. for operation with cryogenic fluids in addition to operation at temperatures from ambient to cryogenic. It applies to all types of cryogenic valves, including vacuum jacketed cryogenic valves up to size DN 150. This International Standard is not applicable to pressure relief valves covered by ISO 21013-1.

Cryogenic vessels - Valves for cryogenic service

BS ISO 21013-2:2007 低温容器.低温设施用卸压附件.打开后不能重新盖紧的卸压装置

ISO 21013-2:2007 specifies the requirements for the design, manufacture and testing of non‑reclosable pressure‑relief devices for cryogenic service, i.e. for operation with cryogenic fluids in addition to operation at temperatures from ambient to cryogenic. ISO 21013-2:2007 is restricted to bursting‑disc and buckling‑pin devices not exceeding a size of DN 200 designed to relieve single‑phase vapours or gases. A bursting‑disc or buckling‑pin assembly may be specified, constructed and tested such that it is suitable for use with more than one gas or with mixtures of gases. ISO 21013-2:2007 does not provide methods for determining the capacity of bursting disc or buckling pin devices for a particular cryogenic vessel. Such methods are provided in ISO 21013-3.

Cryogenic vessels - Pressure-relief accessories for cryogenic service - Non-reclosable pressure-relief devices

ISO 20421-1:2006/cor 1:2007 低温容器.大型可运输真空隔热容器.第1部分:设计、制造、检验和测试.技术勘误1

This standard is Cryogenic vessels - Large transportable vacuum-insulated vessels - Part 1: Design, fabrication, inspection and testing Technical Corrigendum 1

Cryogenic vessels - Large transportable vacuum-insulated vessels - Part 1: Design, fabrication, inspection and testing; Technical Corrigendum 1

DIN EN 14197-2 Berichtigung 1:2007 低温容器.静态非真空绝缘容器.第2部分:设计、制造、检验和测试.DIN EN 14197-2-2006技术勘误

Cryogenic vessels - Static non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing; German version EN 14197-2:2003 + A1:2006, Corrigenda to DIN EN 14197-2:2006-11; German version EN 14197-2:2003/AC:2006

DIN EN 13530-2 Berichtigung 1:2007 低温容器.大型可运输真空绝缘容器.第2部分:设计、制造、检验和测试.DIN EN 13530-2-2003技术勘误

Cryogenic vessels - Large transportable vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing; German version EN 13530-2:2002, Corrigenda to DIN EN 13530-2:2003-01; German version EN 13530-2:2002/AC:2006

DIN EN 13458-2 Berichtigung 1:2007 低温容器.静压真空绝缘容器.第2部分:设计、制造、检验和测试.DIN EN 13458-2-2003技术勘误

Cryogenic vessels - Static vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing; German version EN 13458-2:2002, Corrigenda to DIN EN 13458-2:2003-02; German version EN 13458-2:2002/AC:2006

DIN EN 1251-2 Corrigendum 1:2007 低温容器.体积不大于1000升的可运输真空隔热容器.第2部分:设计、制造、检验和测试.DIN EN 1251-2-2000英文版的技术勘误1

Cryogenic vessels- Transportable vacuum insulated vessels of not more than 1 000 litres volume- Part 2: Design, fabrication,inspection and testing Corrigendum 1 to English version of DIN EN 1251-2:2000-03