23.040.90 标准查询与下载

GB/T 1047-1995 管道元件的公称通径

本标准规定了管道元件公称通径的定义、标记及系列。 本标准适用于输送流体用管道元件的公称通径。

Nominal size for pipe components

GB/T 1048-1990 管道元件公称压力

本标准规定了金属管道元件公称压力的定义、标记及系列。 本标准适用于金属管道元件公称压力分级。 本标准不适用于液压、气动系统及石油钻采设备等行业的公称压力分级。

Nominal pressure for pipe components

GB/T 7231-1987 工业管路的基本识别色和识别符号

本标准对工业管路的基本识别色和识别符号的含义及作用作出规定。 本标准适用于工业生产中气体和液体的输送管路。

Basic identification colours and code indications for industrial pipelines

KS W 0611-2013 航空航天-管道-识别

Aerospace -Pipelines-Identification

KS M 3407-2003 一般用聚乙烯管

이 규격은 일반용으로 사용하는 폴리에틸렌 관(이하 관이라 한다.)에 대하여 규정한다.

Polyethylene pipe for general purpose

CSA Z662-1996 石油和天然气管道系统

1. Scope 1.1 This Standard covers the design, construction, operation, and maintenance of oil and gas industry pipeline systems that convey (a) liquid hydrocarbons, including crude oil, multiphase fluids, condensate, liquid petroleum products, natural gas liquids, and liquefied petroleum gas; (b) oilfield water; (c) oilfield steam; (d) carbon dioxide used in oilfield enhanced recovery schemes; or (e) gas*. *Designers are cautioned that the requirements in this Standard may not be appropriate for gases other than natural gas, manufactured gas, or synthetic natural gas. 1.2 The scope of this Standard, as shown in Figures 1.1 and 1.2, includes (a) for oil industry fluids, piping in offshore pipelines, onshore pipelines, tank farms, pump stations, pressure-reducing stations, and measuring stations; (b) oil pipeline pump stations, pipeline tank farms, and pipeline terminals; (c) for carbon dioxide pipeline systems, piping in onshore pipelines, pressure-reducing stations, and measuring stations; (d) for gas industry fluids, piping in offshore pipelines, onshore pipelines, compressor stations, measuring stations, and pressure-regulating stations; (e) gas compressor stations; and (f) gas storage lines and pipe-type and bottle-type gas storage vessels. 1.3 This Standard does not apply to (a) design and fabrication of pressure vessels that are covered by appropriate pressure vessel codes; (b) piping with metal temperatures below -70°C; (c) piping other than oilfield steam distribution piping, with metal temperatures above 230°C; Note: Although not specifically covered by this Standard, designs for higher temperatures may be used, provided that the effects of such higher temperatures are accounted for. (d) gas piping beyond the outlet of the customer's meter set assembly (which is covered by CGA Standard CAN/CGA-B149.1); (e) piping in natural gas liquids extraction plants, gas processing plants (except main gas stream piping in dehydration and all other processing plants installed as part of gas pipeline systems), gas manufacturing plants, industrial plants, and mines; (f) oil refineries, terminals other than pipeline terminals, and marketing bulk plants; (g) in-plant piping for drinking, make-up, or boiler feed water; (h) casing, tubing, or pipe in oil or gas wells, wellheads, separators, production tanks, and other production facilities; (i) vent piping for waste gases of any kind operating at or near atmospheric pressure; (j) heat exchangers; (k) prefabricated units that employ plate and longitudinal welds rather than pipe; (l) liquefied natural gas systems; (m) liquid fuel distribution systems; (n) loading/unloading facilities for tankers or barges; (o) natural gas refuelling stations; and (p) hydrocarbon storage in underground formations and associated equipment (which is covered by CSA Standard Z341). 1.4 This Standard is intended to establish essential requirements and minimum standards for the design, construction, and operation of oil and gas industry pipeline systems. This Standard is not a design handbook and the exercise of competent engineering judgement is a necessary requirement to be employed concurrently with its use. 1.5 The requirements of this Standard are applicable to the operation, maintenance, and upgrading of existing installations; however, it is not intended that such requirements be applied retroactively to existing installations insofar as design, construction, and established operating pressure are concerned. 1.6 Where any requirements of this Standard are at variance with the requirements of other standards or codes incorporated by reference into this Standard, the requirements of this Standard shall govern. 1.7 It is not the intent of this Standard to prevent the development of new equipment or practices, or to prescribe how such innovations should be handled.

Oil and Gas Pipeline Systems

STAS SR ISO 9356:1996 有或没有连接组件的聚烯烃管组件．抗内部压力．测试法

Polyolefin pipe assemblies with or without jointed flttings -Resistance to internai pressure - Test method

STAS SR ISO 3501:1995 聚乙烯（PE）压力管材和管件间的装配街头．抗拉拔实验

Prezentul Standard Interna?ional stabile?te metoda de verificare a rezisten?ei ?a trac?iune longitudinal? a asambl?rilor (cu excep?ia asambl?rilor sudate prin fuziune) ?ntre fitinguri ?i ?evi de polietilen? (PE) sub presiune. Aceast? metod? se aplic? indiferent de materialul ?i felul fitingului utilizat pentru asamblarea ?evilor de polietilen? ?i nu se aplic? dec?t fitingurilor destinate ?evilor al c?ror diametru exterior nominal este mai mic sau egal cu 63 mm (2,480 in).

Assembled joints between fittings and polyethylene (PE) pressure pipes - Test of resistbnce to pull out

ASME B31.3c Addenda-1995 化工厂和石油精炼管.附录

Chemical plant and petroleum refinery piping; Addenda

ASME B31.5 Interpretations 5-1994 包括说明号为5的制冷管B31.5-1992的说明件

This Code prescribes requirements for the materials, design, fabrication, assembly, erection, test, and inspection of refrigerant, heat transfer components, and secondary coolant piping for temperatures as low as -320?F (-196?C), whether erected on the premises or factory assembled, except as specifically excluded in the standard.

Interpretations 5: Refrigeration piping

ASME B31.1c Addenda-1994 动力管道.修改件

This code prescribes minimum requirements for the design, materials, fabrication, erection, test, and inspection of power and auxiliary service piping systems for electric generation station, industrial and institutional plants, central and district heating plants, and district heating systems.

Power piping; Addenda

ASME B31.1 Interpretations 25-1994 说明:动力管道

This code prescribes minimum requirements for the design, materials, fabrication, erection, test, and inspection of power and auxiliary service piping systems for electric generation station, industrial and institutional plants, central and district heating plants, and district heating systems.

Interpretations 25: Power piping

ASME B31.5a Addenda-1994 制冷管道.修改件

Refrigeration piping; Addenda

ASME B31.3b Addenda-1994 化工厂和炼油厂管道.修改件

Chemical plant and petroleum refinery piping; Addenda

ASME B31.3 Cases NO. 2-1993 压力管道用套管规程.套管141:在ANSI/ASME B 31.3管道标准中铝合金法兰的使用规则

This Code prescribes requirements for materials and components, design, fabrication, assembly, erection, examination, inspection, and testing of piping typically found in petroleum refineries; chemical, pharmaceutical, textile, paper, semiconductor, and cryogenic plants; and related processing plants and terminals.

Cases code for pressure piping - Case 141: Rules for use of aluminium alloy flanges in ANSI/ASME B 31.3 piping

ASME B31.3-1993 化学厂和石油炼制管道

Chemical plant and petroleum refinery piping

ASME B31.3a Addenda-1993 化工厂和炼油厂管道.修改件

Chemical plant and petroleum refinery piping; Addenda

DIN 30675-1:1992 地下敷设的管道的外层防腐.钢管的防腐措施

The document is valid for the external corrosion protection of burted steel pipes.

External corrosion protection of buried pipes; corrosion protection systems for steel pipes

ASME B31.4-1992 烃类,液化石油气,无水氨和醇类用液体输送系统

Liquid transportation systems for hydrocarbons, liquid petroleum gas, anhydrous ammonia, and alcohols

DIN 30677-1:1991 埋设管道的腐蚀保护.第1部分:公称要求的涂层

Corrosion protection of burried valves; coating for normal requirement