共找到 545 条与 过滤器、密封垫和流体杂质 相关的标准,共 37 页
The theoretical correlation method between the cleanliness of the hydraulic transmission system and the cleanliness and oil pollution of the components that make up the system
本文件描述的方法适用于: a)液压系统总成油液污染度的检验; b)出厂前液压系统目标清洁度的验证; c)如果需要,将液压系统净化至目标清洁度。 本文件规定的清洗步骤不是用来替代合适的系统清洗程序,系统清洗程序参见ISO23309。液压系统中使用的零件和元件在装配前宜经过清洗,指导准则参见ISO18413。
Hydraulic fluid power—System—Clean-up procedures and verification of cleanliness method
本文件规定了在线液体自动颗粒计数系统的校准和验证方法。 本文件适用于以下用途: ———用于液体自动颗粒计数器校准悬浮液制备设备的验证; ———进行液体自动颗粒计数器的在线校准; ———两台及两台以上在线液体自动颗粒计数器的匹配,例如,对两台关联在线液体自动颗粒计数器在给定尺寸下的颗粒进行计数; ———对带稀释或不带稀释的在线颗粒计数系统进行验证,例如,测定GB/T18853 规定的过滤器多次通过试验中液压过滤器的过滤效率。
Hydraulic fluid power—On-line automatic particle-counting systems for liquids—Methods of calibration and validation
本文件规定了一种从正在工作的液压系统中提取液样的方法和程序。 本文件适用于液压系统颗粒污染分析用液样的提取。
Hydraulic fluid power—Particulate contamination analysis—Extraction of fluid samples from lines of an operating system
本文件规定了液压缸活塞和活塞杆用同轴密封件安装沟槽的符号、型式、尺寸系列和公差、安装导入角的轴向长度、间隙。 本文件适用于安装在往复运动液压缸活塞和活塞杆中起密封作用的孔用方形同轴密封件、孔用组合同轴密封件、轴用阶梯形同轴密封件。
Dimensions series of rod and piston dynamic seals for hydraulic cylinders—Part 3:Dimensions and tolerances of groove for co-axial seals
本文件规定了液压缸活塞和活塞杆动密封装置支承环安装沟槽的符号、系列号、型式、尺寸系列和公差、间隙。 本文件适用于往复运动液压缸活塞和活塞杆用支承环安装沟槽。
Dimensions series of rod and piston dynamic seals for hydraulic cylinders—Part 4:Dimensions and tolerances of bearing rings groove
本文件规定了利用滤膜阻塞技术(也称为网眼遮挡法或孔阻塞技术)在线或离线半定量监测液体颗粒污染度的方法。 本文件还规定了实验室及现场校准仪器以及验证仪器正确使用的操作程序。 本文件描述的方法适用于监测: a)液压系统的清洁度; b)冲洗过程; c)辅助设备和试验台。该方法适用于所有单相或多相液体系统。
Hydraulic fluid power—Monitoring the level of particulate contamination of the fluid—Part 3:Use of the filter blockage technique
本文件规定了液压缸活塞用带支承环组合密封沟槽的符号、型式、尺寸和公差。 本文件适用于安装在缸径20mm~500mm 的往复运动液压缸活塞上起双向密封作用的带支承环组合密封(以下简称组合密封)。
Types, dimensions and tolerances of groove for seals with bearing rings for hydraulic cylinders piston
本标准规定了液压滤芯热工况及模拟在移动液压系统应用中可能遇到的冷启动的试验程序,该试验程序除了使试验结果具有良好的复现性,也可作为ISO11170 中规定的其他滤芯性能试验之前的试验程序。
Hydraulic fluid power—Filter element test methods—Thermal conditioning and cold start-up simulation
GB/T20671 的本部分规定了非金属垫片材料蠕变松弛率测定的原理、仪器设备、样品、试验步骤、精密度及试验报告。 本部分适用于 GB/T20671.1 规定的 1 型、5 型和 7 型材料的蠕变松弛率的测定。 其他型号的材料亦可参照采用。
Classification system and test methods for nonmetallic gasket materials—Part 5: Standard test method for creep relaxation of gasket materials
GB/T20671 的本部分规定了非金属垫片材料的分类方法.代码定义.厚度要求和测量方法、取样、试样调节。本部分适用于以石棉.软木.纤维素及其他无机或有机材料结合各种务结剂或浸渍剂而制成的材料,不适用于橡胶制品材料.垫片涂层材料或多层复合垫片材料,但多层复合垫片材料的面层单层材料也适用于本分类体系。
Classification system and test methods for nonmetallic gasket materials—Part 1:Standard classification system for nonmetallic gasket materials
GB/T20671 的本部分规定了非金属垫片材料与金属表面黏附性试验的原理、仪器设备、样品、试验步骤、精密度及试验报告。 本部分适用于聚四氟乙烯垫片、纤维垫片、石墨垫片等非金属垫片与金属表面黏附性的测定。
Classification system and test methods for nonmetallic gasket materials—Part 6: Standard test method for adhesion of gasket materials to metal surfaces
GB/I20671 的本部分规定了非金属垫片材料在试验液体中浸渍后其物理性能所受影响程度的测定方法的原理、仪器设备.试验样品.试验程序.试验报告及精密度。本部分适用于GB/T20671.1一2020 描述的1型.2型.3型和7型材料的耐液体性能的测定。
Classification system and test methods for nonmetallic gasket materials—Part 3: Standard test method for fluid resistance of gasket materials
Hydraulic fluid power—Filter elements—Sequence of tests for verifying performance characteristics
Hydraulic fluid power—Filter elements—Part 4: Method for rated end load test
Hydraulic fluid power—Filter elements—Determination of resistance to flow fatigue using high viscosity fluid
Hydraulic fluid power—Determination of the particulate contamination level of a liquid sample by automatic particle counting using the light-extinction principle
GB/T37162 的本部分规定了用于监测液压系统颗粒污染上度的方法和技术,同时描述了各种方法的优缺点,以便在给定条件下正确选择监测方法。 本部分描述的方法适用于监测; a)液压系统的清洁度; b)冲洗过程; c)辅助设备和试验台。 本部分也适用于其他液体(例如:润滑油.燃油.处理液)的监测。 注:用于监测蜂粒污染的仪器不能当作或称为颗粒计数器,即使它们采用了与颗粒计数器相同的物理原理。
Hydraulic fluid power—Monitoring the level of particulate contamination of the fluid—Part 1: General principles
本标准规定了微孔膜滤芯用卫生级过滤器外壳(以下简称“外壳”)的材料、设计、制造、检验,以及标志、清洗、包装、随机文件的技术要求。 本标准适用于不锈钢制微孔膜滤芯用卫生级过滤器外壳。
Specification of hygienic housing for microfiltration membrane elements
Dimensions series of rod and piston dynamic seals for hydraulic cylinders—Part 1:Dimensions and tolerances of co-axial seals for reciprocating applications
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号