共找到 1856 条与 模制设备和铸造设备 相关的标准,共 124 页
本部分规定了塑料注射模用带肩导柱的尺寸规格和公差。 本部分适用于塑料注射模所用的带肩导柱。 本部分还给出了材料指南和硬度要求,并规定了带肩导柱的标记。
Components of injection moulds for plastics.Part 5:Shouldered guide pillar
本部分规定了塑料注射模用复位杆的尺寸规格和公差。 本部分适用于塑料注射模所用的复位杆。 本部分还给出了材料指南和硬度要求,并规定了复位杆的标记。
Components of injection moulds for plastics.Part 13:Return pin
本部分规定了塑料注射模用直导套的尺寸规格和公差。 本部分适用于塑料注射模所用的直导套。 本部分还给出了材料指南和硬度要求,并规定了直导套的标记。
Components of injection moulds for plastics.Part 2:Straight guide bush
本部分规定了塑料注射模用带肩推杆的尺寸规格和公差。 本部分适用于塑料注射模所用的带肩推杆。 本部分还给出了材料指南和硬度要求,并规定了带肩推杆的标记。
Components of injection moulds for plastics.Part 16:Shouldered ejector pin
本部分规定了塑料注射模用拉杆导柱的尺寸规格和公差。 本部分适用于塑料注射模所用的拉杆导柱。 本部分还给出了材料指南和硬度要求,并规定了拉杆导柱的标记。
Components of injection moulds for plastics.Part 20:Limit pin
本部分规定了塑料注射模用矩形定位元件的尺寸规格和公差。 本部分适用于塑料注射模所用的矩形定位元件。 本部分还给出了材料指南和硬度要求,并规定了矩形定位元件的标记。
Components of injection moulds for plastics.Part 21:Rectangular locating element
本部分规定了塑料注射模用带头导套的尺寸规格和公差。 本部分适用于塑料注射模所用的带头导套。 本部分还给出了材料指南和硬度要求,并规定了带头导套的标记。
Components of injection moulds for plastics.Part 3:Headed guide bush
本部分规定了塑料注射模用推管的尺寸规格和公差。 本部分适用于塑料注射模所用的推管。 本部分还给出了材料指南和硬度要求,并规定了推管的标记。
Components of injection moulds for plastics.Part 17:Ejector sleeve
本部分规定了塑料注射模用带头导柱的尺寸规格和公差。 本部分适用于塑料注射模所用的带头导柱,可兼作推板导柱。 本部分还给出了材料指南和硬度要求,并规定了带头导柱的标记。
Components of injection moulds for plastics.Part 4:Headed guide pillar
本部分规定了塑料注射模用限位钉的尺寸规格和公差。 本部分适用于塑料注射模所用的限位钉。 本部分还给出了材料指南和硬度要求,并规定了限位钉的标记。
Components of injection moulds for plastics.Part 9:Stop pin
本部分规定了塑料注射模用定位圈的尺寸规格和公差。 本部分适用于塑料注射模所用的定位圈。 本部分还给出了材料指南和硬度要求,并规定了定位圈的标记。
Components of injection moulds for plastics.Part 18:Locating ring
本部分规定了塑料注射模用圆形拉模扣的尺寸规格和公差。 本部分适用于塑料注射模所用的圆形拉模扣。 本部分还给出了材料指南和硬度要求,并规定了圆形拉模扣的标记。
Components of injection moulds for plastics.Part 22:Round mould opening delayer
本标准规定了塑料注射模的要求、验收、标志、包装、运输和贮存。 本标准适用于塑料注射模的设计、制造和验收。
Specification of injection moulds for plastics
本标准规定了塑料注射模模架的组合型式、尺寸与标记。 本标准适用于塑料注射模模架。
Injection mould bases for plastics
本标准规定了塑料注射模零件的要求、检验、标志、包装、运输和贮存。 本标准适用于GB/T 4169.1~4169.23-2006规定的塑料注射模零件。
Specification of components of injection moulds for plastics
本部分规定了塑料注射模用矩形拉模扣的尺寸规格和公差。 本部分适用于塑料注射模所用的矩形拉模扣。 本部分还给出了材料指南和硬度要求,并规定了矩形拉模扣的标记。
Components of injection moulds for plastics.Part 23:Rectangular mould opening delayer
本部分规定了塑料注射模用垫块的尺寸规格和公差。 本部分适用于塑料注射模所用的垫块。 本部分还给出了材料指南,并规定了垫块的标记。
Components of injection moulds for plastics.Part 6:Spacer block
本部分规定了塑料注射模用推板的尺寸规格和公差。 本部分适用于塑料注射模所用的推板和推杆固定板。 本部分还给出了材料指南和硬度要求,并规定了推板的标记。
Components of injection moulds for plastics.Part 7:Ejector plate
本部分规定了塑料注射模用推板导套的尺寸规格和公差。 本部分适用于塑料注射模所用的推板导套。 本部分还给出了材料指南和硬度要求,并规定了推板导套的标记。
Components of injection moulds for plastics.Part 12:Ejector guide bush
本部分规定了塑料注射模用模板的尺寸规格和公差。 本部分适用于塑料注射模所用的定模板、动模板、推料板、支承板和定模板座板与动模座板。 本部分还给出了材料指南和硬度要求,并规定了模板的标记。
Components of injection moulds for plastics.Part 8:Mould plate
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号