25.160.01 标准查询与下载

ISO 17779:2021 钎焊.金属材料钎焊程序的规范和鉴定

This document specifies requirements for the specification and qualification of brazing procedures for brazing of metallic materials. This document specifies requirements for brazing of the test piece, testing of the test specimen, essential variables and their range of qualification, acceptance criteria, brazing procedure qualification record (BPQR) and brazing procedure specification (BPS). This document gives general provisions on quality requirements for brazing (see Annex A). This document does not cover testing of residual stresses, corrosion resistance and impact properties. This document applies to the following brazing processes according to ISO 857-2 and ISO 4063:2009 with local and global heating: — 911 Infrared brazing; — 912 Flame brazing, torch brazing; — 913 Laser beam brazing; — 914 Electron beam brazing; — 916 Induction brazing; — 918 Resistance brazing; — 919 Diffusion brazing; — 921 Furnace brazing; — 922 Vacuum brazing; — 923 Dip-bath brazing; — 924 Salt-bath brazing; — 925 Flux bath brazing; — 926 Immersion brazing; — 972 Arc weld brazing. The principles of this document can be applied to other brazing processes and brazing of materials not listed. This document does not apply to brazing for aerospace applications covered by ISO 11745.

Brazing — Specification and qualification of brazing procedures for metallic materials

ISO 13585:2021 钎焊.钎焊工和钎焊操作员的资格鉴定试验

This document specifies requirements for qualification testing of brazers and brazing operators for metallic materials. This document gives general provisions on quality requirements for brazing (see Annex A). This document applies to the following brazing processes according to ISO 857-2 and ISO 4063:2009 with local and global heating: — 911 Infrared brazing; — 912 Flame brazing, torch brazing; — 913 Laser beam brazing; — 914 Electron beam brazing; — 916 Induction brazing; — 918 Resistance brazing; — 919 Diffusion brazing; — 921 Furnace brazing; — 922 Vacuum brazing; — 923 Dip-bath brazing; — 924 Salt-bath brazing; — 925 Flux bath brazing; — 926 Immersion brazing; — 972 Arc weld brazing. This document is not applicable to personnel operating brazing equipment who do not have any direct influence on the quality of the brazed joint, for example, personnel performing exclusively loading/ unloading the brazing unit or just initiating the brazing cycle in automatic brazing. The principles of this document can be applied to other brazing processes and brazing of materials not listed. This document does not apply to brazing for aerospace applications covered by ISO 11745.

Brazing — Qualification testing of brazers and brazing operators

DB1310/T 262-2021 气体保护焊技术条件

本文件适用于廊坊区域使用二氧化碳气体保护焊的焊接工作，其他区域可参照执行

Gas shielded welding technical conditions

SY/T 0452-2021 石油天然气金属管道焊接工艺评定

Welding process assessment of oil and gas metal pipelines

T/CWAN 0051-2021 焊接销售工程师评定标准

本文件规定了焊接销售工程师的职业概况、基本要求、工作要求及比重表。 本文件适用于焊接设备、切割设备、焊接辅机具、焊接材料等产品销售岗位从业人员的分级 评价。

Standard for Qualification of Welding Sales Enginner

T/CWAN 0056-2021 电弧焊焊接烟尘组分

本文件给出了焊接材料、母材、涂层和污染物等在电弧焊过程中排放的焊接烟尘组分。 本文件适用于电弧焊用非合金钢、低合金钢、高合金钢、铝基、镍基、铜基、铸铁、耐磨堆焊和加 工硬化等焊接材料。

Arc welding fume components

T/CWAN 0033-2021 铝合金搅拌摩擦焊体积型缺陷相控阵超声检测规范

本文件规定了采用相控阵超声检测技术（Phased-array ultrasonic testing，PAUT）检测铝合金搅拌摩 擦焊接头体积型缺陷的检测要求及检测结果分级。 本文件适用于厚度为1.5 mm~10 mm的铝合金搅拌摩擦焊接头的检测与评定。其它接头形式、其它 厚度的接头检测与评定可参照执行

Specification for phased array ultrasonic testing of volumetric defects in friction stir welding of aluminum alloys

KS M 1102-2021 溶解乙炔

Dissolved acetylene

DS/EN ISO 3834-5:2021 金属材料熔焊质量要求第5部分：声明符合 ISO 3834-2、ISO 3834-3 或 ISO 3834-4（ISO 3834-5:2021）质量要求所必需的文件）

Quality requirements for fusion welding of metallic materials – Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 (ISO 3834-5:2021)

BS EN ISO 3834-5:2021 金属材料熔焊的质量要求 有必要声明和ISO 3834-2、ISO 3834-3或ISO 3834-4质量要求一致的文件

Quality requirements for fusion welding of metallic materials. Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4

UNI 9737-2021 塑料焊工资格：聚乙烯部件和/或聚丙烯焊工，用于输送可燃气体、水和/或其他压力流体，使用接触热元件和电熔程序 补充

Qualification of welders of plastics: welders of polyethylene components and/or polypropylene, for the conveyance of combustible gases, water and/or other fluids under pressure, using procedures for contact thermal elements and electrofusion - Complementa

UNI 11508-2021 聚乙烯焊接工艺规范和评定 WPS 用于电熔法焊接和 WPS 用于接触式热元件法焊接

Specification and qualification of welding procedures for poliethylene - WPS for welding with the electrofusion method and WPS for welding with the thermal element method by contact

OENORM EN ISO 17660:2021 焊接 钢筋的焊接（ISO/DIS 17660:2021）

Welding - Welding of reinforcing steel (ISO/DIS 17660:2021)

EN ISO 3834-5:2021 金属材料熔焊的质量要求.第5部分:声称符合ISO 3834.2,ISO 3834.3或ISO 3834.4质量要求的本身符合必要要求的文件

Quality requirements for fusion welding of metallic materials - Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 (ISO 3834-5:2021)

ISO 3834-5:2021 金属材料的熔化焊质量要求. 第5部分: 有必要声明和ISO 3834-2、ISO 3834-3或ISO 3834-4质量要求一致的文件

This document specifies the International Standards, including clauses and subclauses, with which conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 can be claimed. NOTE For brazing, see ISO 22688.

Quality requirements for fusion welding of metallic materials - Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4

BS EN ISO 3834-1:2021 金属材料熔焊质量要求 选择适当质量要求水平的标准

Quality requirements for fusion welding of metallic materials. Criteria for the selection of the appropriate level of quality requirements

DS/EN ISO 3834-1:2021 金属材料熔焊质量要求第1部分：质量要求适当等级选择标准（ISO 3834-1:2021）

Quality requirements for fusion welding of metallic materials – Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2021)

DS/ISO 3834-1:2021 金属材料熔焊质量要求第1部分：质量要求适当等级选择准则

Quality requirements for fusion welding of metallic materials – Part 1: Criteria for the selection of the appropriate level of quality requirements

BS EN ISO 3834-4:2021 金属材料熔焊质量要求 基本质量要求

Quality requirements for fusion welding of metallic materials. Elementary quality requirements

PN-EN ISO 3834-4-2021-09 E 金属材料熔焊质量要求 第4部分：基本质量要求（ISO 3834-4:2021）

Quality requirements for fusion welding of metallic materials -- Part 4: Elementary quality requirements (ISO 3834-4:2021)