29.040.10 绝缘油 标准查询与下载

BS EN 60296:2012 电工用液体.互感器和开关装置用未使用矿物绝缘油

Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear

ASTM D2225-04(2012) 用于电绝缘的硅氧烷流体的标准测试方法

1.1 These test methods cover the testing of silicone fluids for use in transformers, capacitors, and electronic assemblies as an insulating or cooling medium, or both. These methods are generally suitable for specification acceptance, factory control, referee testing, and research. 1.2 Although some of the test methods listed here apply primarily to petroleum-based fluids, they are, with minor revisions, equally applicable to silicone fluids. 1.3 Silicone fluids are used for electrical insulating purposes because of their stable properties at high and low temperatures and their relative environmental inertness. 1.4 A list of the properties and standards are as follows: Property Measured Section ASTM Test Method Physical: Color 6 D2129 Flash point 7 D92 Fire point 7 D92 Polychlorinated biphenyl content 8 D4059 Pour point 9 D97 Refractive index 10 D1807 Specific gravity 11 D1298, D1481, D4052 Volatility 12 D4559 Viscosity 13 D445, D2161 Chemical: Neutralization number 14 D974 Water content 15 D1533 Electrical: Relative permittivity 16 D9242 Dielectric breakdown voltage 17 D8773 Dissipation factor 18 D9242 Specific resistance 19 D11692 Compatibility 20 D5282 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Silicone Fluids Used for Electrical Insulation

NF C27-224*NF EN 60567:2012 注油电气设备 - 气体抽样以及游离和溶解气体分析 - 指南.

Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved gases - Guidance.

UL 2798-2012 清洁和气味控制用生物消化添加剂的可持续性

Sustainability for Biological Digestion Additives for Cleaning and Odour Control

UL 2797-2012 RV和/或海洋储存罐添加剂的可持续性:基于生物学

Sustainability for RV and/or Marine Holding Tank Additives: Biologically-based

IEC 61181:2012 充矿物油电气设备.电气设备出厂试验的溶解气体分析(DGA)应用

Mineral oil-filled electrical equipment - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment

BS EN 60475:2011 绝缘液体的取样方法

Method of sampling insulating liquids

BS EN 60567:2011 注油电气设备.游离和溶解气体分析用气体取样.指南

Oil-filled electrical equipment. Sampling of gases and analysis of free and dissolved gases. Guidance

ASTM D1934-95(2012) 通过开口烧杯法对电绝缘石油进行氧化老化的标准试验方法

1.1 This test method covers two procedures for subjecting electrical insulating oils to oxidative aging: 1.1.1 Procedure A, without a metal catalyst, and 1.1.2 Procedure B, with a metal catalyst. 1.2 This test method is applicable to oils used as impregnating or pressure media in electrical power transmission cables if less than 10 % of the oil evaporates during the aging procedures. It applies and is generally useful primarily in the evaluation and quality control of unused oils, either inhibited or uninhibited. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oxidative Aging of Electrical Insulating Petroleum Oils by Open-Beaker Method

ASTM D4768-11 通过气相色谱分析绝缘液体中2,6-二叔丁基对甲酚和2,6-二叔丁基苯的标准试验方法

In new electrical insulating oil, this test method provides a quantitative measure of the amounts of 2,6-ditertiary-butyl para-cresol and 2,6-ditertiary-butyl phenol that have been added to the oil. In a used oil, the test measures the amount of these inhibitors remaining in the oil. This test method is suitable for manufacturing control, specification acceptance, and service evaluation. This test method is used to separate, identify, and quantify the inhibitors with minimal interference and matrix effects. This test method has also been used successfully to determine the inhibitor concentrations in other insulating liquids such as esters and high-temperature hydrocarbons.1.1 This test method covers the determination by gas chromatography of 2,6-ditertiary-butyl para-cresol and 2,6-ditertiary-butyl phenol in new and used insulating liquids at concentrations up to 0.5 %. It includes the determination in Type I and II insulating mineral oils as specified in Specification D3487, but has also been used to measure these inhibitors in other insulating liquids, such as esters and high fire-point hydrocarbons. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Analysis of 2,6-Ditertiary-Butyl Para-Cresol and 2,6-Ditertiary-Butyl Phenol in Insulating Liquids by Gas Chromatography

DIN EN 61099:2011 绝缘液体.电气用未使用过的合成有机酯规范(IEC 61099-2010);德文版本EN 61099-2010

Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes (IEC 61099:2010); German version EN 61099:2010

DS/EN 60666:2011 矿物绝缘油中特定添加剂的检测与测定

IEC 60666:2010 provides methods concerning the detection and determination of specified additives in unused and used mineral insulating oils. The detection methods may be applied to assess whether or not a mineral insulating oil contains an additive as specified by the supplier. The determination methods are used for the quantitative determination of additives known to be present or previously detected by the appropriate detection method. The main changes with respect to the previous edition are listed below: - a change in the title from 'Detection and determination of specified anti-oxidant additives in insulating oils'; - new Annexes B and C which provide

Detection and determination of specified additives in mineral insulating oils

DIN EN 60666:2011 矿物绝缘油中规定的添加剂的检验和测定(IEC 60666-2010);德文版本EN 60666-2010

Detection and determination of specified additives in mineral insulating oils (IEC 60666:2010); German version EN 60666:2010

GOST R 54331-2011 电工应用流体.变压器和开关设备未使用的矿物绝缘油.规范

Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear. Specifications

ASTM D1169-11 电绝缘液体电阻率(电阻系数)的标准试验方法

The resistivity of a liquid is a measure of its electrical insulating properties under conditions comparable to those of the test. High resistivity reflects low content of free ions and ion-forming particles, and normally indicates a low concentration of conductive contaminants.1.1 This test method covers the determination of specific resistance (resistivity) applied to new electrical insulating liquids, as well as to liquids in service, or subsequent to service, in cables, transformers, circuit breakers, and other electrical apparatus. 1.2 This test method covers a procedure for making referee tests with dc potential. 1.3 When it is desired to make routine determinations requiring less accuracy, certain modifications to this test method are permitted as described in Sections 19-26. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 17.6 for a specific warning statement.

Standard Test Method for Specific Resistance (Resistivity) of Electrical Insulating Liquids

ASTM D117-10 石油电绝缘油取样试验方法和规范的标准指南

1.1 This guide describes methods of testing and specifications for electrical insulating oils of petroleum origin intended for use in electrical cables, transformers, oil circuit breakers, and other electrical apparatus where the oils are used as insulating, or heat transfer media, or both. 1.2 The purpose of this guide is to outline the applicability of the available test methods. Where more than one is available for measuring a given property, their relative advantages are described, along with an indication of laboratory convenience, precision, (95 % confidence limits), and applicability to specific types of electrical insulating oils.

Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Oils of Petroleum Origin

DS/CLC/TR 50503:2010 含多氯联苯的电气设备和绝缘液体的库存控制、管理、去污和/或处置指南

The scope of this Technical report is to provide guidance for the activities of inventory, control,management, decontamination and/or disposal of equipment and containers with insulating liquidcontaining PCBs, in compliance with the Council Directives (96/59/EC), using Best AvailableTechniques - BAT - (96/61/EC), Commission Decision (2001/68/EC), Stockholm Convention onPersistent Organic Pollutants (POPs) and/or with appropriate national or local legislation.This Technical report is addressed, in particular, toward the Life Cycle Management (LCM) of insulating liquids and it has been developed in accordance with the following objectives:a) reduction of risk

Guidelines for the inventory control, management, decontamination and/or disposal of electrical equipment and insulating liquids containing PCBs

IEC 60666:2010 矿物绝缘油中规定的添加剂的检验和测定

The methods described in this International Standard concern the detection and determination of specified additives in unused and used mineral insulating oils. The detection methods may be applied to assess whether or not a mineral insulating oil contains an additive as specified by the supplier. The determination methods are used for the quantitative determination of additives known to be present or previously detected by the appropriate detection method.

Detection and determination of specified additives in mineral insulating oils

CLC/TR 50503:2010 含多氯联苯的电气设备和绝缘液体的库存控制、管理、去污和/或处置指南

The scope of this Technical report is to provide guidance for the activities of inventory, control, management, decontamination and/or disposal of equipment and containers with insulating liquid containing PCBs, in compliance with the Council Directives (96/59/EC), using Best Available Techniques - BAT - (96/61/EC), Commission Decision (2001/68/EC), Stockholm Convention on Persistent Organic Pollutants (POPs) and/or with appropriate national or local legislation. This Technical report is addressed, in particular, toward the Life Cycle Management (LCM) of insulating liquids and it has been developed in accordance with the following objectives: a) reduction of risks for workers, public health and the environment, arising from human error, malfunction, or failures of the equipment that could cause fires or spillage of hazardous and Persistent Organic Pollutants (POPS)s; b) implementation of the “Best Available Techniques” (BAT),”Best Environmental Practices”(BEP)and methodologies available for safety, whilst taking into account the surroundings and the criteria of self-sufficiency and functional recovery; c) technical feasibility of the activities within the prescribed time schedules, taking into account current legislation and economic feasibility. NOTE 1 For those CENELEC countries in which the European Directives do not apply, this Technical report has an informative purpose only. Different limits from those given in the present Technical report are required in some countries. NOTE 2 For those countries outside of European Community the Stockholm Convention on Persistent Organic Pollutants (POPs) should be applied. NOTE 3 When reading this Technical report, reference should also be made to Annex C of EN 50195 and Annex B of EN 50225, because in some EU countries (i.e. France, Italy, Poland, Spain, etc.) there are other mandatory requirements.

Guidelines for the inventory control, management, decontamination and/or disposal of electrical equipment and insulating liquids containing PCBs

DIN EN 62535:2009 绝缘液体.测定使用和不使用绝缘油中潜在腐蚀性硫磺的试验方法(IEC 62535-2008).德文版本EN 62535-2009

Insulating liquids - Test method for detection of potentially corrosive sulphur in used and unused insulating oil (IEC 62535:2008); German version EN 62535:2009