29.080.30 绝缘系统 标准查询与下载

IEC 60664-3:2003/AMD1:2010 修改件1.低压系统内设备的绝缘配合.第3部分:防止污染的涂层、灌封或模制的使用

Amendment 1 - Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution

LST EN 60071-1-2006/A1-2010 绝缘配合 第1部分：定义、原则和规则（IEC 60071-1:2006/A1:2010）

Insulation co-ordination -- Part 1: Definitions, principles and rules (IEC 60071-1:2006/A1:2010)

DS/EN 60071-1/A1:2010 绝缘协调 第1部分：定义、原则和规则

This part of IEC 60071 applies to three-phase a.c. systems having a highest voltage for equipment above 1 kV. It specifies the procedure for the selection of the rated withstand voltages for the phase-to-earth, phase-to-phase and longitudinal insulation of the equipment and the installations of these systems. It also gives the lists of the standard withstand voltages from which the rated withstand voltages should be selected.This standard recommends that the selected withstand voltages should be associated with the highest voltage for equipment. This association is for insulation co-ordination purposes only.The requirements for human safety are not covered

Insulation co-ordination - Part 1: Definitions, principles and rules

DIN EN 61857-21:2010 电气绝缘结构.热评定规程.第21部分:通用模式的专门要求.线绕器件(IEC 61857-21-2009).德文版本EN 61857-21-2009

This part of IEC 61857 describes a general-purpose model (GPM) and a tall channel alternative model (GPM-TC) which can be used for the evaluation of wire-wound electrical insulation systems (EIS) where specific electrotechnical products are not available or required.

Electrical insulation systems - Procedures for thermal evaluation - Part 21: Specific requirements for general-purpose models - Wire-wound applications (IEC 61857-21:2009); German version EN 61857-21:2009

IEC 112/143/CD:2010 电绝缘系统(EIS).结合液体和固体组件的热评估.第1部分:一般要求

Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 1: General requirements

LST EN 61857-21-2009 电气绝缘系统 热评估程序 第21部分：通用模型的特定要求 绕线应用（IEC 61857-21:2009）

Electrical insulation systems - Procedures for thermal evaluation -- Part 21: Specific requirements for general-purpose models - Wire-wound applications (IEC 61857-21:2009)

JIS C 60664-4:2009 低压系统范围内设备的绝缘协调.第4部分:高频电压应力的考虑

Insulation coordination for equipment within low-voltage systems -- Part 4: Consideration of high-frequency voltage stress

JIS C 60664-3:2009 低压系统范围内设备的绝缘协调.第3部分:利用涂料,灌封或成型防止污染

Insulation coordination for equipment within low-voltage systems -- Part 3: Use of coating, potting or moulding for protection against pollution

JIS C 60664-5:2009 低压系统内设备的绝缘配合.第5部分:确定不小于2 mm的间隙和爬电距离的综合方法

Insulation coordination for equipment within low-voltage systems -- Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm

DS/EN 61857-21:2009 电气绝缘系统 热评估程序 第21部分：通用模型的特殊要求 绕线应用

This part of IEC 61857 describes a general-purpose model (GPM) and a tall channel alternative model (GPM-TC) which can be used for the evaluation of wire-wound electrical insulation systems (EIS) where specific electrotechnical products are not available or required.

Electrical insulation systems - Procedures for thermal evaluation - Part 21: Specific requirements for general-purpose models - Wire-wound applications

DIN EN 61858:2009 电气绝缘系统 对已确立绕线EIS改进的热评估

Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS (IEC 61858:2008); German version EN 61858:2008

IEC 61857-21:2009 电气绝缘系统.导热性评定规程.第21部分:通用模式的特殊要求.线绕器件

This part of IEC 61857 describes a general-purpose model (GPM) and a tall channel alternative model (GPM-TC) which can be used for the evaluation of wire-wound electrical insulation systems (EIS) where specific electrotechnical products are not available or required.

Electrical insulation systems - Procedures for thermal evaluation - Part 21: Specific requirements for general-purpose models - Wire-wound applications

DIN EN 61857-22:2009 电气绝缘系统 热评估用程序 第22部分:密封圈模型的特殊要求 绕线电气绝缘系统(EIS)

Electrical insulation systems - Procedures for thermal evaluation - Part 22: Specific requirements for encapsulated-coil model - Wire-wound electrical insulation system (EIS) (IEC 61857-22:2008); German version EN 61857-22:2008

LST EN 61857-1-2009 电气绝缘系统 热评估程序 第1部分：一般要求 低电压（IEC 61857-1:2008）

Electrical insulation systems - Procedures for thermal evaluation -- Part 1: General requirements - Low-voltage (IEC 61857-1:2008)

BS EN 61858:2008 电气绝缘系统.对于已建立的散绕绕组电气绝缘系统(EIS)的修改的热评估

This International Standard lists the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification. This standard is applicable to EIS used in wire-wound electrotechnical devices. The test procedures are comparative in that the performance of a candidate EIS is compared to that of a reference EIS, which has proven service experience in accordance with IEC 60505 or has been evaluated by one of the procedures given in the IEC 61857 series.

Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS

BS EN 61858:2009 电气绝缘系统 对已有绕线EIS改进的热评定

Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS

DS/EN 61857-1:2009 电气绝缘系统 热评估程序 第1部分：一般要求 低压

This part of IEC 61857 specifies a general test procedure for the thermal evaluation and qualification of electrical insulation systems (EIS) and establishes a procedure that compares the performance of a candidate EIS to that of a reference EIS.This basic standard is applicable to existing or proposed EIS used in electrotechnical products with an input voltage of up to 1 000 V where the thermal factor is the dominating ageing factor.

Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage

LST EN 61857-22-2009 电气绝缘系统 热评估程序 第22部分：封装线圈模型的特定要求 线绕电气绝缘系统（EIS）（IEC 61857-22:2008）

Electrical insulation systems - Procedures for thermal evaluation -- Part 22: Specific requirements for encapsulated-coil model - Wire-wound electrical insulation system (EIS) (IEC 61857-22:2008)

LST EN 61858-2009 电气绝缘系统 对已建立的线绕 EIS 进行修改的热评估（IEC 61858:2008）

Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS (IEC 61858:2008)

EN 61857-1:2009 电气绝缘系统 热评估程序 第1部分：一般要求 低压

IEC 61857-1:2008 specifies a general test procedure for the thermal evaluation and qualification of electrical insulation systems (EIS) and establishes a procedure that compares the performance of a candidate EIS to that of a reference EIS. This standard is applicable to existing or proposed EIS used in electrotechnical products with an input voltage of up to 1 000 V where the thermal factor is the dominating ageing factor. This third edition cancels and replaces the second edition published in 2004, and constitutes editorial revisions to make this standard compatible with Parts 21 and 22.

Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage