29.100.20 电气和机电元件 标准查询与下载

T/CEC 404.1～404.3-2020 ±800kV特高压换流站金具试验方法

T/CEC 404《±800 kV 特高压换流站金具试验方法》分为三个部分： ——第1 部分：电晕和无线电干扰试验 ——第2 部分：温升及热循环试验 ——第3 部分：抗震试验

Test method for fittings of ±800kV UHV converter station

T/ZZB 1755-2020 电力电缆导体用压接型铜、铝接线端子和连接管

本文件规定了35 kV（Um=40.5 kV）及以下电力电缆导体用压接型铜、铝接线端子和连接管的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存以及质量承诺。 本文件适用于35 kV（Um=40.5 kV）及以下，铜导体截面积范围为（10～630）mm2、铝导体截面积范围为（16～630）mm2的电力电缆导体用压接型铜、铝及铜铝过渡接线端子和铜、铝连接管。

Compression type terminal lugs and ferrules with copper or aluminum for power cables conductors

KS D 5571-2019 照明和电子设备用钍钨丝和棒

Thoriated tungsten wires and rods for lighting and electronic equipment

KS I 4016-2019 空气净化器再生颗粒传感器试验方法

Test methods for remanufactured particle sensor of air purifier

KS I 4014-2019 水净化器的再制造的电磁阀

Test methods for remanufactured solenoid valve of water purifier

T/CEEIA 363-2019 光伏并网发电电能路由器技术规范

本标准规定了光伏并网发电电能路由器（以下简称“光伏电能路由器”）的工作条件、技术要求、试验方法、检验规则、标识、说明和包装等。 本标准适用于系统电压35kV及以下应用于光伏发电领域的基于电力电子变压器技术的电能路由器产品。

Technical specification for photovoltaic grid connected electrical energy router

ASTM B603-07(2018) 电加热元件用拉制或轧制铁 - 铬 - 铝合金的标准规范

1.1 This specification covers annealed, drawn, or rolled shapes for electrical heating and resistance purposes of alloys consisting mainly of iron, chromium, and aluminum as detailed in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Drawn or Rolled Iron-Chromium-Aluminum Alloys for Electrical Heating Elements

ASTM B613-17 滑动电触点用复合材料微型电刷规范制备的标准指南

1.1 This guide defines the criteria for composition, properties, and other requirements for brushes containing a matrix of one or more conducting metallic elements or alloys and one or more lubricating lamellar solids. 1.2 The resulting specification is intended for use where the size (for example, 5 by 3 by 2 mm), shape, or other factors preclude the determination of properties on specimens of the bulk material from which individual brushes are made. 1.3 The requirements recommended herein have been found to be desirable for most brush material composites. Care must be taken in preparing a specification for a pre-existing material that imposition of one or more provisions herein does not alter the material or its performance. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparing Specifications for Miniature Brushes of Composite Materials for Sliding Electric Contacts

KS I 4014-2014 净水器再制造电磁阀试验方法

Test methods remanufactured solenoid valve of water purifier

KS I 4016-2014 空气净化器再制造粒子传感器测试方法

Test methods remanufactured particle sensor of air purifier

CSA C22.2 No.233-2009(R2014) 通信系统用电线和电线组

Scope 1.1 This Standard applies to cords and cord sets intended for indoor use to electrically connect communication systems that have a normal operating voltage-to-ground of less than 150 V rms, and that are installed or used in accordance with the Rules of the Canadian Electrical Code, Part I. 1.2 This Standard applies to single-, paired-, and multi-conductor cords, as well as cord sets, where no part of the cord is subjected to a temperature exceeding 60 °C. 1.3 This Standard does not apply to (a) cords and cord sets that contain conductors other than those used specifically for communications circuits, such as electric light, power, Class I, and Class II circuit conductors (as defined in the Canadian Electrical Code, Part I); or (b) cords or cord sets covered by CSA C22.2 No. 21. 1.4 In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Cords and cord sets for communication systems

ASTM B613-76(2006) 滑动电触点用复合材料微型刷规格的准备准则

Standard Guide for Preparing Specifications for Miniature Brushes of Composite Materials for Sliding Electric Contacts

IEC 61360-4-DB:2005 电子元器件标准数据元素类型和相关分类模式.第4部分:IEC标准数据元素类型和元器件分类的基准集

Standard data element types with associated classification scheme for electric components - Part 4: IEC reference collection of standard data element types and component classes

ANSI/IEEE C57.12.28:2005 底座安装设备标准.外壳完整性

Covers conformance tests and requirements for the integrity of above grade pad-mounted enclosures containing apparatus energized in excess of 600 volts that may be exposed to the public including, but not limited to, the following types of equipment enclosures: pad-mounted capacitors or inductors, pad-mounted distribution transformers, pad-mounted junction enclosures, pad-mounted metering equipment, pad-mounted switchgear.

Standard for Pad-Mounted Equipment - Enclosure Integrity

IEC 61360-4:2005 电子元器件标准数据元素类型和相关分类模式.第4部分:IEC标准数据元素类型和元器件分类的基准集

Specifies the definitions of data element types for electric components and materials and the definitions of the component classes. Provides a set of uniquely identified data element types with an unambiguously defined meaning, a defined value format, an

Standard data element types with associated classification scheme for electric components - Part 4: IEC reference collection of standard data element types and component classes

NF C03-502/A1:2005 电子元器件标准数据元素类型和相关分类模式.第2部分:EXPRESS词典模式

Standard data element types with associated classification scheme for electric components - Part 2 : EXPRESS dictionary schema.

KS D 5571-2004 照明和电子设备用镀钍钨丝和杆

이 규격은 조명 및 전자 기기용 토리에이트 텅스텐(산화토륨을 포함하는 텅스텐) 선(이하

Thoriated tungsten wires and rods for lighting and electronic equipment

KS D 5571-2004(2019) 钍钨丝和棒照明和电子设备

Thoriated tungsten wires and rods for lighting and electronic equipment

KS D 5572-2004 照明及电子设备用钨钼合金丝

TUNGSTEN-MOLYBDENUM ALLOY WIRES FOR LIGHTING AND ELECTRONIC EQUIPMENTS

KS D 5543-2004 用于照明和电子设备的钼棒

MOLYBDENUM RODS FOR LIGHTING AND ELECTRONIC EQUIPMENTS