29.160.40 发电机组 标准查询与下载

GB/T 12786-1991 自动化柴油发电机组通用技术条件

本标准规定了自动化柴油发电机组（以下简称机组）的技术要求、试验方法和检验规则等。 本标准适用于按GB4712《自动化柴油发电机组分级要求》和GB126国《工频柴油发电机组额定功率、电压及转速》制造的三相机组。

Automatic diesel generating sets for general specification

GB/T 10760.1-1989 小型风力发电机技术条件

本标准规定了风轮直接驱动的充电型小型风力发电机的产品品种基本参数、技术要求、检验规则、试验方法以及标志和包装的要求。 本标准适用于风轮直接驱动的充电型小型风力发电机（以下简称发电机）。 本标准不适用于感应子式小型风力发电机。

Specification for small wind generators

GSO ASTM D6224:2024 辅助动力装置设备润滑油在线监测的标准规范

1.1 This practice covers the requirements for the effective monitoring of mineral oil and phosphate ester fluid lubricating oils in service auxiliary (non-turbine) equipment used for power generation. Auxiliary equipment covered includes gears, hydraulic systems, diesel engines, pumps, compressors, and electrohydraulic control (EHC) systems. It includes sampling and testing schedules and recommended action steps, as well as information on how oils degrade. NOTE 1—Other types of synthetic lubricants are sometimes used but are not addressed in this practice because they represent only a small fraction of the fluids in use. Users of these fluids should consult the manufacturer to determine recommended monitoring practices. 1.2 This practice does not cover the monitoring of lubricating oil for steam and gas turbines. Rather, it is intended to complement Practice D4378. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment

24/30491829 DC BS EN 60364-7-751 低压电气装置 第7-751部分 特殊装置或地点的要求 低压发电机组

BS EN 60364-7-751. Low-voltage electrical installations - Part 7-751. Requirements for special installations or locations – Low voltage generating sets

24/30491830 DC BS EN 63497 ED1 草案 并联主动校正装置 (ACD)

Draft BS EN 63497 ED1. Parallel Connected Active Correction Devices (ACD)

T/QGCML 3946-2024 柴油发电机组维护保养规范

本文件规定了柴油发电机组维护保养规范的术语和定义、总体要求、人员要求、机组运行要求、维护与保养、故障查询。 本文件适用于柴油发电机组维护保养。

Diesel generator set maintenance specifications

T/CEEIA 759-2023 变电站应急发电机组安全技术规范

本文件规定了变电站应急发电机组的发电机组结构组成、发电机组的选择、安全技术要求以及运行维护要求。 本文件适用于35 kV及以上电压等级变电站内安装的1 kV及以下、内燃机驱动的应急发电机组（简称发电机组）。换流站、发电厂内使用的发电机组可参照执行。 注：应急发电机组主要指变电站站用电源消失后，达到条件时启动发电机组进行应急供电，并带规定负载运行。

Technical specification for safety of emergency generating set in substation

T/CEEMA 0204-2023 增材制造激光熔覆层抗裂性能试验与评价技术规范

激光熔覆增材制造是一种先进的再制造技术，通过利用高能量的激光束，在对基体材料影响较小的情况下实现对基体的几何形状或力学性能的恢复或优化。为了追求熔覆涂层材料更高的强韧性，人们专注于其抗断裂的能力。根据经典的断裂力学理论，在非理想情况下，材料存在的缺陷在施加应力会发生断裂，并定义出断裂韧性用以衡量材料的抗断裂能力。在纳米到几微米的范围内的薄膜材料，常用的试验设备难以准确测量。随着仪器化纳米压入和计算机技术的迅速发展，采用纳米压痕仪已经成为纳米力学表征领域的主要手段。然而，利用该技术对材料抗断裂能力进行试验，容易受到仪器设备、样品材料、环境以及评价方法等众多因素的影响，这些影响因素导致对抗断裂性的评价标准难以统一。因此，迫切需要通过标准化来规范增材制造激光熔覆材料抗断裂试验。 目前，国内对纳米压痕技术的试验规范：《GB/T 22458-2008  仪器化纳米压入实验方法通则》《GB/T 25898-2010  仪器化纳米压入试验方法  薄膜的压入硬度和弹性模量》《GB/T 37900-2019  超薄玻璃硬度和断裂韧性试验方法小负荷维氏硬度压痕法》《NF A03-180-2006  金属材料平面应变断裂韧性的测定》《GB/T 25898-2010  仪器化纳米压入试验方法  薄膜的压入硬度和弹性模量》等。本标准的编写参考了上述标准的适用部分，本标准对薄膜材料的抗断裂能力和断裂韧性的表征方法和评价指标进行了标准化。

Technical specification for test and evaluation of crack resistance of high entropy alloy laser cladding

T/QGCML 2006-2023 蒸汽富能背压发电技术规程

本文件规定了蒸汽富能背压发电技术规程的术语和定义、原理、设备要求、管道工艺要求、电气要求、热力控制要求、防腐保温要求、系统验收。 本文件适用于蒸汽富能背压发电系统的设计及验收。

Technical regulations for steam-rich back-pressure power generation

ASTM D6224-23 辅助发电厂设备用润滑油在用监测的标准实施规程

Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment

T/CEEMA 02002-2023 风力发电机组螺栓预紧力在线监测技术规范

本标准规定了基于超声波测量的风力发电机组螺栓预紧力在线监测技术。 本标准适用于M6～M64的螺栓，夹持长度不小于3d。

Technical Specification for On-line Monitoring of Bolts of Wind Turbine

T/CEEIA 709-2023 水轮发电机组轴系稳定性劣化趋势预测技术导则

本文件提供了水轮发电机组（以下简称“机组”）轴系稳定性劣化趋势预测的方法、原则和要求。 本文件适用于机组轴系稳定性劣化趋势预测，适用于容量在100 MW以上的立式机组，抽水蓄能机组可参照执行。

Technical guide of predicting the trend of stability deterioration for Hydro-generator units shaft systems

T/HEBQIA 189-2023 火电机组用真空热管型低温省煤器

本标准规定了火电机组用真空热管型低温省煤器的术语和定义、技术要求、试验方法、检验规则、使用说明与标志、包装、运输和贮存。

Vacuum heat pipe type low temperature economizer for thermal power units

T/HEBQIA 181-2023 HP1203/Dyn磨煤机高挥发份煤操作技术规范

本文件规定了HP1203/Dyn磨煤机高挥发份煤操作技术规范的术语和定义、基本要求、工艺流程、准备工作、开车顺序、配烧调整、技术措施。

HP1203/Dyn Coal Mill High Volatile Coal Operation Technical Specifications

T/CNS 71-2022 高温气冷堆核动力厂金属监督技术规程

本文件规定了高温气冷堆核动力厂金属监督的部件范围、检验项目、内容及相应的技术要求。

Technical specification for metal supervision of high temperature gas cooled nuclear power plants

T/JSEPA 003-2022 燃气轮机组黑启动技术规范

本标准规定了燃气轮机组黑启动的总则、基本技术条件、黑启动试验、黑启动程序及应急处置。 本标准适用于燃气轮机组黑启动能力的建设。

Technical specification for black start of gas turbine unit

T/CICEIA /CAMS58-2022 以通用汽油机为动力的发电机组 排放限值及测试方法

本文件规定了以通用汽油机为动力的发电机组（以下简称发电机组）的排放限值和测试方法。 本文件适用于以工作容积小于1000cm3的通用汽油机为动力的发电机组。 其余技术内容见标准文本。

Generating sets powered by general gasoline engines -emission limits and test methods

NB/T 11030-2022 煤矿低浓度瓦斯发电机组通用要求

本文件适用于煤矿低浓度瓦斯发电机组的设计制造、瓦斯发电工程设计、安全评价、环境评价及项目验收，煤矿高浓度瓦斯发电机组可参照使用。

General requirements for coal mine low concentration gas generating units

ISO 8528-10:2022 往复式内燃机驱动的交流发电机组.第10部分:空气噪声的测量

This document specifies noise test codes for determining the sound power level and the emission sound pressure level at the workstation of reciprocating internal combustion engine driven electrical power generating sets. This document applies to constant and variable-speed reciprocating internal combustion (RIC) engine driven alternatingcurrent(AC) and directcurrent(DC) generatingsets for fixed and mobile applications with rigid or flexible mountings. It is applicable for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. NOTE 1 For some specific applications (e.g. essential hospital supplies, high-rise buildings) supplementary requirements can be necessary. The provisions of this document can be regarded as a basis. NOTE 2 This document is referenced with regard to noise in ISO 8528-13:2016, which contains requirements concerning the design of generating sets, verification of noise levels and information related to noise in the operating and maintenance instructions. 1.1 General X 1.2 Types of noise and noise sources X 1.3 Test environment X 1.4 Measurement uncertainty X 1.1 General X 1.2 Types of noise and noise sources X 1.3 Test environment X 1.4 Measurement uncertainty X

Reciprocating internal combustion engine driven alternating current generating sets — Part 10: Measurement of airborne noise

ISO 8528-5:2022 往复式内燃机驱动的交流发电机组.第5部分:发电机组

This document specifies design and performance criteria arising out of the combination of a reciprocating internal combustion (RIC) engine and an alternating current (AC) generator when operating as a unit. This unit can run in parallel to the grid or not. This document applies to AC generating sets driven by RIC engines for land and marine use, excluding generating sets used on aircraft, or to propel land vehicles and locomotives. For some specific applications (e.g. essential hospital supplies and high-rise buildings), supplementary requirements can apply. The provisions of this document are a basis for establishing any supplementary requirements. For generating sets driven by other reciprocating-type prime movers (e.g. steam engines), the provisions of this document can be used as a basis for establishing these requirements.

Reciprocating internal combustion engine driven alternating current generating sets — Part 5: Generating sets