共找到 275 条与 电阻器综合 相关的标准,共 19 页
This drawing describes the requirements for a high power, double tab resistor with a flange mount.
RESISTOR, FIXED, FILM, CHIP, FLANGE MOUNT, DOUBLE TAB, HIGH POWER 10 WATTS
This specification covers the general requirements for ceramic dielectric; variable capacitors intended for operation over a temperature range of -55°C to +85°C, for use in circuits where periodic adjustments are required
CAPACITORS, VARIABLE, CERAMIC DIELECTRIC, GENERAL SPECIFICATION FOR
Covers thick film general purpose rectangular leadless discrete fixed resistors with temperature coefficients of + 350 PPM/?C.
Resistors, Rectangular, Surface Mount, General Purpose
This drawing describes the requirements for a fixed, film, 0.25 watt, power curve C, precision resistor.
RESISTOR, FIXED, FILM, PRECISION, 0.25 WATT, POWER CURVE C
Effective 8 June 1972, MIL-DTL-3965 has been declared "Inactive for New Design" with no superseding specification. This is applicable on all acquisitons to which MIL-DTL-3965 is applied.
CAPACITOR, FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a fixed, film, 0.1 watt, power curve C, precision resistor.
RESISTOR, FIXED, FILM, PRECISION, 0.1 WATT, POWER CURVE C
Resistor network, fixed, film, style RN1082, detail specification for
This drawing describes the requirements for a beryllia substrate, high power, fixed film, chip resistor, style 1206.
RESISTOR, CHIP, FIXED, FILM, BERYLLIA SUBSTRATE, HIGH POWER, STYLE 1206
This drawing describes the requirements for a .120 by .060 chip resistor with low and high resistance values, a wide range of characteristics and tolerances.
RESISTOR, CHIP, FIXED, FILM, LOW AND HIGH VALUES, STYLE 1206
This drawing describes the requirements for a thermally sensitive resistor.
THERMISTOR, THERMALLY SENSITIVE RESISTOR
This drawing describes the specific electrical, mechanical, and environmental requirements for polymer cased hybrid capacitors.
CAPACITORS, TANTALUM, HYBRID, POLYMER CASE, SEALED
This handbook provides guidance in determining and prolonging the serviceability of aluminum electrolytic fixed capacitors during storage. This handbook is for guidance only. This handbook cannot be cited as a requirement. If it is, the contractor does not have to comply.
STORAGE SHELF LIFE AND REFORMING PROCEDURES FOR ALUMINUM ELECTROLYTIC FIXED CAPACITORS
This specification covers the general requirements for ceramic plate, single layer capacitors. These capacitors are intended for stripline or microstrip applications, usually at frequencies of 1 GHz and higher. Capacitors covered by this specification have failure rate levels (FRL) ranging from 1.0 to 0.001 percent per 1,000 hours. These failure rate levels are established at a 90-percent confidence level and maintained at a 10-percent producer’s risk. They are based on life tests performed at a maximum rated voltage at maximum rated temperature. An acceleration factor of 8:1 has been used to relate life test data obtained at 200 percent of rated voltage at maximum rated temperature, to rated voltage at rated temperature. Stat stical Process Control (SPC) techniques are required in the manufacturing process to minimize variation in production of capacitors supplied to the requirements of this specification.
CAPACITORS, CHIP, SINGLE LAYER, FIXED, PARALLEL PLATE, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
This drawing describes the requirements for a 1 watt, variable, panel mounted, resistor.
RESISTOR, VARIABLE, PANEL MOUNTED, 1 WATT
This drawing describes the requirements for a 10 pin, single-in-line package (SIP), resistor network with a ±100 ppm/OC temperature coefficient
RESISTOR NETWORK, 10-PIN, SINGLE-IN-LINE PACKAGE (SIP)
This drawing describes the requirements for an insulated, fixed, film resistor which exhibits low inductance over a frequency range of 1 MHz to 30 MHz.
RESISTOR, FIXED, FILM, INSULATED, LOW INDUCTANCE
This specification covers the general requirements for established reliability(ER) and nonestablished reliability(non-ER), mica dielectric, fixed capacitors(see 6.1).
CAPACITORS, FIXED, MICA DIELECTRIC, ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
This specification covers the general requirements for tantalum, electrolytic (nonsolid electrolyte), fixed capacitors (polarized and nonpolarized), hermetically and nonhermetically sealed (see 1.2.1.7) in metal cases; style CL67 and all tubular-foil styles are insulated (see 6.1). This specification also covers removable counting brackets for use with the CL55-series capacitors.
CAPACITOR, FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, GENERAL SPECIFICATION FOR
This supplement forms a part of MIL-C-62E, dated 2 February 2004
CAPACITORS, FIXED, ELECTROLYTIC (DC, ALUMINIM, DRY ELECTROLYTE, POLARIZED), GENERAL SPECIFICATION FOR
This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.
RESISTORS, FIXED, FILM (INSULATED), 1/2 WATT
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号