共找到 275 条与 电阻器综合 相关的标准,共 19 页
This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.
RESISTORS, FIXED, FILM (INSULATED), 1/8 WATT
This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.
RESISTORS, FIXED, FILM (INSULATED), 1 WATT
This drawing describes the requirements for an eight-pin, single inline package (SIP), resistor network.
RESISTOR NETWORK, 8-PIN, SINGLE INLINE PACKAGE
This specification covers the general requirements for polarized, dry-electrolyte, aluminum, direct current (dc), fixed capacitors for use in filter and bypass circuits where large excesses of capacitance over the nominal capacitance can be tolerated.
CAPACITORS, FIXED, ELECTROLYTIC (DC, ALUMINIM, DRY ELECTROLYTE, POLARIZED), GENERAL SPECIFICATION FOR
This specification covers the general requirements for direct current (dc) paper-dielectric, fixed capacitors hermetically sealed in metal cases, intended primarily for filter, by-pass, and blocking purposes where the alternating-current (ac) component of the impressed voltage is small with respect to the dc voltage rating.
CAPACITORS, FIXED, PAPER OR PLASTIC DIELECTRIC, DIRECT CURRENT, (HERMETICALLY SEALED IN METAL CASES), GENERAL SPECIFICATION FOR [Use In Lieu Of: DLA MIL-C-0025 B (1)]
This drawing, MIL-PRF-39014, and MIL-PRF-39014/5 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks.
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (4 CAPACITOR SECTIONS) BX
This drawing and MIL-PRF-20 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks.
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (4 CAPACITOR SECTIONS) CG
This drawing describes the requirements for aluminum oxide, electrolytic apacitors.
CAPACITORS, FIXED, ELECTROLYTIC POLARIZED, ALUMINUM OXIDE, ULTRA-LOW ESR
A-A-59497, dated 23 February 2000, has been reviewed and determined to be valid for use in acquisition
RESISTORS, VARIABLE, NONWIRE WOUND, WIRE WOUND, PRECISION, NONPRECISION, GENERAL REQUIREMENTS FOR
This drawing describes the requirements for tantalum hybrid capacitors, hermetically sealed in welded tantalum case with glass to metal anode terminal.
CAPACITORS, TANTALUM, HYBRID, HERMETICALLY SEALED
This drawing, MIL-PRF-39014, and MIL-PRF-39014/5 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (9 CAPACITOR SECTIONS) BX
This handbook is for guidance only and cannot be cited as a requirement. If it is, the contractor does not have to comply. This handbook consists of the following:
CAPACITORS, SELECTION AND USE OF
This drawing and MIL-PRF-83421 describes the requirements for PTFE (Teflon) dielectric capacitors.
CAPACITORS, FIXED, METALLIZED PTFE (TEFLON) DIELECTRIC, HERMTICALLY SEALED
This drawing, MIL-PRF-39014, and MIL-PRF-39014/5 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks.
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (7 CAPACITOR SECTIONS) BX
This drawing and MIL-PRF-20 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks.
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (8 CAPACITOR SECTIONS) CG
The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (8 CAPACITOR SECTIONS) BX
This drawing and MIL-PRF-20 describe the complete requirements for single-in-line packaged multilayer ceramic capacitor networks.
CAPACITORS, CERAMIC, SINGLE IN-LINE PACKAGE, NETWORK, (7 CAPACITOR SECTIONS) CG
This drawing describes the requirements for a 0.060 X 0.030 chip resistor of very low resistance values and a wide range of characteristics and tolerances.
RESISTOR, CHIP, FIXED, FILM, VALUES LESS THAN 1 OHM, STYLE 0603
This (CID) covers the general requirements for flameproof, fusible resistors. These resistors act as a wire-wound resistor and a fuse, and are used in applications where precise control of fusing point and time lags are necessary. These resistors eliminate fire hazard and circuit board damage due to overheated components.
RESISTORS, FLAMEPROOF, FUSIBLE
This drawing describes the requirements for a fixed, film, .020 X .010, zero-ohm, chip resistor.
RESISTOR, FIXED, FILM, CHIP, ZERO-OHM, STYLE 0201
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号