43.040.65 玻璃窗和刮水器 标准查询与下载

NF R19-601-1:2011 道路车辆.汽车上釉修补推荐性操作规程.第1部分:冲击修复准则

Road vehicles - Recommendation for motor vehicle glazing repair - Part 1 : Criteria for impact repair.

DIN 52310-2:2011 道路车辆用安全玻璃材料的人头模型撞击试验.第2部分:减速测量试验

Headform impact test on safety glazing materials for road vehicles - Part 2: Test with deceleration measurement

BS ISO 4513:2010 道路车辆.能见度.驾驶员眼睛位置的眼睛活动范围的确定方法

Road vehicles - Visibility - Method for establishment of eyellipses for driver's eye location

ISO 4513:2010 道路车辆.能见度.驾驶员眼睛位置的眼睛活动范围的确定方法

Road vehicles - Visibility - Method for establishment of eyellipses for driver's eye location

SAE J216-2010 汽车玻璃电路

This SAE Recommended Practice establishes limits for electrical circuits on motor vehicle safety glazing materials.

Motor Vehicle Glazing Electrical Circuits

SAE J2802-2010 盲点监测系统(BSMS):操作特性和用户界面

This document specifies the minimum recommendations for Blind Spot Monitoring System (BSMS) operational characteristics and elements of the user interface. A visual BSMS indicator is recommended. BSMS detects and conveys to the driver via a visual indicator the presence of a target (e.g., a vehicle), adjacent to the subject vehicle in the "traditional" Adjacent Blind Spot Zone (ABSZ). The BSMS is not intended to replace the need for interior and exterior rear-view mirrors or to reduce mirror size. BSMS is only intended as a supplement to these mirrors and will not take any automatic vehicle control action to prevent possible collisions. While the BSMS will assist drivers in detecting the presence of vehicles in their ABSZ, the absence of a visual indicator will not guarantee that the driver can safely make a lane change maneuver (e.g., vehicles may be approaching rapidly outside the ABSZ area). This document applies to original equipment and aftermarket BSMS systems for passenger vehicles. This document does not apply to installing a BSMS on either motorcycles or commercial vehicles. Finally, this document does not address Lane Change Warning systems, which monitor areas substantially farther back than the side blind spot areas monitored by the BSMS (See ISO FDIS 17387).

Blind Spot Monitoring System (BSMS): Operating Characteristics and User Interface

SAE J985-2009 后视镜设计中视觉因素考虑

The design and location of rear viewing mirrors or systems, and the presentation of the rear view to the driver can be best achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.

Vision Factors Considerations in Rear View Mirror Design

SAE J964-2009 镜子模糊度和反射度的测量用推荐实施规程

This SAE Recommended Practice describes methods for determining total and specular reflectance for mirrors with flat and curved surfaces and a method for determining diffuse reflectance and haze for mirrors with flat surfaces.

Recommended Practice for Measuring Haze and Reflectance of Mirrors

SAE J381-2009 卡车、公共汽车和多用途汽车的挡风玻璃防霜系统试验规程和性能要求

This SAE Recommended Practice establishes uniform test procedures and performance requirements for the defrosting system of enclosed cab trucks, buses, and multipurpose vehicles. It is limited to a test that can be conducted on uniform test equipment in commercially available laboratory facilities. Current engineering practice prescribes that for laboratory evaluation of defroster systems, an ice coating of known thickness be applied to the windshield and left- and right-hand side windows to provide more uniform and repeatable test results, even though under actual conditions such a coating would necessarily be scraped off before driving. The test condition, therefore, represents a more severe condition than the actual condition, where the defroster system must merely be capable of maintaining a cleared viewing area. Because of the special nature of the operation of most of these vehicles (where vehicles are generally kept in a garage or warmed up before driving) and since defrosting under steady-state over-the-road operations is the main concern, test conditions have been adopted which assume that the engine is warm before the vehicle is driven. There are two options for producing hot coolant in this recommended practice. Testing using these two approaches on the same vehicle will not necessarily provide identical results. Many vehicle models are offered with optional engines, and each engine has varying coolant temperatures and flow rates. If the test is being conducted to compare the performance of one defroster design to another defroster design, then the external coolant source approach (Test A) will yield the most comparable results. If the test is being conducted to validate the defroster installation on a specific vehicle model with a specific engine, then using the engine to heat the coolant (Test B) will be more appropriate. This document will be reviewed and revised as technological progress in vehicle defroster test procedure requires.

Windshield Defrosting Systems Test Procedure and Performance Requirements Trucks, Buses, and Multipurpose Vehicles

KS R ISO 9619:2007 客车.挡风玻璃刮水系统.试验方法.

이 규격은 승용차에(KS R ISO 3833의 3.1.1 참조) 설치되어 있는 앞 유리창

Passenger cars－Windscreen wiping systems－Test method

KS R ISO 9619-2007(2022) 乘用车－挡风玻璃刮水系统－试验方法

Passenger cars－Windscreen wiping systems－Test method

KS R ISO 9619-2007(2017) 乘用车挡风玻璃擦拭系统试验方法

Passenger cars－Windscreen wiping systems－Test method

KS R ISO 3468:2007 客车.轿车的挡风玻璃除霜装置.试验方法

이 규격은 승용차(KS R ISO 3833의 3.1.1)에 적합한 앞 유리창 성에 제거 장

Passenger cars－Windscreen defrosting systems－Test method

CAS 140-2007 玻璃安全膜技术规范

本规范规定了玻璃安全膜(车用和建筑用)的性能要求与技术规范。 本规范适用于车用和建筑用玻璃安全膜。

Technical Criterions for Glass Safety Protective Film

CAS 142-2007 建筑玻璃窗膜技术规范

本标准规定了建筑玻璃窗膜的技术要求和试验方法、建筑玻璃贴膜工艺技术条件、质量要求，标志、包装和贮存。 本标准适用于建筑玻璃窗内侧贴膜，也适用于建筑玻璃贴膜工艺和质量要求。

Technical Criterions for Building Window Film

ISO 3469:1989/Amd 1:2006 乘用车.挡风玻璃清洗系统.试验方法.修改件1

Passenger cars — Windscreen washing systems — Test methods — Amendment 1

VDA 2020-2006 汽车上光.玻璃厚度

Automotive Glazin - Glass Thickness

SANS 20043:2005 关于安全玻璃材料及其在车辆上安装的批准的统一规定

Applies to safety glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers, and to the fitting thereof, to the exclusion, however, of glazing for lighting and light-signall

Uniform provisions concerning the approval of safety glazing materials and their installation on vehicles

TIS 954-2005 后视镜

Rear.view mirrors

SAE J673-2005 汽车安全玻璃

This SAE Recommended Practice is intended to cover current safety glazing practice applicable to safety glasses for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are included principally for the guidance of body engineers and designers. For additional information on safety glazing materials for use in motor vehicles and motor vehicle equipment, see SAE J674.

Automotive Safety Glasses