43.040.65 玻璃窗和刮水器 标准查询与下载

SANS 10240:2005 机动车辆替换安全玻璃的无窗框安装法安装

Specifies requirements for replacement auto glass in motor vehicles by means of the direct glazing method.

The installation of replacement auto glass in motor vehicles by the direct glazing method

SAE J100-2005 A类机动车玻璃门窗遮光条

This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.

Class A Vehicle Glazing Shade Bands

DIN 52230:2004 车辆玻璃窗用安全玻璃结构的抗强行进入性的测定.玻璃门窗系统试验

The test methods are designed to assess levels of resistance against forced entry provided by safety glazing used in vehicles.

Determination of resistance to forced entry of safety glass constructions used in vehicle glazing - Test of glazing systems

GSO 1680:2003 汽车：配备无铅汽油发动机的汽车排放的气态环境污染物的允许限值

This standard is concerned with the allowable limits of gaseous pollutants emitted to the atmosphere from new unleaded gasoline engined vehicles, whose maximum weight does not exceed 3500 kg.

Motor Vehicles - Allowable Limits Of Gaseous Pollutants Emitted To The Atmosphere From Unleaded Gasoline Engined Vehicles

GSO 1684:2003 汽车：装有无铅汽油发动机的汽车向环境排放气态污染物的测试方法 第4部分：曲轴箱排放气态污染物的估算方法

This standard is concerned with the methods for determination of gaseous pollutants emitted from crankcase of unleaded gasoline engined vehicles.

MOTOR VEHICLES METHODS OF TEST FOR GASEOUS POLLUTANTS EMITTED FROM UNLEADED GASOLINE ENGINED VEHICLES - PART 4: DETERMINATION OF GASEOUS POLLUTANTS EMITTED FROM ENGINE CRANKCASE

GSO 1677:2003 汽车 多层安全玻璃

This standard is concerned with laminated safety glass for use as windscreens or other windows in motor vehicles.

MOTOR VEHICLES - LAMINATED SAFETY GLASS

GSO 1681:2003 汽车 装有无铅汽油发动机的汽车排放气态环境污染物的测试方法： 第1部分 冷态启动后排气中气态污染物的估算方法

This standard is concerned with the method for determination of gaseous pollutants, emitted in the exhaust gases of unleaded gasoline engined vehicles, after a cold start using urban cycle and extra-urban cycle

Motor Vehicles – Methods Of Test For Gaseous Pollutants Emitted From Unleaded Gasoline Engined Vehicles – Part 1: Determination Of Exhaust Gaseous Pollutants After A Cold Start

ISO 4513:2003 道路车辆.能见度.驾驶员眼睛位置的眼睛活动范围的确定方法

This International Standard specifies a method for establishing an eyellipse for locating driver's eyes inside a road vehicle for the purpose of measuring the driver's field of view. Elliptical (eyellipse) models in both two and three dimensions are used to represent 95th and 99th percentiles of driver eye locations. Its procedures, which differ depending on the type of vehicle considered, are applicable to passenger cars (and light trucks), and to buses and heavy vehicles, as defined in ISO 3833. The statistical representation of the driver's eye locations it provides can be used as a design tool for passenger cars (although V-points can be used in lieu of the complete eyellipse to standardize the driver's field of view for regulation purposes).

Road vehicles - Visibility - Method for establishment of eyellipses for driver's eye location

SAE J902-2003 客车前车玻璃除霜系统

This SAE Recommended Practice provides a test procedure and performance guideline for evaluating passenger car windshield defrosting systems. It is limited to results of tests that can be conducted on uniform test equipment in commercially available laboratory facilities. The current engineering practice prescribes that for laboratory evaluation of defroster systems, a known quantity of water shall be sprayed on the windshield to form an ice coating and then melted by the defroster under specific vehicle operating conditions. The procedure provides uniform and repeatable laboratory test results, even though under actual conditions such a coating would be removed by scraping before driving the vehicle. The performance obtained, therefore, does not directly relate to actual driving conditions, but services as a laboratory performance indicator for comparing test results within or between systems. This document is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances and this should be kept in mind when considering its use.

Passenger Car Windshield Defrosting Systems

SAE J198-2003 挡风玻璃刮水器系统.卡车,公交车,多用途车

This SAE Recommended Practice establishes for trucks, buses, and multipurpose passenger vehicles with GVW of 4500 kg (10 000 lb) or greater: a.) Minimum performance requirements for windshield wiping systems; b.) Uniform test procedures that include those tests that can be conducted on uniform test equipment by commercially available laboratory facilities; c.) Uniform terminology of windshield wiper system characteristics and phenomena consistent with those found in guides for the use of engineering layout studies to evaluate system performance; and d.) Guides for the design and location of components of the systems for function, servicing of the system, etc. The test procedures and minimum performance requirements, outlined in this document, are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed.

Windshield Wiper SystemsTrucks, Buses, and Multipurpose Vehicles

DIN ISO 3917:2003 道路车辆.安全玻璃材料.耐辐射、耐高温、耐湿度、耐燃烧和模拟气候的试验方法

Road vehicles - Safety glazing materials - Test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering (ISO 3917:1999)

DIN ISO 3538:2003 道路车辆.安全玻璃窗材料.光学性能试验方法

This standard specifies optical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.#,,#

Road vehicles - Safety glazing materials - Test methods for optical properties (ISO 3538:1997)

DIN 52298-2:2003 道路车辆.汽车防撞安全玻璃散射光测量.第2部分.映射法

The document describes a method for the measurement of scattered light of a pane to be tested under a small angle to the optical axis. The method is applicable for plane and bended safety glazing materials for vehicle glazing also when the pane is installed, especially windscreens.#,,#

Road vehicles - Measurement of scattered light of safety glazing materials for vehicle glazing - Part 2: Image-mapping method

SAE J964-2003 测量镜面雾度和反射率的推荐做法

This SAE Recommended Practice describes methods for determining total and specular reflectance for mirrors with flat and curved surfaces and a method for determining diffuse reflectance and haze for mirrors with flat surfaces.

Recommended Practice for Measuring Haze and Reflectance of Mirrors

SAE J1246-2003 测量凸镜的曲率半径

This SAE Recommended Practice is intended for use in measuring the radius of curvature (ROC) of spherical convex mirror.

Measuring the Radius of Curvature of Convex Mirrors

SAE J985-2002 后视镜设计中视觉因素的考虑

The design and location of rear viewing mirrors or systems, and the presentation of the rear view to the driver can be best achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.

Vision Factors Considerations in Rearview Mirror Design

AS 4739:2002 直装式汽车玻璃替换．轻型车辆

Specifies the procedure for direct glazed automotive glass replacement.

Direct glazed automotive glass replacement - Light vehicles

ISO 9619:1992/Amd 1:2002 客车.挡风玻璃刮水系统.试验方法.修改件1

This is Amendment 1 to ISO 9619-1992 (Passenger cars — Windscreen wiping systems — Test method AMENDMENT 1 )

Passenger cars - Windscreen wiping systems - Test methods; Amendment 1

DIN 72786-1:2001 公路车辆风挡刮水器系统.弧刷臂.第1部分:挂钩固定用A型刮水器刮板

The following items are covered: Dimensions and materials.

Windscreen wiper systems for road vehicles - Wiper arm - Part 1: Type A wiper blades for hook fastening

ISO 9259:1991/Amd 1:2001 乘用车 风挡玻璃刮刷系统 刷臂与刮水片的连接 修改1

This is Amendment 1 to ISO 9259-1991 (Passenger cars — Windscreen wiper systems — Wiper arm-to-blade connections)

Passenger cars - Windscreen wiper systems - Wiper arm-to-blade connections; Amendment 1