43.040.65 玻璃窗和刮水器 标准查询与下载

DIN 52310-2:1991 带缓冲测量的车辆安全玻璃人头模型撞击试验

The standard describes the headform impact test for testing the behaviour of safety glasses (toughened glass, laminated glass, plastics and glass-plastics-laminates) for a road vehicles under impact from a blunt bulky object. The dropping object is a 5 kg or 10 kg phantom head fitted with receivers for acceleration. The damage of the sample, if any, acceleration data measured and the falling height of the phantom head, applied according to the requirements, are noted and recorded as test results. The test results allow an estimation of the protection of the human head provided by the safety glazing materials for head injuries in case of an impact on the safety glazing.

Headform impact test on safety glazing materials for road vehicles with decleration measurement

ISO 9704:1990 乘用车 刮刷系统 轴端和臂孔

Specifies the main dimensions and general requirements for wiper arm to shaft end connections of wiper systems. Gives the preferred type 1; the normative annex A includes the non-preferred type 2.

Passenger cars; wiper systems; shaft ends and arm-holes

DIN 72786-2:1990 汽车挡风玻璃刮水器.雨刮臂.螺丝固定C型刮水片

This standard applies to wiper blades with screw fastening for the use at windscreen and rear window wiper systems of road vehicles and contains dimensions required for interchangeability.

Windscreen and rear window wiper systems for road vehicles; wiper arm and blade assembly; type C wiper blade for screw fastening

DIN 52307:1990 车辆安全玻璃沸水试验

This standard describes the dart drop test of safety glass for vehicle glazing. Its purpose is to determine the behaviour of the safety glass under impact from pointed objects. After the dart drop test the type and extent of fracturing is determined.

Dart drop test on safety glass for vehicle glazing

DIN 52306:1990 车辆安全玻璃落球试验

This standard describes the 227-g and the 2260-g ball drop tests for safety glazing materials for road vehicles. The purpose of both ball drop tests is to determine the behaviour of the safety glass under impact from blunt objects. After the ball drop test the type and extent of fracturing is determined.

Ball drop test on safety glass for vehicle glazing

ISO 3470:1989 乘用车 风挡玻璃除雾系统 试验方法

Specifies the test procedure for systems when these are fitted; Does not specify reference areas or levels of performance; The annex A is for information only. This second edition cancels and replaces the first edition (1976).

Passenger cars - Windscreen demisting systems - Test method

ISO 3469:1989 乘用车 风挡玻璃清洗系统 试验方法

Specifies the test procedure for systems when these are fitted; Does not specify reference areas or levels of performance. The annexes A,B and C are an integral part of it, annex D is for information only. This second edition cancels and replaces the first edition (1975).

Passenger cars; windscreen washing systems; test methods

ISO 3468:1989 乘用车 风挡玻璃除霜系统 试验方法

Specifies the test procedure for systems when these are fitted. Does not specify reference areas or levels of performance. The annexes A and B are for information only. This second edition cancels and replaces the first edition (1976).

Passenger cars; windscreen defrosting systms; test methods

ISO 9258:1989 乘用车 刮刷系统 刮水片长度

Establishes two ranges of lengths for wiper blades for passenger cars, to be used as a guide for their selection. Table 1 gives a short (350, 400, 450, 500, 550, 600, 650, 700 mm) and an extended list (from 250 up to 700 mm) of wiper blade lengths, which may serve as a guide for choice of wiper blades.

Passenger cars; wiper systems; wiper blade length

SNI 09-1401-1989 机动车凸面反射镜. 反射性能测试方法

Rear reflecting mirror for motor vehicles, Test method for reflectance

NF R14-501:1988 道路车辆.乘用车后窗除雾装置.试验方法

Road vehicles. Rear-window demisting system for passenger cars. Test method.

NF R14-502:1988 道路车辆.乘用车后窗除冰装置.试验方法

Road vehicles. Rear-window defrosting system for passenger cars. Test method.

SAE J1907-1988 玻璃与汽车玻璃封装用弹性材料的剥离粘性试验

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass. This test method suggests that elastomeric material of less than 172 MPa modulus be used as the encapsulating material. The present practice of encapsulating automotive glass is described as molded-in-place elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with the cured elastomeric material bonded to the perimeter of the glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.

Peel Adhesion Test for Glass to Elastomeric Material for automotive glass Encapsulation

DIN 52310:1986 车辆安全玻璃模拟跌落试验

This standard describes the headform impact test for testing the behaviour of safety glasses (toughened glass, laminated glass, plastics and glassplastics-laminates) in a road vehicle under impact from a blunt bulky object. The dropping object is a headform weight (10 kg) with a spherical or semi-spherical head made of laminated hard wood covered with a replaceable felt and with a cross-beam made of wood. Between the spherical part and the cross-beam, there is a neck-shaped intermediate piece and on the other side of the cross-beam, a mounting rod. The damage of the sample, if any, and the falling height of the headform weight, applied according to the requirements, are noted an recorded as test results.

Headform impact test on safety glass for vehicle glazing

NF R14-409:1984 道路车辆.后视镜.测定反射率的试验方法

Road vehicles. Rear view mirrors. Test method for determining reflectance.

DIN 52308:1984 安全玻璃蒸煮试验

Boil test on laminated glass

BS AU 182:1982 道路车辆用塑料安全防碎玻璃窗材料规范

Specifies requirements and tests for plastics safety glazing for motor vehicles and trailers, e.g. windows, partitions, rooflights and wind deflectors. Does not specify mounting methods.

Specification for plastics safety glazing materials for use in road vehicles

ISO 5740:1982 道路车辆 后视镜 测定反射率的试验方法

Specifies a test method for determining the reflectance of rear view mirrors. Applies to flat and convex surface mirrors intended for internal and external mounting. Describes the apparatus and the procedure with a direct and an indirect calibration method. This second edition cancels and replaces the first edition (1978).

Road vehicles; Rear view mirrors; Test method for determining reflectance

BS AU 170:1979 后视镜反射率的测量方法

This British Standard specifies a test method for determin-ing the reflectance of rear-view mirrors for road vehicles. It applies to flat and convex surface mirrors intended for internal and external mounting.

Methods for measurement of reflectance of rear view mirrors

SAE J1203-1977 汽车挡风玻璃安全镀锌材料的透光率推荐实施规程.1977年8月

The purpose of this test is to determine the light transmittance of automotive windshield safety glazing materials positioned at the angle of installation.

Light Transmittance of Automotive Windshields Safety Glazing Materials, Recommended Practice August 1977