43.060.40 标准查询与下载

ISO/CD 19880-7:2023 气态氢 加油站 第 7 部分：橡胶 O 形圈

Gaseous hydrogen — Fuelling stations — Part 7: Rubber O-rings

ISO/CD 19880-6:2023 气态氢 加油站 第 6 部分：配件

Gaseous hydrogen — Fueling stations — Part 6: Fittings

ISO/CD 19880-9:2023 气态氢 加氢站 第 9 部分：燃料质量分析取样

Gaseous hydrogen — Fuelling stations — Part 9: Sampling for fuel quality analysis

ISO/DIS 19880-2:2023 气态氢 加油站 第 2 部分：分配器和分配系统

Gaseous hydrogen — Fuelling stations — Part 2: Dispensers and dispensing systems

23/30415179 DC BS ISO 24605 道路车辆 带压力平衡端口的二甲醚 (DME) 加油连接器

BS ISO 24605. Road vehicles. Dimethyl Ether (DME) refuelling connector with pressure equalization port

BS ISO 19438:2023 用于内燃机的柴油和汽油过滤器 使用颗粒计数和污染物截留能力来确定过滤效率

1   Scope This document specifies a multi-pass filtration test, with continuous contaminant injection and using the on line particle counting method, to evaluate the performance of diesel fuel and petrol filters for internal combustion engines submitted to a constant flow rate of test liquid. The test procedure determines the contaminant capacity of a filter, its particulate removal characteristics and differential pressure. This document is applicable to filter elements having a rated flow between 50 l/h and 800 l/h; however, by agreement between the filter manufacturer and customer, and with some modifications, the procedure is permitted for application to fuel filters with higher flow rates.

Diesel fuel and petrol filters for internal combustion engines. Filtration efficiency using particle counting and contaminant retention capacity

BS ISO 20766-21:2023 公路车辆 液化石油气 (LPG) 燃料系统组件 压力和/或温度传感器

1   Scope This document specifies general requirements for the pressure and/or temperature sensors liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in t...

Road vehicles. Liquefied petroleum gas (LPG) fuel system components - Pressure and/or temperature sensors

BS ISO 20766-7:2023 公路车辆 液化石油气 (LPG) 燃料系统组件 带溢流阀的远程控制维修阀

1   Scope This document specifies general requirements and definitions of the liquefied petroleum gas fuel component: remotely controlled service valve with excess flow valve. This component is intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 84...

Road vehicles. Liquefied petroleum gas (LPG) fuel system components - Remotely controlled service valve with excess flow valve

BS ISO 20766-15:2023 公路车辆 液化石油气 (LPG) 燃料系统组件 溢流阀

1   Scope This document specifies general requirements of the liquefied petroleum gas fuel component, excess flow valve, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate facto...

Road vehicles. Liquefied petroleum gas (LPG) fuel system components - Excess flow valve

BS ISO 20766-8:2023 公路车辆 液化石油气 (LPG) 燃油系统组件 燃油泵

1   Scope This document specifies general requirements for the fuel pump component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document....

Road vehicles. Liquefied petroleum gas (LPG) fuel system components - Fuel pump

BS ISO 15500-21:2023 公路车辆 压缩天然气 (CNG) 燃料系统组件 排放管线关闭

1   Scope This document specifies tests and requirements for discharge lines closures, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403‑1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

Road vehicles. Compressed natural gas (CNG) fuel system components - Discharge line closures

BS ISO 15500-13:2023 公路车辆 压缩天然气(CNG)燃料系统组件 泄压装置（PRD）

1   Scope This document specifies tests and requirements for the pressure relief device (PRD), a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403‑1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

Road vehicles. Compressed natural gas (CNG) fuel system components. Pressure relief device (PRD)

ISO 19438:2023 内燃机用柴油燃料和汽油过滤器.用粒子计数及污物滞留量评定过滤效率

This document specifies a multi-pass filtration test, with continuous contaminant injection and using the on line particle counting method, to evaluate the performance of diesel fuel and petrol filters for internal combustion engines submitted to a constant flow rate of test liquid. The test procedure determines the contaminant capacity of a filter, its particulate removal characteristics and differential pressure. This document is applicable to filter elements having a rated flow between 50 l/h and 800 l/h; however, by agreement between the filter manufacturer and customer, and with some modifications, the procedure is permitted for application to fuel filters with higher flow rates.

Diesel fuel and petrol filters for internal combustion engines — Filtration efficiency using particle counting and contaminant retention capacity

ISO 20766-15:2023 道路车辆.液化石油气（LPG）燃料系统部件.第15部分：溢流阀

This document specifies general requirements of the liquefied petroleum gas fuel component, excess flow valve, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 15: Excess flow valve

ISO 20766-7:2023 道路车辆.液化石油气（LPG）燃料系统部件.第7部分：带溢流阀的远程控制工作阀

This document specifies general requirements and definitions of the liquefied petroleum gas fuel component: remotely controlled service valve with excess flow valve. This component is intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 7: Remotely controlled service valve with excess flow valve

ISO 20766-8:2023 道路车辆.液化石油气（LPG）燃料系统部件.第8部分：燃料泵

This document specifies general requirements for the fuel pump component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 8: Fuel pump

ISO 20766-21:2023 道路车辆.液化石油气（LPG）燃料系统部件.第21部分：压力和/或温度传感器

This document specifies general requirements for the pressure and/or temperature sensors liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to device which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 21: Pressure and/or temperature sensors

ISO 15500-13:2023 道路车辆 压缩天然气（CNG）燃料系统部件 第13部分：减压器（PRD）

This document specifies tests and requirements for the pressure relief device (PRD), a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD)

ISO 15500-21:2023 道路车辆.压缩天然气（CNG）燃料系统部件.第21部分：排放管线封闭

This document specifies tests and requirements for discharge lines closures, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with the ISO 15403-1. It is not applicable to the following: a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer; b) fuel containers; c) stationary gas engines; d) container-mounting hardware; e) electronic fuel management; f) refuelling receptacles.

Road vehicles — Compressed natural gas (CNG) fuel system components — Part 21: Discharge line closures

ISO/DIS 19880-9:2023 气态氢 加氢站 第 9 部分：燃料质量分析取样

Gaseous hydrogen — Fuelling stations — Part 9: Sampling for fuel quality analysis