43.080.01 商用车辆综合 标准查询与下载



共找到 322 条与 商用车辆综合 相关的标准,共 22

本本文件规定了纯电动智能跟随环卫车的术语、定义、技术要求和出厂检验要求。本文件适用于纯电动智能跟随环卫车。

Technical specifications of electric intelligent following sanitation vehicle

ICS
43.080.01
CCS
C361
发布
2021-12-31
实施
2021-12-31

本文件规定了电动道路车辆用超级电容器(电化学电容器)的要求、试验方法、检验规则、标志、包装、运输和贮存。(章节号对应) 本文件适用于电动道路车辆用超级电容器(以下简称“电容器”)单体、模块和系统。

Ultracapacitor for electric vehicles

ICS
43.080.01
CCS
C3670
发布
2021-09-15
实施
2022-10-17

ISO 18375:2016 describes an open-loop test method for determining the yaw stability of a vehicle on a low friction road surface. It applies to heavy vehicles, that is commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4). The method is intended for vehicles equipped with electronic yaw-stability control systems. As the results of this test depend largely on local and temporary changes in road surface friction, this International Standard gives recommendations about keeping the friction level as uniform as possible for good reproducibility of the test results.

Heavy commercial vehicles and buses — Test method for yaw stability — Sine with dwell test

ICS
43.080.01
CCS
发布
2021-07-01
实施

Heavy commercial vehicles and buses. Vehicle dynamics simulation and validation. Closing-curve test

ICS
43.080.01
CCS
发布
2021-06-16
实施
2021-06-16

本文件规定了电动汽车用动力蓄电池的健康状态评价指标计算方法、试验条件、试验方法、估算误差测试方法及检验规则。 本文件适用于电动汽车用锂离子动力蓄电池单体、系统及其管理系统,其他类型动力蓄电池及其管理系统可参照执行。

Evaluation index and estimation error test method of state of health for power battery for electric vehicles

ICS
43.080.01
CCS
C3670
发布
2021-05-06
实施
2022-06-14

This document specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle according to closing-curve tests as specified in ISO 11026. The purpose of the validation is to demonstrate that the vehicle dynamics simulation, combined with an integrated electronic stability control (ESC) system, can predict the roll and yaw stability behaviour of a physical vehicle, including the ESC system interventions, during a closing-curve test. The simulation method can be either hardware-in-the-loop [with the original electronic control unit (ECU) on a HiL test stand] or software-in-the-loop, based on a software code generated from the same source as for the ECU in the real vehicle. This document applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with a maximum weight above 3,5 tonnes and buses and articulated buses with a maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4).

Heavy commercial vehicles and buses - Vehicle dynamics simulation and validation - Closing-curve test

ICS
43.080.01
CCS
发布
2021-05-00
实施

Methanol fuel vehicle technical conditions

ICS
43.080.01
CCS
T47
发布
2021-03-05
实施
2021-07-01

Methanol vehicle fuel system technical conditions

ICS
43.080.01
CCS
T47
发布
2021-03-05
实施
2021-07-01

1范围 2规范性引用文件 3术语和定义 4符号 5要求 5.1单体锂离子电池 5.2锂离子电池模组 6可靠性快速评价 6.1电池潜在故障与可靠性评价定义 6.2试验条件 6.3潜在故障类型及其诊断

Specification for rapid reliability assessment of power battery system

ICS
43.080.01
CCS
C3670
发布
2021-01-12
实施
2021-01-14

本文件规定了在动力系统台架上进行插电式混合动力乘用车实际运行工况能量消耗量试验的试验方法。 本文件适用于最大设计总质量不超过3.5t的M1类、M2类和N1类、装用于点燃式发动机或压燃式发动机的、可外接充电的混合动力车辆,纯电动乘用车可参照执行。

Bench test method for energy consumption of plug-in hybrid passenger car powertrain

ICS
43.080.01
CCS
C3620
发布
2020-12-25
实施
2020-12-25

Heavy commercial vehicles and buses-Steady-staterollover threshold-Tilt-table test method

ICS
43.080.01
CCS
发布
20201221
实施
20201221

Road vehicles-Heavy commercial vehicles and buses-Steady-state circular tests

ICS
43.080.01
CCS
发布
20201221
实施
20201221

Road vehicles-Heavy commercial vehicles and buses-Lateral transient response test methods

ICS
43.080.01
CCS
发布
20201221
实施
20201221

Road vehicles-Vehicle dynamics test methods-Part 2:General conditions for heavy vehicles and buses

ICS
43.080.01
CCS
发布
20201221
实施
20201221

本文件规定了燃料电池电动汽车车载供氢系统振动试验的技术要求、设备要求及试验方法。 本文件适用于工作压力不超过70MPa、整体框架式、包含单个或多个压缩氢气储存瓶的燃料电池电动汽车的车载供氢系统。

Technical requirements for vibration test of on board hydrogen supply system of fuel cell electric vehicle

ICS
43.080.01
CCS
C3670
发布
2020-12-10
实施
2021-01-27

本文件按照GB/T 1.1-2020《标准化工作导则 第1部分 标准化文件的结构和起草规则》的规定起草,从建筑垃圾运输安全性、运输装备安全性出发,进一步完善和明确建筑垃圾车安全技术功能和性能指标要求。

Safety technical specifications for construction garbage trucks

ICS
43.080.01
CCS
G543
发布
2020-12-04
实施
2021-02-03

本规范规定了电动汽车用锂离子动力电池单体的安全性加速评价方法,主要内容包括对锂离子动力 电池进行加速循环老化测试,并提出其安全性的加速评价方法。

Specifications for rapid evaluation of power battery life cycle safety

ICS
43.080.01
CCS
C3670
发布
2020-10-30
实施
2020-11-09

本标准规定了48V锂离子启停电池包及系统(以下简称锂电池总成)的性能要求及测试方法,性能要求包括电气性能、安全性能、环境性能。 本标准主要适用于装载在电动汽车上的48V锂离子启停电池包及系统,主要以高功率应用为目的锂离子蓄电池包及系统。

48V lithium-ion start-stop battery pack and system test method

ICS
43.080.01
CCS
C3670
发布
2020-10-30
实施
2020-11-09

What is ISO 21308 ‑ 3 about?    ISO 21308 is a series of international standards on-road vehicles that discusses the specifications and parameters of the product . ISO 21308 ‑ 3 is the third part of the ISO 21308 series of documents applicable to chassis and bodywork manufacturers (BEP) providing guidance for understanding and mastering the different product data exchange formats for users providing a platform for efficient communication between the parties.    ISO 21308 ‑ 3

Road vehicles. Product data exchange between chassis and bodywork manufacturers (BEP) - General, mass and administrative exchange parameters

ICS
43.080.01
CCS
发布
2020-09-30
实施
2020-09-30

What is ISO 21308-2 about?    ISO 21308 is a series of international standards on-road vehicles that discusses the specifications and parameters of the product. ISO 21308-2 is the second part of the ISO 21308 series of documents applicable to truck chassis and bodywork manufacturers (BEP) providing guidance for understanding and mastering the different product data exchange formats for users providing a platform for efficient communication between the parties.    ISO 21308-2 provides a set of codes for the exchange of dimensional data between truck chassis manufacturers and bodywork manufacturers. The codes can be communicated via, for example, spreadsheet or XML.   The process of exchanging the above informati...

Road vehicles. Product data exchange between chassis and bodywork manufacturers (BEP) - Dimensional bodywork exchange parameters

ICS
43.080.01
CCS
发布
2020-09-30
实施
2020-09-30



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号