49.025.99 其他材料 标准查询与下载

SAE AMS5608F-2010 溶解热处理40Co 22Cr 22Ni 14.5W 0.07La耐腐蚀耐热钴合金片材,带材和板材

This specification covers a corrosion and heat resistant cobalt alloy in the form of sheet, strip, and plate. These products have been used typically for formed and drawn parts requiring high strength up to 1800 °F (982 °C) and oxidation resistance up to 2000 °F (1093 °C), but usage is not limited to such applications.

Cobalt Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 40Co - 22Cr - 22Ni - 14.5W - 0.07La Solution Heat Treated (UNS R30188)

SAE AMS5410B-2010 熔模铸造法1 Ni 16 Cr 8.5 Co 1.8 Mo 2.6 W 0.85 Cb 3.4 Ti 1.8 Ta 3.4 A1 0.010 B 0.05 Zr真空融化,真空铸造铸铁,或固溶处理,或溶液和沉淀硬化的耐腐蚀和耐热镍合金

This specification covers a corrosion and heat resistant nickel alloy in the form of investment castings. These castings have been used typically for parts, such as turbine blades or vanes, requiring good strength and hot corrosion resistance to 1800 °F (980 °C), but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat Resistant, Investment Castings 61Ni - 16Cr - 8.5Co - 1.8Mo - 2.6W - 0.85Cb - 3.4Ti - 1.8Ta - 3.4Al - 0.010B - 0.05Zr Vacuum Melted, Vacuum Cast As Cast, or Solution Treated, or Solution and Precipitation Hardened

SAE AIR5919A-2010 镉电镀层备选方案

This SAE Aerospace Information Report (AIR) is intended to document and provide access to information obtained by an industry survey. It summarizes and documents data regarding possible alternatives to the use of cadmium plating on general connectors and connector accessories typically used in the aerospace and military defense electrical interconnect systems.

Alternatives to Cadmium Plating

SAE AMS5854B-2010 自耗电极或真空感应融化61Ni 20.5Cr 8.5Mo 3.4Cb(Nb) 1.3Ti 5.0Fe镍合金耐腐蚀耐高温棒材,线材,锻件和环形材

This specification covers a corrosion and heat resistant nickel alloy in the form of bars, wire, forgings, flash welded rings, extrusions, and stock for forging or flash welded rings. These products have been used typically for parts requiring both corrosion and oxidation resistance up to 1000 °F (538 °C), and where such parts may require welding during fabrication and are then precipitation heat treated to develop required properties, but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Rings, 61Ni 20.5Cr 8.5Mo 3.4Cb(Nb) 1.3Ti 5.0Fe, Consumable Electrode or Vacuum Induction Melted Solution Heat Treated

SAE AMS5716J-2010 熔解热44Fe 18.5Cr 35.5Ni 1.1Si铁镍合金耐热棒材,线材,锻件和环形材

This specification covers a heat-resistant iron-alloy in the form of bars, wire, forgings, flash welded rings, and stock for forging or flash welded rings. These products have been used typically for low-stressed parts requiring oxidation up to 2100 °F (1149 °C), particularly where such parts may require welding during fabrication, but usage is not limited to such applications.

Iron-Nickel Alloy, Heat Resistant, Bars, Wire, Forgings, and Rings 44Fe - 18.5Cr - 35.5Ni - 1.1Si Solution Heat Treated

SAE AMS5786G-2010 62.5Ni 5.0Cr 24.5Mo 5.5Fe耐腐蚀和耐热镍合金焊条

This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire. Primarily for use as bare wire filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated from alloys of similar of dissimilar composition, but usage is not limited to such applications.

Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 62.5Ni 5.0Cr 24.5Mo 5.5Fe

SAE AMS5581F-2010 无缝或焊接管62Ni 21.5Cr 9.0Mo 3.7Cb (Nb)煅烧耐腐蚀耐热的镍合金

This specification covers a corrosion and heat resistant nickel alloy in the form of two types of tubing. This tubing has been used typically for fluid lines requiring high strength and corrosion resistance at temperatures from cryogenic to 1800 °F (982 °C), but usage is not limited to such applications.

Nickel Alloy, Corrosion And Heat Resistant, Seamless or Welded Tubing 62Ni 21.5Cr 9.0Mo 3.7Cb (Nb) Annealed

BS 3HR 1:2010 镍-铬-钛-铝耐热铝坯、棒、铸件和部件用规范(镍基,Cr 19.5, Ti 2.2,Al 1.4)

This British Standard specifies requirements for nickel-chromiumtitanium-aluminium heat‑resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: solution treated, designation HR 1A. b) Extruded sections for subsequent forming: softened, designation HR 1B. c) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 1C. d) Forgings: solution treated, designation HR 1D.

Specification for nickel-chromium-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 2.2, Al 1.4)

BS 3HR 1:2010+A1:2016 镍铬钛铝耐热合金坯料、棒材、锻件和零件规范（镍基、Cr 19.5、Ti 2.2、Al 1.4）

1   Scope This British Standard specifies requirements for nickel-chromium-titanium-aluminium heat-resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: solution treated, designation HR 1A. b) Extruded sections for subsequent forming: softened, designation HR 1B. c) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 1C. d) Forgings: solution treated, designation HR 1D.

Specification for nickel-chromium-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (Nickel base, Cr 19.5, Ti 2.2, Al 1.4)

BS 2HR 10:2010 镍-钴-铬-钼-钛-铝抗热合金坯料,棒材,锻件和零部件(镍基,Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5)规范

This British Standard specifies requirements for nickel-cobaltchromium- molybdenum-titanium-aluminium heat‑resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: solution treated, designation HR 10A. b) Extruded sections for subsequent forming: solution treated, designation HR 10B. c) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 10C. d) Forgings: solution treated, designation HR 10D.

Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5)

BS 2HR 4:2010 镍铬钴铝钼钛耐热合金坯、棒、铸件和部件用规范(镍基,Cr 15,Co 14. 2,Al 5,Mo 4,Ti 4)

This British Standard specifies requirements for nickel-chromiumcobalt-aluminium-molybdenum-titanium heat‑resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: solution treated, designation HR 4A. b) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 4B. c) Forgings: solution treated, designation HR 4C.

Specification for nickel-chromium-cobalt-aluminium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 15, Co 14. 2, Al 5, Mo 4, Ti 4)

BS 2HR 40:2010 钴-铬-钨-镍-锰耐热合金胚锭、棒材和锻件用规范(钴基Cr 20, W 15, Ni 10, Mn 1.5)

This British Standard specifies requirements for cobalt-chromiumtungsten-nickel-manganese heat‑resisting alloy supplied in the following forms. a) Bars and extruded sections for machining: annealed, designation HR 40A. b) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 40B. c) Forgings: annealed, designation HR 40C.

Specification for cobalt-chromium-tungsten-nickel-manganese heat-resisting alloy billets, bars and forgings (cobalt base Cr 20, W 15, Ni 10, Mn 1.5)

BS 2HR 5:2010 镍-铬-钛耐热铝坯、棒、铸件和部件用规范(镍基,Cr 19.5,Ti 0.4)

This British Standard specifies requirements for nickel-chromiumtitanium heat-resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: annealed, designation HR 5A. b) Extruded sections for subsequent forming: softened, designation HR 5B. c) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 5C. d) Forgings: annealed, designation HR 5D.

Specification for nickel-chromium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 0. 4)

BS 2HR 3:2010 镍-钴-铬-钼-铝-钛抗热合金坯料,棒材,锻件和零部件(镍基,Co 20, Cr 14. 8, Mo 5, Al 4.8, Ti 1.2)规范

This British Standard specifies requirements for nickel-cobaltchromium-molybdenum-aluminium-titanium heat-resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: solution treated, designation HR 3A. b) Extruded sections for subsequent forming: softened, designation HR 3B. c) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 3C. d) Forgings: solution treated, designation HR 3D.

Specification for nickel-cobalt-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 14. 8, Mo 5, Al 4.8, Ti 1.2)

BS 2HR 6:2010 镍-铬-铁-钼-钴-钨抗热合金坯料,棒材,锻件和零部件(镍基,Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6)规范

This British Standard specifies requirements for nickel‑chromiumiron‑molybdenum‑cobalt-tungsten heat‑resisting alloy supplied in the following forms, and as parts. a) Bars and extruded sections for machining: annealed, designation HR 6A. b) Billets and bars for forging: hot or cold worked and subsequently machined or ground, designation HR 6B. c) Forgings: annealed, designation HR 6C.

Specification for nickel-chromium- iron-molybdenum-cobalt-tungsten heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6)

BS 3HR 2:2010+A2:2012 镍-铬-钴-钛-铝的耐热合金坯锭,棒材,锻件和部件规格(镍基,Cr 19.5-Co 18.0-Ti 2.5-Al 1.5)

Specification for nickel-chromium-cobalt-titanium-aluminiumheat-resistin g alloy billets, bars, forgings and parts (Nickel base, Cr19.5, Co 18.0, Ti 2.5, Al 1.5)

BS 3HR 2:2010+A1:2011 镍-铬-钴-钛-铝的耐热合金坯料,棒材,锻件和部件规范(镍基合金,Cr 19.5,Co 18.0,Ti 2.5,Al 1.5)

Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (Nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5)

SAE AMS2630C-2010 超过0.5 inch(12.7 mm)厚产品超声波检验

This specification covers procedures for ultrasonic inspection, by pulse-echo procedure, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.50 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness. Parts with section thickness both over 0.50 inch (12.7 mm) and 0.5 inch (12.7 mm) and under may be tested using the procedure and AMS 2632, as applicable. This procedure has been used typically for locating and defining internal defects such as cracks, voids, laminations, and other structural discontinuities which may or may not be exposed to the surface, but usage is not limited to such applications.

Inspection, Ultrasonic Product Over 0.5 inch (12.7 mm) Thick

SAE AMS5585G-2010 32Fe 21Cr 20Ni 20Co 3Mo 2.5W 1.0Cb (Nb) 0.15N溶解热处理耐腐蚀和耐热合金焊接管形材料

This specification covers a corrosion and heat resistant iron alloy in the form of welded and drawn tubing. This tubing has been used typically for parts requiring high strength up to 1500 °F (816 °C) and oxidation resistance up to 1800 °F (982 °C), but usage is not limited to such applications.

Alloy, Corrosion and Heat Resistant, Welded Tubing 32Fe 21Cr 20Ni 20Co 3Mo 2.5W 1.0Cb (Nb) 0.15N Solution Heat Treated

SAE AMS5587F-2010 47.5Ni 22Cr 1.5Co 9.0Mo 0.60W 18.5Fe溶解热处理的耐腐蚀和耐热镍合金无缝管型材料

This specification covers a corrosion and heat resistant nickel alloy in the form of seamless tubing. This tubing has been used typically for fluid lines operating in service under appreciable stresses at elevated temperatures, but usage is not limited to such applications. Alloy has good strength up to 1800 °F (982 °C) and oxidation resistance up to 2200 °F (1204 °C).

Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 47.5Ni 22Cr 1.5Co 9.0Mo 0.60W 18.5Fe Solution Heat Treated