55.130 雾化剂罐 标准查询与下载

KS D ISO 10154-2019 轻型金属容器 三片缩口马口铁气雾罐 顶端尺寸

Light gauge metal containers－Three-piece necked-in tinplate aerosol cans－Dimensions of the top end

ASTM E2872-14(2019) 在风洞设备中使用激光衍射仪测定喷雾横截面平均特性的标准指南

1.1 The purpose of this guide is to define a test procedure for applying the laser diffraction (LD) method to estimate an average droplet size distribution that characterizes the flux of liquid droplets produced by a specified spray generation device under specified gas co-flow conditions using a specified liquid. The intended scope is limited to artificially generated sprays with high speed co-flow. The droplets are assumed to be in the size range of 1 to 2000 µm in diameter and occur in sprays that are contained within a volume as small as a few cubic centimetres or as large as a cubic metre. The droplet sizes are assumed to be distributed non-uniformly within the spray volume. 1.2 This guide is intended primarily to guide measurement of performance of nozzles and atomizers using LD instruments. 1.3 Non-uniform sprays require measurements across the entire spray cross section or through several chords providing a representative sample of the overall spray cross section. The aim of multiple-chord measurements is to obtain a single droplet size distribution that characterizes the whole spray rather than values from a single chordal measurement. 1.4 Use of this guide requires that the instrument does not interfere with spray production and does not significantly impinge upon or disturb the co-flow of gas and the spray. This technique is, therefore, considered non-intrusive. 1 This guide is under the jurisdiction of ASTM Committee E29 on Particle and Spray Characterization and is the direct responsibility of Subcommittee E29.02 on Non-Sieving Methods. Current edition approved Oct. 1, 2019. Published October 2019. Originally approved in 2014. Last previous edition approved in 2014 as E2872 – 14. DOI: 10.1520/E2872-14R19. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.5 The computation of droplet size distributions from the light-scattering distributions is done using Mie scattering theory or Fraunhofer diffraction approximation. The use of Mie theory accounts for light refracted through the droplet and there is a specific requirement for knowledge of both real (refractive) and imaginary (absorptive) components of the complex index of refraction. Mie theory also relies on an assumption of droplet homogeneity. The Fraunhofer diffraction approximation does not account for light refracted through the droplet and does not require knowledge of the index of refraction. 1.6 The instruments shall include data-processing capabilities to convert the LD scattering intensities into droplet size distribution parameters in accordance with Practice E799 and Test Method E1260. 1.7 The spray is visible and accessible to the collimated beam produced by the transmitter optics of the LD instrument. The shape and size of the spray shall be contained within the working distance of the LD system optics as specified by the instrument manufacturer. 1.8 The size range of the LD optic should be appropriate to the spray generation device under study. For example, the upper bound of the smallest droplet size class reported by the instrument shall be not more than 1⁄4 the size of DV0.1. 1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.10 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Determining Cross-Section Averaged Characteristics of a Spray Using Laser-Diffraction Instruments in a Wind Tunnel Apparatus

JIS S 3301:2018 气雾剂和气雾剂类产品的试验方法

Test methods of aerosol and aerosol-type products

ASTM D6535/D6535M-18 测定机械泵分配器浸渍管长度的标准实施规程

1.1 This practice covers the determination technique for a dip tube of a mechanical pump dispenser. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Dip Tube Length of a Mechanical Pump Dispenser

ASTM D6536/D6536M-18 测量机械泵分配器的浸渍管长度的标准实施规程

1.1 This practice covers the measurement technique for a dip tube of a mechanical pump dispenser. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Measuring the Dip Tube Length of a Mechanical Pump Dispenser

ASTM D3076-18 气雾剂容器外压接阀有效压接的标准实施规程

1.1 This practice covers the effective crimping on outside crimped valves within the wide parameters of containers and valves available. 1.2 Practices appear in the following order: Sections Optical Comparator Practice 4 to 7 Caliper Practice 8 to 12 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Effective Crimping on Outside Crimped Valves of Aerosol Containers

ASTM D4336-18 机械泵分配器每冲程输出量测定的标准实施规程

1.1 This practice covers the measurement of the mean quantity-by-weight of liquids dispensed from a mechanical pump dispenser (spray or flow type) with a consumer-type product on each actuation. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determination of the Output Per Stroke of a Mechanical Pump Dispenser

ASTM D3094-18 气溶胶产品渗透速率的标准实施规程

1.1 This practice covers the determination of approximate mass loss due to valve seepage rate2 of aerosol products by the collection and measurement of gases seeping through the valve and into a special eudiometer tube, over a relatively short time period. 1.2 It can be shown that the average refrigeration-filled aerosol product seeps to the extent of approximately 3.0 mL when the corresponding mass loss is 0.10 oz (2.9 cm3 )/year. This figure is partially based on air content and is subject to variations according to filling conditions. This practice is not considered dependable when applied to pressure-filled, unpurged aerosol products. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Seepage Rate of Aerosol Products

ASTM D3890-18 给机械泵分配器注水的冲程数的标准实施规程

1.1 This practice covers the determination of the number of actuations required to prime a pump dispenser (spray and flow types) with a consumer-type product. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Number of Strokes to Prime a Mechanical Pump Dispenser

ASTM D6534-18 测定机械泵分配器的最大驱动力的标准实施规程

1.1 This practice covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 5. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Peak Force-to-Actuate of a Mechanical Pump Dispenser

ASTM D3070-18 加压产品的快速压力测定的标准实施规程

1.1 This practice covers rapid pressure determination for pressurized products. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Rapid Pressure Determination of Pressurized Products

ASTM D4333/D4333M-18 机械泵分配器组件兼容性的标准实施规程

1.1 This practice covers testing of the components of mechanical pump dispensers (spray or flow types) for compatibility with products. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Compatibility of Mechanical Pump Dispenser Components

ASTM D6633-18 机械泵分配器基本功能稳定性的标准实施规程

1.1 This practice covers the determination of the basic functional stability of a mechanical pump dispenser with a product. 1.2 This practice covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) with a product. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific precautions are given in Section 5. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Basic Functional Stability of a Mechanical Pump Dispenser

ASTM D4041/D4041M-05(2017) 测定机械泵分配器喷雾模式的标准实施规程

1.1 This practice covers the determination of spray patterns from pump dispensers. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining Spray Patterns of Mechanical Pump Dispensers

BS EN 15007:2017 气雾剂容器 马口铁容器 二片罐和三片罐尺寸

Aerosol containers. Tinplate containers. Dimensions of two and three-piece cans

BS EN 15008:2017 气雾剂容器 铝制容器 孔径为 25.4 毫米的一体式罐头尺寸

Aerosol containers. Aluminium containers. Dimensions of one-piece cans with 25,4 mm aperture

DIN EN 15008:2017 雾化剂罐.铝罐.口径25.4mm的单层罐;德文版本EN 15008-2017

Aerosol containers - Aluminium containers - Dimensions of one-piece cans with 25,4 mm aperture; German version EN 15008:2017

DIN EN 15007:2017 气溶胶容器.马口铁容器.两件或三件套容器尺寸;德文版本EN 15007-2017

Aerosol containers - Tinplate containers - Dimensions of two and three-piece cans; German version EN 15007:2017

NF H44-044*NF EN 15007:2017 雾化剂罐.马口铁罐.三层罐开口尺寸

Aerosol containers - Tinplate containers - Dimensions of two and three-piece cans

EN 15007:2017 雾化剂容器-马口铁容器-两件或三件套容器尺寸

This European Standard specifies the dimensions of two and three-piece tinplate aerosol containers with nominal brimful capacities.

Aerosol containers - Tinplate containers - Dimensions of two and three-piece cans