55.180.01 货物调运综合 标准查询与下载

NF H00-072-3*NF EN 15433-3:2008 运输荷载.动力机械荷载的测量和评定.第3部分:评定用数据有效性检验和数据编辑

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3 : data validity check and data editing for evaluation.

NF H00-072-6:2008 运输载荷.动态机械载荷的测量和评定.第6部分:运输监控中偶然出现振动的测量用自动记录系统

Transportation loads - Measurement and evaluation of dynamic-mechanical loads - Part 6 : automatic recording systems for measuring randomly occuring shock during monitoring of transports.

DIN EN 15433-1:2008 运输载荷.动力机械载荷的测量和评价.第1部分:一般要求

This standard specifies the general requirements to be observed during the measurement and evaluation of dynamic-mechanical transportation loads, should the results raise a claim of generalization and be incorporated in this series of standards as fundamental data.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 1: General requirements; English version of DIN EN 15433-1:2008-02

DIN EN 15433-3:2008 运输载荷.动力机械载荷的测量和评价.第3部分:评价数据的有效性检查和编辑

This standard defines procedures for assessing the validity of results acquired in accordance with EN 15433-2, and for evaluating these results. NOTE When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognize disturbances or erroneous measurements occur, which impair the application of these values. These procedures are necessary in order to detect possible errors before any actual analysis occurs. Figure 1 provides an overview of the data validation and editing processes in this standard.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3: Data validity check and data editing for evaluation; English version of DIN EN 15433-3:2008-02

DIN EN 15433-5:2008 运输载荷.动力机械载荷的测量和评价.第5部分:试验规范的推导

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4. NOTE To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particular has to be considered for the determination of the test intensity.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 5: Derivation of test specifications; English version of DIN EN 15433-5:2008-02

DIN EN 15433-4:2008 运输量.动力机械载荷的测量和评估.第4部分:数据评估

This standard presents guidelines for the instruments, procedures and parameters, used to analyse dynamic data. It is assumed that the person performing the analyses has the use of appropriate digital FFT signal processors or FFT computers. These guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent. Such other procedures contain correlation algorithms e.g. Blackman-Tuckey), digital band pass filter algorithms or heterodyne techniques. An outline of the data analysis procedures covered in this section is presented in Figure 1.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 4: Data evaluation; English version of DIN EN 15433-4:2008-02

DIN EN 15433-2:2008 运输量.动力机械荷载的测量和评估.第2部分:测量设备的数据采集和一般要求

This standard specifies requirements for the preparation, performance and documentation of transportation measurements.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 2: Data acquisition and general requirements for measuring equipment; English version of DIN EN 15433-2:2008-02

DIN EN 15433-6:2008 运输量.动力机械荷载的测量和评估.第6部分:运输监控中偶然出现的振动测量用自动记录系统

This standard specifies the technical and functional properties of automatic recording equipment used to determine randomly appearing shocks during transportation. Such automatic recording equipment can be used to: -- determine mechanical shock loads on individual transportations; -- monitor the transportation means to observe the limits of the shock parameters; -- determine the shock loads on the transported item. This standard defines the sensors to be attached to the device, and specifies the minimum requirements for the parameters to be adjusted. It also defines the minimum requirements for the data analysis, as well as the data presentation. This standard covers the complete recording equipment, including its accelerometers and the data analysis in an external data processing unit. The accelerometers can be integrated into the device or separately mounted from it (external sensors). This standard also applies to the routine monitoring of individual transportations

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 6: Automatic recording systems for measuring randomly occurring shock during monitoring of transports; English version of DIN EN 15433-6:2008-02

BS EN 15433-3:2008 运输载荷 动力机械荷载的测量和评估 第3部分：评估用数据有效性检验和数据编辑

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Data validity check and data editing for evaluation

BS EN 15433-5:2008 运输载荷 动力机械载荷的测量和评估 第5部分：试验规范的推导

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Derivation of test specifications

BS EN 15433-4:2008 运输载荷 动力机械载荷的测量和评估 第4部分：数据评估

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Data evaluation

BS EN 15433-6:2008 运输载荷 动力机械荷载的测量和评估 第6部分：运输监测期间随机出现的振动测量用自动记录系统

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Automatic recording systems for measuring randomly occurring shock during monitoring of transports

BS EN 15433-6:2007 运输载荷.动力机械荷载的测量和评估.第6部分:运输监测期间随机出现的振动测量用自动记录系统

This standard specifies the technical and functional properties of automatic recording equipment used to determine randomly appearing shocks during transportation. Such automatic recording equipment can be used to:  determine mechanical shock loads on individual transportations;  monitor the transportation means to observe the limits of the shock parameters;  determine the shock loads on the transported item. This standard defines the sensors to be attached to the device, and specifies the minimum requirements for the parameters to be adjusted. It also defines the minimum requirements for the data analysis, as well as the data presentation. This standard covers the complete recording equipment, including its accelerometers and the data analysis in an external data processing unit. The accelerometers can be integrated into the device or separately mounted from it (external sensors). This standard also applies to the routine monitoring of individual transportations

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 6: Automatic recording systems for measuring randomly occurring shock during monitoring of transports

BS EN 15433-5:2007 运输载荷.动力机械载荷的测量和评估.第5部分:试验规范的推导

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4. NOTE To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particular has to be considered for the determination of the test intensity.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 5: Derivation of Test Specifications

BS EN 15433-4:2007 运输载荷.动力机械载荷的测量和评估.第4部分:数据评估

This standard presents guidelines for the instruments, procedures and parameters, used to analyse dynamic data. It is assumed that the person performing the analyses has the use of appropriate digital FFT signal processors or FFT computers. These guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent. Such other procedures contain correlation algorithms e.g. Blackman-Tuckey), digital band pass filter algorithms or heterodyne techniques.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 4: Data evaluation

BS EN 15433-3:2007 运输载荷.动力机械荷载的测量和评估.第3部分:评估用数据有效性检验和数据编辑

This standard defines procedures for assessing the validity of results acquired in accordance with EN 15433-2, and for evaluating these results. NOTE When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognize disturbances or erroneous measurements occur, which impair the application of these values. These procedures are necessary in order to detect possible errors before any actual analysis occurs.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3: Data validity check and data editing for evaluation

BS EN 15433-1:2007 运输载荷.动力机械载荷的测量和评估.第1部分:一般要求

BS EN 15433-1:2007 specifies the general requirements to be observed during the measurement and evaluation of dynamic-mechanical transportation loads, should the results raise a claim of generalization and be incorporated in this series of standards as fundamental data. It is part of a complete normative concept to acquire and describe the loads acting on goods and influencing them during transport, handling and storage.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 1: General requirements

EN 15433-1:2007 运输载荷.动力机械载荷的测量和评价.第1部分:一般要求

This standard specifies the general requirements to be observed duringThe measurement and evaluation of dynamic-mechanical transportation loads, shouldThe results raise a claim of generalization and be incorporated inThis series of standards as fundamental data.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 1: General requirements

EN 15433-4:2007 运输载荷.动力机械载荷的测量和评定.第4部分:数据的评价

This standard presents guidelines for the instruments, procedures and parameters, used to analyse dynamic data. It is assumed that the person performing the analyses has the use of appropriate digital FFT signal processors or FFT computers. These guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent. Such other procedures contain correlation algorithms e. g. Blackman-Tuckey), digital band pass filter algorithms or heterodyne techniques. An outline of the data analysis procedures covered inThis section is presented in Figure 1. Figure 1-Outline of data analysis

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 4: Data evaluation

EN 15433-2:2007 运输载荷.动力机械荷载的测量和评定.第2部分:测量设备的数据采集和一般要求

This standard specifies requirements forThe preparation, performance and documentation of transportation measurements.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 2: Data acquisition and general requirements for measuring equipment