59.140.40 皮革和毛皮加工机械和设备 标准查询与下载

DIN EN 1035:1999 制革机.移动熨平机械.安全性要求

The document defines safety requirements for construction, transport, installation, adjustment, setting, teaching or process change over, operation, cleaning, maintenance etc. for moving plate machines.

Tannery machines - Moving plate machinery - Safety requirements; German version EN 1035:1998

DS/EN 1035:1999 制革机 移动压板机械 安全要求

This European Standard specifies safety requirements for all the phases of the life of a machine listed in 3.11.a of EN 292-1:1991. Moving platen machines are machines used for the processing of animal hides and skins. They are table type processing machines which are equipped with vertical opening and closing movement and alternative horizontal feed-in and feed-out movement.

Tannery machines - Moving platen machinery - Safety requirements

BS EN 1035:1999 鞣皮机.移动台板机.安全性要求

This European Standard specifies safety requirements for all the phases of the life of a machine listed in 3.11.a of EN 292-1:1991. Moving platen machines are machines used for the processing of animal hides and skins. They are table type processing machines which are equipped with: —vertical opening and closing movement; —alternative horizontal feed-in and feed-out movement. This European Standard covers the following machines (see Figures 1 to 5 for typical configurations and normative annex C for descriptions): a) vacuum dryers with vertical movement (see Figure 1); b) vacuum dryers with horizontal and vertical movement (see Figure 2); c) vacuum stretching-machines (see Figure 3); d) platen ironing and embossing machines with vertical movement (see Figure 4); e) platen ironing and embossing machines with horizontal and vertical movement (see Figure 5). It takes account of intended use, foreseeable misuse, component and systems failure. This European Standard applies to the machines manufactured after its date of issue. All the significant hazards listed in clause 4 are covered by the requirements included in clause 5 except: —dust, fume, vapour and liquid emissions, for which general guidelines are proposed in the informative annex B. Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.

Tannery machines. Moving platen machinery. Safety requirements

SNI 05-6079-1999 液压机性能测试方法

Performance test method for glue system shoes' sole hydraulic press machines

SNI 05-4986-1999 切割机性能的检测

Performance test method of skiving machines

NF G54-101:1998 制革机械.往复式滚压成形机.安全要求

Tannery machines. Reciprocating roller machines. Safety requirements.

EN 1035:1998 鞣皮机.移动平整机.安全要求.合并勘误表-2002年7月

Tannery Machines - Moving Platen Machinery - Safety Requirements (Incorporating Corrigendum July 2002)

BS EN 972:1998 制革机械.往复滚压机的安全性要求

This European Standard specifies safety requirements for all the phases of the life of a machine listed in 3.11a) of EN 292-1:1991. Reciprocating roller machines are machines used for the processing of animal hides and skins. They have a reciprocating opening and closing motion of the feed rollers or conveyors which, if required, may also reverse their direction. This standard covers the following reciprocating roller machines (see Figures 1 to 13 for typical configurations and annex D for descriptions): a) buffing machines [see Figures la) and lb)]; b) polishing machines [see Figures la) and lb)]; c) ironing machines (woolskins and fur) [see Figures 2a) and 2b)]; d) carding machines [see Figures 3a) and 3b)]; e) shearing machines (woolskins and fur) [see Figures 4a) and 4b)]; f) cylinder universal staking machines [see Figures 5a) and 5b)]; g) setting-out machines [see Figures 6a) and 6b)]; h) dewooling machines [see Figures 6a) and 6b)]; i) scudding machines [see Figures 6a) and 6b)]; j) unhairing (dehairing) machines [see Figures 6a) and 6b)]; k) sammying machines [see Figures 6a) and 6b)]; 1) cylinder ironing machines [see Figures 7a) and 7b)]; m) cylinder staking machines [see Figures 8a) and 8b)]; n) fleshing machines [see Figures 9a) and 9b)]; o) demanuring machines [see Figures 10a) and 10b); p) wet wheeling machines [see Figures lla) and l1b)]; q) shaving machines (feed-out) [see Figures 12a) and 12b)]; r) shaving machines (feed-in) [see Figures 13a) and 13b). It takes account of intended use, foreseeable misuse, component and systems failure. This European Standard applies to machines manufactured after its date of issue. All the significant hazards listed in clause 4 are safeguarded by the requirements included in clause 5 except the following: —dust, smoke and vapour emissions (see annex B); —fire (see annex C). For these hazards general guidelines are proposed in informative annexes. Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.

Tannery machines - Reciprocating roller machines - Safety requirements

BS EN 972:1998+A1:2010 制革机械.往复滚压机.安全性要求

This European Standard specifies safety requirements for all the phases of the life of a machine listed in !5.3 a) of EN ISO 12100-1:2003". Reciprocating roller machines are machines used for the processing of animal hides and skins. They have a reciprocating opening and closing motion of the feed rollers or conveyors which, if required, may also reverse their direction. This standard covers the following reciprocating roller machines (see figures 1 to 13 for typical configurations and annex D for descriptions): a) Buffing machines (see figures 1a and 1b) b) Polishing machines (see figures 1a and 1b) c) Ironing machines (woolskins and fur) (see figures 2a and 2b) d) Carding machines (see figures 3a and 3b) e) Shearing machines (woolskins and fur) (see figures 4a and 4b) f) Cylinder universal staking machines (see figures 5a and 5b) g) Setting-out machines (see figures 6a and 6b) h) Dewooling machines (see figures 6a and 6b) i) Scudding machines (see figures 6a and 6b) j) Unhairing (dehairing) machines (see figures 6a and 6b) k) Sammying machines (see figures 6a and 6b) l) Cylinder ironing machines (see figures 7a and 7b) m) Cylinder staking machines (see figures 8a and 8b) n) Fleshing machines (see figures 9a and 9b) o) Demanuring machines (see figures 10a and 10b) p) Wet wheeling machines (see figures 11a and 11b) q) Shaving machines (feed-out) (see figures 12a and 12b) r) Shaving machines (feed-in) (see figures 13a and 13b) It takes account of intended use, foreseeable misuse, component and systems failure. !This European Standard is not applicable to reciprocating roller machines which are manufactured before the date of its publication as EN." !This European Standard provides provisions for the reduction of noise emission at the design stage (see 5.2.4 and Annex A). However, it does not provide a noise test code for the determination by measurement of noise emission values for the machines it covers. Without such a code the manufacturer cannot fulfil his obligation to provide the noise emission values of the machines put on the market." !All the significant hazards (see Clause 4) are dealt with in this European Standard except the following:" ? Dust, smoke and vapour emissions (see Annex B); ? Fire (see Annex C). For these hazards general guidelines are proposed in !normative annexes". Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.

Tannery machines. Reciprocating roller machines. Safety requirements

EN 972:1998 制革机械.往复滚柱机械.安全要求

This European Standard specifies safety requirements for all the phases of the life of a machine listed in 5.3 a) of EN ISO 12100-1:2003. Reciprocating roller machines are machines used for the processing of animal hides and skins. They have a reciprocating opening and closing motion of the feed rollers or conveyors which, if required, may also reverse their direction.This standard covers the following reciprocating roller machines (see figures 1 to 13 for typical configurations and annex D for descriptions): a) Buffing machines (see figures 1a and 1b) b) Polishing machines (see figures 1a and 1b) c) Ironing machines (woolskins and fur) (see figures 2a and 2b) d) Carding machines (see figures 3a and 3b) e) Shearing machines (woolskins and fur) (see figures 4a and 4b) f) Cylinder universal staking machines (see figures 5a and 5b) g) Setting-out machines (see figures 6a and 6b) h) Dewooling machines (see figures 6a and 6b) i) Scudding machines (see figures 6a and 6b) j) Unhairing (dehairing) machines (see figures 6a and 6b) k) Sammying machines (see figures 6a and 6b) l) Cylinder ironing machines (see figures 7a and 7b) m) Cylinder staking machines (see figures 8a and 8b) n) Fleshing machines (see figures 9a and 9b) o) Demanuring machines (see figures 10a and 10b) p) Wet wheeling machines (see figures 11a and 11b) q) Shaving machines (feed-out) (see figures 12a and 12b) r) Shaving machines (feed-in) (see figures 13a and 13b) It takes account of intended use, foreseeable misuse, component and systems failure.This European Standard is not applicable to reciprocating roller machines which are manufactured before the date of its publication as EN.This European Standard provides provisions for the reduction of noise emission at the design stage (see 5.2.4 and Annex A). However, it does not provide a noise test code for the determination by measurement of noise emission values for the machines it covers. Without such a code the manufacturer cannot fulfil his obligation to provide the noise emission values of the machines put on the market. All the significant hazards (see Clause 4) are dealt with inThis European Standard except the following: Dust, smoke and vapour emissions (see Annex B); Fire (see Annex C). For these hazards general guidelines are proposed in normative annexes. Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.

Tannery machines - Reciprocating roller machines - Safety requirements (Incorporates Amendment A1: 2010; Incorporating corrigendum April 2011)

SNI 05-4556-1998 皮革分机裂性能测试

Performance test of leather splitting machine

EN 931:1997 鞋制造机械.拉伸机械.安全要求;包含修改件A2-2009

This standard is applicable to lasting machines used in the footwear manufacturing industry; namely: Adhesive fore part lasting machines (see figure 1); Hand operated adhesive side lasting machines (see figure 3 A); Adhesive seat lasting machines (see figure 2); Adhesive seat and side lasting machines (see figure 2); Hand operated tack/staple side lasting machines (see figure 3B); Tack seat lasting machines (see figure 2); Tack seat and side thermocement lasting machines (see figure 2); Tack heel seat and thermocent side lasting machines (see figure 2); Tack heel seat and thermocent + tack side lasting machines (see figure 2).This standard does not apply to lasting machines which process granular thermocement.This standard specifies requirements for safe design; construction and use of the machines. No specific requirements are included for transport; commissioning and decommissioning. It takes account of intended use; foreseeable misuse; component and system failure.This standard covers all hazards relevant to the footwear manufacturing industry. The use of machines within the scope of this standard in different industries may give rise to hazards which were not taken into account at the time of its preparation.This document is not applicable to lasting machines which are manufactured before the date of its publication as EN.

Footwear manufacturing machines - Lasting machines - Safety requirements (Incorporates Amendment A2: 2009)

SNI 06-1846-1990 制革机橡胶滚轴. 硬度

Rubber roll hardness for tanning leather machine

GOST 27444-1987 皮革压延机.基本参数及尺寸，技术要求

Leather rolling machines, types, main parametres and dimensions, technical requirements

GOST 27443-1987 制革皮里清除机.基本参数及尺寸，技术要求

Zeather fleshing machines. Main parameters, dimensions and requirements

NF G83-001:1970 鞋袜制造机械.削皮机用圆形刀

Machinery for the manufacture of footwear. Circular knife for hide paring machines.