73.060.01 金属矿综合 标准查询与下载

GB/T 2468.3-1996 硫铁矿和硫精矿中锌含量的测定 第3部分;PAN 分光光度法

本标准规定了分光光度法测定锌含量。 本标准适用于硫铁矿和硫精矿产品中锌含量0.01%～0.3%的测定。

Pyrites and concentrate--Determination of zinc content--Part 3: PAN spectrophotometric method

GB/T 16574-1996 硫铁矿和硫精矿中硅含量的测定 重量法

本标准规定了高氯酸脱水重量法测定二氧化硅含量。 本标准适用于硫铁矿和硫精矿产品中二氧化硅含量大于1%的测定。

Pyrites and concentrate--Determination of silicon content--Gravimetric method

GB/T 16575-1996 硫铁矿和硫精矿中铝含量的测定 EDTA容量法

本标准规定了EDTA容量法测定氧化铝含量。 本标准适用于硫铁矿和硫精矿产品中氧化铝含量大于0.2%的测定。

Pyrites and concentrate--Determination of aluminium content--EDTA volumetric method

GB/T 2460-1996 硫铁矿和硫精矿 采样与样品制备方法

本标准规定了硫铁矿和硫精矿矿石产品采样与样品制备方法。

Pyrites and concentrate--Methods for sampling and preparation sample

GB/T 2462-1996 硫铁矿和硫精矿中有效硫含量的测定 燃烧中和法

本标准规定了燃烧中和法测定有效硫含量。 本标准适用于硫铁矿和硫精矿产品中有效硫含量大于10%的测定。

Pyrites and concentrate--Determination of effective sulfur content--Combustion neutralization method

T/CI 183-2023 非煤矿山智慧化建设规程

本文规定了非煤矿山智慧建设的方向、建设模块、模块指标、非煤矿山智慧化建设等级程度的技术要求。 本文适用于各类非煤矿山：金属矿山、非金属矿物矿山（煤炭除外）等矿山智慧化建设与评价。

Non-coal mine intelligent construction regulations

T/CIQA 66-2023 矿石中水分的快速测定 远红外干燥法

探讨不同加热温度、样品重量、干燥时间等试验条件对远红外干燥法快速测定矿石中水分分析的影响，确定测定矿石中水分远红外干燥法的最佳条件。

Rapid determination of water content in ores-Far infrared drying method

T/MMAC 012-2023 金属矿深竖井建设工程勘察技术规范

本文件规定了金属矿深竖井建设所需的术语和定义、符号和缩略语、一般规定、工程资料收集与分析、勘察手段和方法、工程地质、水文地质、环境地质、岩石力学、成果编制等要求。 本文件适用于金属矿1000m及以深竖井建设工程勘察的相关技术工作。

Technical specification for investigation of deep shaft construction engineering in metal mine

T/CGA 40-2023 尾矿库无人机遥感巡查 通用要求

1  范围 2  规范性引用文件 3  术语和定义 4  目的与任务   4.1  目的   4.2  任务 5  航摄系统要求   5.1  飞行准备   5.2  无人机平台要求   5.3  搭载传感器要求   5.4  通信性能要求 6  航摄计划与航摄设计   6.1  航摄计划   6.2  航摄设计   6.3  安全作业要求 7  航摄质量与数据后处理   7.1  飞行拍摄质量   7.2  影像质量   7.3  数据后处理   7.4  成果质量检查 8  信息提取   8.1  库容、坝高变化   8.2  干滩长度   8.3  平均坡度   8.4  日常巡查   8.5  库区地形 9  档案管理 附录A（规范性）  飞行记录表

Tailings ponds inspection by unmanned aerial vehicle（UAV） remote sensing—General requirements

T/CI 057-2023 金属矿山地质灾害预警信息系统建设技术规程

4　总则 在金属矿山开采过程中，因为爆破、采掘等工程活动，导致原有的地质条件发生变化，极易诱发地质灾害。对生态环境、自然资源和社会经济造成不可估量的危害和破坏。金属矿山的信息化建设是当前的发展趋势，但目前对信息系统的建设缺乏明确的规定和标准，致使很多矿山存在多个信息化系统，且系统间未实现联通，管理难度大。因此，针对矿山信息化建设现状，亟需从金属矿山信息系统建设、金属矿山监测对象、监测系统、人工巡查、数据管理与分析、预警和运行维护几个方面，制定一套金属矿山地质灾害监测预警信息系统建设技术规程，指导和规范金属矿山行业信息化建设工作。 5　基本规定 预警信息系统建设应按设计要求执行。 预警信息系统应具备对各功能模块的管理功能。 预警信息系统监控中心设备应具有可靠的防雷和接地保护装置。 主机应安装在地面，并可定期自动化备份，且应在矿山调度中心设置显示终端。 应配备监测站、传感器等监测监控设备备件，备用数量应满足定期巡检运维需要。 预警信息系统可长期、稳定运行。 预警信息系统应具有矿用产品安全标志。 预警信息系统部署完毕或维护和升级之后，应按使用说明书要求测试、调校，经测试合格后方可使用。

Technical regulations for the construction of geological disaster early warning information system for metal mines

T/CACE 061-2022 铜冶炼用工业废渣制烧结料

1 范围　 2 规范性引用文件　 3 术语和定义 4 技术要求　 5 试验方法　 6 检验规则　 7 包装、标志、运输和贮存　

Sintering material from the industrial waste slags for copper smelting

T/MMAC 005-2022 金属矿山全尾砂胶结充填胶凝材料

本文件规定了金属矿山全尾砂胶结充填胶凝材料的术语和定义、分类和标记、组分与材料、强度等级、技术要求、试验方法、检验规则和包装、标志、运输与贮存要求。 本文件适用于金属矿山全尾砂胶结充填胶凝材料的生产、贮存、运输和管理。

Cementing materials for full tailing concreted backfilling of metal mine

T/MMAC 006-2022 金属矿山尾矿充填检测方法

本文件规定了金属矿山尾矿充填料浆及充填体坍落度与坍落扩展、凝结时间、泌水与压力泌水、抗压强度、干缩率性能检测方法的仪器、材料、试验条件、操作步骤和结果计算等。 本文件适用于以金属矿山尾矿为骨料、选矿废水为拌合水、胶凝材料为胶结剂的充填料浆和充填体的各项性能指标的检测。

Detection method of tailings filling in metal mines

JIS M 8132:2021 矿石 砷的测定方法

Ores -- Methods for determination of arsenic

ASTM E2295-21 通过熔渣和杯中银的测定分析含金属矿石、精矿和相关冶金材料时火试金银校正的标准实施规程

1.1 This practice covers the determination of silver corrections for fire assay of metal bearing ores, concentrates, and related metallurgical materials using the spent slags and cupels from the fire assay process, by gravimetry and atomic absorption spectrophotometry. 1.2 The test methods appear in the following order: Sections Gravimetric Method 10–11 Atomic Absorption Method 12–13 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (See Practices E50 and ISO Guide 35:1989.) 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Fire Assay Silver Corrections in Analysis of Metal Bearing Ores, Concentrates, and Related Metallurgical Materials by Silver Determination in Slags and Cupels

ASTM E2242-21 用大气水迁移率法对矿山岩石进行柱渗滤提取的标准试验方法

1.1 This test method provides a procedure for the column percolation extraction of mine rock in order to determine the potential for dissolution and mobility of certain constituents by meteoric water. 1.2 This test method is intended to describe the procedure for performing column percolation extractions only. It does not describe all types of sampling and analytical requirements that may be associated with its application. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Column Percolation Extraction of Mine Rock by the Meteoric Water Mobility Procedure

ASTM E2294-21 用火试金重量分析法检验含金属矿石、精矿和相关材料中银校正的标准实施规程

1.1 This practice covers the determination of fire assay correction for silver, utilizing proof silver, ores, concentrates, and related metallurgical materials. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (See Test Methods E1335, Practices E50, Guide E882, and ISO Guide 35: 2017.) 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Proof Silver Corrections in Metal Bearing Ores, Concentrates, and Related Materials by Fire Assay Gravimetry

ASTM E2941-21 用酸消化法从矿石和相关冶金材料中提取元素的标准实施规程

1.1 These practices cover the digestion of ores and related metallurgical materials, such as mine soil, waste rock and tailings, for subsequent determination of acid-extractable contents of certain elements by such solution analytical techniques as atomic absorption spectrometry (AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) (see Test Method D1976), and inductively coupled plasma mass spectrometry (ICP-MS) (see Test Method D5673). 1.1.1 Contents of aluminum, antimony, arsenic, barium, beryllium, bismuth, boron, cadmium, calcium, chromium, cobalt, copper, gallium, iron, lead, lithium, magnesium, manganese, mercury, molybdenum, nickel, phosphorus, potassium, scandium, selenium, silver, sodium, strontium, thallium, tin, titanium, vanadium and zinc can be extracted from ores and related metallurgical materials for determination by analytical methods for elements in solution. Other elements may be determined from extracts produced using this practice. 1.1.2 Actual element quantification in digested solutions can be accomplished by following the various test methods under other appropriate ASTM standards for element(s) of interest in solution. 1.1.3 The detection limit and linear content range for each element is dependent on the atomic absorption, mass spectrometry or emission spectrometric technique employed and may be found in the manual accompanying the instrument used or ASTM standard method for analysis of the solutions. Consider the dilution factor in content calculations due to digestion and dilution of solid samples. 1.1.4 The extent of extraction of elements from ores and related metallurgical materials by these practices is dependent upon the physical and mineralogical characteristics of the prepared sample and the digestion practice used. 1.2 The digestion practices appear in the following order: Sections Nitric Acid Microwave Digestion 7 to 14 Four-Acid Total Digestion 15 to 21 1.3 The values stated SI units are to be regarded as the standard. No other units of measurements are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 11 and 20. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practices for Extraction of Elements from Ores and Related Metallurgical Materials by Acid Digestion

KS E 3001-2021 矿石中铜的测定方法

Methods for determination of copper in ores

YS/T 3040-2021 金矿全尾砂充填环管测定技术规范

Technical Specifications for Determination of Full Tailings Filling Ring Pipes in Gold Mines