77.040.99 金属材料的其他试验方法 标准查询与下载

T/CSTM 00244-2021 金属材料 物理模拟试验方法 第1部分：轴对称热压缩试验

本文件规定了金属材料轴对称热压缩试验的术语和定义、符号、试样、试验系统、试验条件和步骤、试验结果处理和试验报告。 本文件适用于试验温度高于室温条件，应变速率在10-4/ s～102/ s之间金属材料高温流变应力的测定。

Metallic materials – Method of physical simulation tests – Part 1： Hot axisymmetric compression testing

DS/ISO 18203:2021 钢 表面硬化层厚度的测定

Steel – Determination of the thickness of surface-hardened layers

T/GDES 62-2021 铝型材企业水平衡测试操作规范

本文件规定了铝型材企业水平衡测试的方法、程序、结果评估和报告格式。  本文件适用于铝型材企业开展水平衡测试。其他铝材加工企业可参考执行。

Operation specification for water balance test of aluminum profile enterprises

ASTM E96/E96M-21 重量法测定材料水蒸气透过率的标准试验方法

Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials

T/CMA YJ069-0201 钢筋弯曲试验机计量技术要求

钢筋弯曲试验机是对钢筋进行冷弯试验和平面反向弯曲试验的专用设备。目前尚无国家计量检定规程/校准规范，该设备技术参数和指标符合YB/T 5126-2003 钢筋混凝土用钢筋弯曲和反向弯曲试验方法》、GB1499.2-2007《钢筋混凝土用钢管第2部分：热轧带肋钢筋》；该产品广泛应用于冶金、机械制造业、建筑施工业、工程监理、技术质量监督等单位，以检验各种钢筋正向、反向弯曲的机械性能。由于缺少相应的校准依据，无法合理判断该设备的计量性能和弯曲结果是否满足要求。因此，本规范的制定，能有效判定在用钢筋弯曲试验机的工作性能是否符合工作要求。标准内容包含：测量原理与一般要求、计量特性实现、计量结果表达、计量时间间隔、钢筋弯曲试验机计量记录参考格式（附录A）、钢筋弯曲试验机弯曲角度测量不确定度评定（附录B）等。

Technical Requirements for Measurement of Steel Bar Bending Testing Machine

GSO ISO 4499-4:2021 硬质合金 显微组织的金相测定 第4部分：孔隙率、碳缺陷和 eta 相含量的表征

ISO 4499-4:2016 specifies methods for the metallographic determination of the presence, type, and distribution of porosity, uncombined carbon and eta-phase in hardmetals.

Hardmetals — Metallographic determination of microstructure — Part 4: Characterisation of porosity, carbon defects and eta-phase content

GSO ISO 4499-3:2021 硬质合金 微观结构的金相测定 第3部分：Ti（C N）和 WC/立方碳化物基硬质合金微观结构特征的测量

ISO 4499-3:2016 gives guidelines for the measurement of microstructural features in Ti(C,N) based hardmetals and WC/Co hardmetals that contain additional cubic carbides by metallographic techniques only using optical or electron microscopy. It is intended for sintered hardmetals (also called cemented carbides or cermets) containing primarily inorganic carbides and nitrides as the hard phase. It is also intended for measuring the phase size and distribution by the linear intercept technique.

Hardmetals — Metallographic determination of microstructure — Part 3: Measurement of microstructural features in Ti (C, N) and WC/cubic carbide based hardmetals

GSO ISO 16574:2021 高碳钢盘条中可溶解珠光体百分率的测定

ISO 16574:2015 defines resolvable pearlite and specifies two methods of determining the percentage of resolvable pearlite. The methods are applicable for wire rod made from control cooling steel with carbon content greater than 0,65 % C.

Determination of percentage of resolvable pearlite in high carbon steel wire rod

T/CNIA 0107.1-2021 铜及铜合金显微组织及断口图谱 第1部分：高铜系列

本文件给出了高铜合金在铸造、轧制、挤压、固溶等不同状态下的显微组织及断口图谱。 本文件适用于高铜合金在不同工艺过程阶段加工制品的组织检验和判定。

Microstructure and Fracture Diagram of Copper and Copper Alloy Part 1: High Copper Series

T/FJMA 001-2021 热轧带肋钢筋金相组织检验及判定标准

规定了钢筋混凝土用热轧带肋钢筋产品金相组织（宏观金相、微观组织、晶粒度、低倍组织及缺陷）检验采用的标准和方法，并给出了宏观金相、微观组织项目的判定准则。

Inspection and judgment standard for metallographic structure of hot-rolled ribbed steel bar

ASTM G129-21 用于缓慢应变速率测试以评估金属材料对环境辅助开裂的敏感性的标准实践

1.1?This practice covers procedures for the design, preparation, and use of axially loaded, tension test specimens and fatigue pre-cracked (fracture mechanics) specimens for use in slow strain rate (SSR) tests to investigate the resistance of metallic materials to environmentall

Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking

JIS G 0561:2020 钢的淬透性试验方法(顶淬火法)

Method of hardenability test for steel (End quenching method)

JIS G 0558:2020 钢. 脱碳深度测定

Steels -- Determination of depth of decarburization

T/ZSA 17-2020 抗菌不锈钢表面抗菌性能 试验方法

抗菌不锈钢作为新型的结构功能一体化材料已被广泛应用于各个领域。为快速真实有效检测出抗菌不锈钢的抗菌性能，特制定本文件。本文件主要基于抗菌材料对细菌的接触杀菌机制，提供抗菌不锈钢抗菌效果的评价方法。对于抗菌不锈钢的其他重要性能，如产品的理化性能和安全性可参考其他相关标准，在本文件中不作规定。

Antibacterial stainless steel—Measurement of antibacterial property

YB/T 5360-2020 金属材料 定量极图的测定 X射线衍射法

Determination of quantitative pole figures of metallic materials by X-ray diffraction method

YS/T 347-2020 铜及铜合金平均晶粒度测定方法

Method for determination of average grain size of copper and copper alloys

ASTM E1351-01(2020) 现场金相复制品的生产和评估标准实践

1.1 This practice covers recognized methods for the preparation and evaluation of cellulose acetate or plastic film replicas which have been obtained from metallographically prepared surfaces. It is designed for the evaluation of replicas to ensure that all significant features of a metallographically prepared surface have been duplicated and preserved on the replica with sufficient detail to permit both LM and SEM examination with optimum resolution and sensitivity. 1.2 This practice may be used as a controlling document in commercial situations. 1.3 The values stated in SI units are to be regarded as the standard. Inch-pound units given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Production and Evaluation of Field Metallographic Replicas

OENORM EN ISO 4499-1:2020 硬质合金 微观结构的金相测定 第1部分：显微照片和描述（ISO 4499-1:2020）

Hardmetals - Metallographic determination of microstructure - Part 1: Photomicrographs and description (ISO 4499-1:2020)

OENORM EN ISO 4499-2:2020 硬质合金 微观结构的金相测定 第2部分：WC 晶粒尺寸的测量（ISO 4499-2:2020）

Hardmetals - Metallographic determination of microstructure - Part 2: Measurement of WC grain size (ISO 4499-2:2020)

DIN EN ISO 4499-2:2020 硬质合金. 显微组织的金相学测定. 第2部分: WC颗粒尺寸的测量(ISO 4499-2-2020); 德文版本EN ISO 4499-2-2020

This document gives guidelines for the measurement of hardmetal grain size by metallographic techniques only using optical or electron microscopy. It is intended for sintered WC/Co hardmetals (also called cemented carbides or cermets) containing primarily WC (de: Wolframcarbid, e

Hardmetals - Metallographic determination of microstructure - Part 2: Measurement of WC grain size (ISO 4499-2:2020); German version EN ISO 4499-2:2020