77.120.70 镉、钴及其合金 标准查询与下载

GB/T 1485-1979 铂铑合金化学分析方法

本法适用于分析铂铑合金中5～70％铑。

Method for chemical analysis of platinum-rhodium alloys

GB/T 1486-1979 铂钌合金化学分析方法

试样用封管氯化法溶解，以硫脲分光光度法测定钉，铂对钉的显色有微小负干扰，可在绘制钉的标准曲线时加入一定量的铂以消除之。 本法适用于分析铂钉合金中5～10%钉。

Method for chemical analysis of platinum-ruthenium alloys

GB/T 1488-1979 铂钯铑合金化学分析方法

试样用硝酸及盐酸溶解，加盐酸赶除硝酸，用溴酸钠氧化，在碳酸氢钠（pH8）溶液中，钯、铑呈水合氧化物形式沉淀，铂却留在溶液中。滤出沉淀溶于盐酸中，再重复溴酸钠氧化沉淀一次，使钯、铑与铂完全分离。再将钯、铑的沉淀溶于盐酸中，在约3％盐酸溶液中，加丁二肟乙醇溶液沉淀钯，过滤与铑分离，用烘干丁二肟钯的沉淀的重量法测定钯量。滤液中的铑量，用氯化亚锡分光光度法测定之。 本方法适用于分析铂钯铑合金中4％钯及3.5％铑。

Method for chemical analysis of platinum-palladium-rhodium alloys

T/QGCML 2197-2023 电解钴

本文件规定了电解钴的分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存等内容。 本文件适用于电解钴。

Electrolytic cobalt

YS/T 1057.4-2022 四氧化三钴化学分析方法 第4部分：钾和钠含量的测定 火焰原子吸收光谱法和电感耦合等离子体原子发射光谱法

本文件适用于四氧化三钴中钾和钠含量的测定。方法一测定范围：钾：0.001 %～0.27 %，钠：0.001%～0.15 %；。方法二测定范围：钾：0.001 %～0.27 %，钠：0.001%～0.15 %。

Methods for chemical analysis of cobalt tetroxide Part 4: Determination of potassium and sodium content Flame atomic absorption spectrometry and inductively coupled plasma atomic emission spectrometry

YS/T 1057.3-2022 四氧化三钴化学分析方法 第3部分：硅含量的测定 电感耦合等离子体原子发射光谱法

本文件适用于四氧化三钴中硅含量的测定，测定范围0.0005%～0.50 %。

Methods for chemical analysis of cobalt tetroxide Part 3: Determination of silicon content by inductively coupled plasma atomic emission spectrometry

YS/T 1057.5-2022 四氧化三钴化学分析方法 第5部分：碳含量的测定 高频燃烧-红外吸收光谱法

本文件适用于四氧化三钴中碳含量的测定。测定范围：0.005 %～0.50 %。

Methods for chemical analysis of cobalt tetroxide Part 5: Determination of carbon content High-frequency combustion-infrared absorption spectrometry

ASTM B440-12(2021) 镉的标准规范

1.1 This specification covers refined cadmium metal in slab, ball or stick form. 1.2 Toxicity—Warning: Soluble and respirable forms of cadmium may be harmful to human health and the environment in certain forms and concentrations. Therefore, ingestion and inhalation of cadmium should be controlled under the appropriate regulations of the U.S. Occupational Safety and Health Administration (OSHA). Cadmium-containing alloys and coatings should not be used on articles that will contact food or beverages, or for dental and other equipment that is normally inserted in the mouth. Similarly, if articles using cadmiumcontaining alloys or coatings are welded, soldered, brazed, ground, “flame-cut,” or otherwise heated during fabrication, adequate ventilation must be provided to maintain occupational cadmium exposure below the OSHA Permissible Exposure Level (PEL). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cadmium

KS D 2608-2020 钼材料化学分析方法

Methods for chemical analysis of molybdenum materials

KS D 2607-2020 钨材料化学分析方法

Methods for chemical analysis of tungsten materials

YS/T 1057.2-2020 四氧化三钴化学分析方法 第2部分：氯离子含量的测定 离子选择性电极法

Methods for chemical analysis of cobalt tetroxide Part 2: Determination of chloride ion content Ion selective electrode method

KS D 2365-2019 锆粉

Zirconium powder

KS D 1710-2019 对银条的化学分析方法

Methods for chemical analysis of silver bullion

YS/T 1330.3-2019 钴铬烤瓷合金化学分析方法 第3部分：硅含量的测定 硅钼蓝分光光度法

Methods for chemical analysis of cobalt-chromium porcelain alloys Part 3: Determination of silicon content Silicon-molybdenum blue spectrophotometry

YS/T 1330.1-2019 钴铬烤瓷合金化学分析方法 第1部分：钴含量的测定 碘量法和电位滴定法

Methods for chemical analysis of cobalt-chromium porcelain alloys Part 1: Determination of cobalt content by iodometry and potentiometric titration

YS/T 1330.2-2019 钴铬烤瓷合金化学分析方法 第2部分：铬含量的测定 硫酸亚铁铵滴定法

Methods for chemical analysis of cobalt-chromium porcelain alloys Part 2: Determination of chromium content Ferrous ammonium sulfate titration method

YS/T 1330.4-2019 钴铬烤瓷合金化学分析方法 第4部分：钨、钼、铁、钌、镓、镉、铍、镍含量的测定 电感耦合等离子体原子发射光谱法

Methods for chemical analysis of cobalt-chromium porcelain alloys Part 4: Determination of tungsten, molybdenum, iron, ruthenium, gallium, cadmium, beryllium and nickel contents by inductively coupled plasma atomic emission spectrometry

YS/T 1287-2018 高纯镉化学分析方法 镁、铝、钙、铬、铁、镍、铜、锌、银、锡、锑、铅、铋量的测定 电感耦合等离子体质谱法

High purity cadmium chemical analysis method Determination of magnesium, aluminum, calcium, chromium, iron, nickel, copper, zinc, silver, tin, antimony, lead and bismuth by inductively coupled plasma mass spectrometry

GOST 123-2018 钴 规范

Cobalt. Specifications

NB/T 20008.27-2017 压水堆核电厂用其他材料 第27部分：控制棒驱动机构用ZCoCr29W4.5铸件

Other materials for pressurized water reactor nuclear power plants Part 27: ZCoCr29W4.5 castings for control rod driving mechanisms