79.120.10 木工机械 标准查询与下载

GB/T 14712-1993 单层热压机

本标准规定了单层热压机的主参数、精度、技术要求、试验方法、检验规则以及包装、标志和贮存。 本标准适用于生产刨花板的单层热压机。

Single-opening press

GB/T 14387-1993 纵剖木工圆锯机精度

本标准规定了纵剖木工圆锯机的几何精度和工作精度。 本标准适用于手动进给单锯片纵剖木工圆锯机。

Woodworking machines. Ripping circular saws. Accuracy tests

GB/T 14386-1993 木工平压两用刨床 精度

本标准规定了木工平压两用刨床的几何精度和工作精度。 本标准适用于木工平压两用刨床。

Woodworking machines. Surface planing and thicknessing machines. Accuracy tests

GB/T 14385-1993 单面木工压刨床 精度

本标准规定了单面木工压刨床的几何精度和工作精度。 本标准适用于单面木工压刨床。

Woodworking machines. Thickness planing machines with rotary cutterblock for one side dressing. Accuracy tests

GB/T 14388-1993 木工硬质合金圆锯片

本标准规定了木工硬质合金圆锯片的型式和尺寸、技术要求、试验方法和标志包装的基本要求。 本标准适用于直径100～630mm锯切木材，人造板、塑料及有色金属等的木工硬质合金圆锯片（以下简称锯片）。

Tungsten carbide tipped circular saw blade for woodworking

GB/T 14384-1993 木工机床 通用技术条件

本标准规定了木工机床（以下简称机床）设计、制造和验收的基本要求。 本标准适用于木工机床。

Woodworking machines. General specifications

GB/T 14303-1993 万能木工圆锯机精度

本标准规定了万能木工圆锯机的几何精度和工作精度。 本标准适用于锯片直径小于等于500mm的单锯片万能木工圆锯机。

Woodworking machines-Single blade universal circular saw bench with or without travelling table-Accuracy tests

GB/T 13570-1992 单轴木工铣床 精度

本标准规定了单轴木工铣床的几何精度和工作精度。 本标准适用于立式单轴木工铣床。

Woodworking machines--Single spindle moulding machines--Accuracy tests

GB/T 13571-1992 立式单轴木工钻床 精度

本标准规定了立式单轴木工钻床的几何精度和工作精度。 本标准适用于一般用途的立式单轴木工钻床。

Woodworking machines--Single spindle boring machines--Accuracy tests

GB/T 13572-1992 二、三、四面木工刨床 精度

本标准规定了二、三、四面木工刨床的几何精度和工作精度。 本标准适用于一般用途的二、三、四面木工刨床。

Woodworking machines--planing machines for two,three or four-side dresing--Accuracy test

GB/T 13569-1992 木工平刨床 精度

本标准规定了木工平刨床的几何精度和工作精度。 本标准适用于木工平刨床。

Woodworking machines--Surface planing machines with cutterblock for one side dressing--Accuracy tests

GB/T 13568-1992 细木工带锯机 精度

本标准规定了细木工带锯机的几何精度和工作精度。 本标准适用于细木工带锯机。

Woodworking machines Table bandsawing machines Accuracy tests

GB/T 12448-1990 木工机床型号编制方法

本标准规定了木工机床的类、组、系的划分及其型号表示方法。 本标准适用于各类木工机床。

Woodworking machines--Technical classification of woodworking machines and auxiliary machines for woodwooking

GB/T 10960-1989 锯片往复木工锯板机 精度

本标准规定了最大加工长度大于等于2000mm的锯片往复木工锯板机的精度。 本标准适用于最大加工长度大于等于2000mm的锯片往复木工锯板机。

Woodworking machines--Single blade stroke circular sawing machines--Accuracy tests

GB/T 10961-1989 木工机床操作指示形象化符号

本标准规定了木工机床操作指示标牌和控制系统上的一些形象化符号。 本标准适用于所有木工机床的操作指示标牌、操作面板和标志。

Symbols for indications appearing on woodworking machinery

GB/T 10959-1989 带移动工作台木工锯板机 精度

本标准规定了最大加工长度大于等于2000mm的带移动工作台木工锯板机的精度。 本标准适用于最大加工长度大于等于2000mm带移动工作台木工锯板机。

Woodworking machines--Single blade circular sawing machines with travelling table--Accuracy tests

T/CASMES 289-2024 数控多功能木工六面钻

本文件规定了数控多功能木工六面钻的基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

CNC multifunctional woodworking six sided drill

T/QGCML 2660-2023 硬质合金圆锯片

本文件规定了硬质合金圆锯片的术语和定义、型式和尺寸、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于外径为500 mm，内径为30 mm的硬质合金材质的圆锯片（以下简称锯片）。

Carbide circular saw blade

T/CASMES 127-2022 木工硬质合金镂铣刀

本文件规定了木工硬质合金镂铣刀的分类及代号、原材料要求、技术要求、检验方法、检验规则、标志、包装、贮运。 本文件适用于铣削木材及木质构件用的木工硬质合金镂铣刀（以下简称“镂铣刀”）。

Carbide router bit for woodworking

GSO ISO 19085-4:2022 木工机械 安全 第4部分：立式板材圆锯机

ISO 19085-4:2018 gives the safety requirements and measures for manually loaded and unloaded stationary vertical panel sawing machines, hereinafter referred to as "machines". NOTE 1 In manual loading, the operator puts the work-piece directly onto the work-piece support, with no intermediate loading device to receive and transfer the work-piece from the operator to the cutting position. In manual unloading, the operator removes the work-piece directly from the work-piece support, with no intermediate unloading device to transfer the work-piece from the cutting position to the operator. ISO 19085-4:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. ISO 19085-4:2018 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - an integrated feed device; - a device for scoring; - an angle cutting device; - a middle support device; - programmable end stops for parallel vertical cuts; - a device for grooving with a width of at most 20 mm in one pass by using a milling tool; and - a panel pusher. The machines are designed for cutting panels consisting of: a) solid wood; b) material with similar physical characteristics to wood (see ISO 19085‑1:2017, 3.2); c) composite materials with core consisting, for example, of polyurethane or mineral material laminated with light alloy; d) polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials; and e) gypsum boards, gypsum bounded fibreboards. ISO 19085-4:2018 does not apply to machines - with pressure beam and saw unit mounted behind the work-piece support; - where the guide rails on which the saw unit moves vertically are fixed on the machine frame and the horizontal cut can only be made by manually feeding the panel; - designed to cut in vertical direction only; - which are displaceable; - automatically performing two or more cutting cycles in sequence; - intended for use in potentially explosive atmosphere; and - manufactured before the date of its publication.

Woodworking machines — Safety — Part 4: Vertical panel circular sawing machines