79.120.10 木工机械 标准查询与下载

ISO 19085-7:2019 木工机械.安全性.第7部分:表面刨削 厚度刨削 组合表面/厚度刨削机

This document gives the safety requirements and measures for stationary and displaceable — surface planing machines, also called jointers, — thickness planing machines, also called planers or single surface planers, — combined surface/thickness planing machines with fixed cutterblock position, with an integrated feed in thicknessing mode, with or without demountable power feed device in planing mode and with manual loading and unloading of the work- piece, hereinafter referred to as “machines”. The machines are designed to cut solid wood and material with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085-1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100. It is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with. This document does not apply to: a) machines with more than one cutterblock; b) machines with mortising unit driven by a separate motor; c) machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode; d) machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units; e) machines where surfacing and thicknessing can be performed on the same section of the cutterblock at the same time; f) machines intended for use in potentially explosive atmosphere; g) machines manufactured before the date of its publication as an international standard; h) displaceable machines with a maximum planing width of ≤330 mm. NOTE 3 Transportable motor-operated electric tools are dealt with in IEC 62841-1:2014 and IEC 61029-2-3:1993. 

Woodworking machines — Safety — Part 7: Surface planing, thickness planing, combined surface/thickness planing machines

ISO 19085-9:2019 木工机械 - 安全 - 第9部分:圆锯台（带和不带滑台）

This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as “table saws” (in the USA), hereinafter referred to as “machines”, designed to cut wood and material with similar physical characteristics to wood. NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085-1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with: — device for the main saw blade and scoring saw blade to be raised and lowered through the table; — device to tilt the main saw blade and scoring saw blade for angled cutting; — device for scoring; — device for grooving with milling tool with a width not exceeding 20 mm in one pass; — demountable power feed unit; — additional manually operated sliding table; — powered work-piece clamping device. NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving. This document does not apply to: a) transportable/displaceable machines intended for outdoor use on building sites; NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085-10:2018. b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines intended for use in a potentially explosive atmosphere; d) machines manufactured before the date of its publication as an International Standard; e) transportable machines with a maximum saw blade diameter of ≤315 mm. NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841-1:2014 and IEC 62841- 3-1:2014. 

Woodworking machines — Safety — Part 9: Circular saw benches (with and without sliding table)

BS EN 16770:2018 木工机械的安全 用于室内安装的切屑和除尘系统 安全要求

What is BS EN 16770 - Chip and dust extraction systems about?    BS EN 16770 discusses the safety of woodworking machines. This European standard helps its users of the woodworking industry to create a safe work environment for the workers by ensuring the machinery meets the minimum safety requirements.    BS EN 16770 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant for chip and dust extraction systems for indoor use designated to be connected to woodworking machines, when they are used as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse.   Note1: BS EN 16770 does not apply to: 

Safety of woodworking machines. Chip and dust extraction systems for indoor installation. Safety requirements

DIN EN ISO 19085-8:2018 木工机械 安全 第8部分：直工件砂带打磨和校准机（ISO 19085-8:2017）；德文版 EN ISO 19085-8:2018

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to machines used to calibrate and/or to sand panels and/or linear work-pieces consisting of solid wood and material with similar physical characteristics to wood, gypsum boards and gypsum bounded fibreboards, fitted with an integrated feed and sanding belt(s) positioned over and/or under the work-piece level and working in the panel feed direction, hereinafter referred to as "machines", when they are operated, adjusted and aintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Loading and/or unloading is manual or automatic. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

Woodworking machines - Safety - Part 8: Belt sanding and calibrating machines for straight workpieces (ISO 19085-8:2017); German version EN ISO 19085-8:2018

NF E64-600-2:2018 木工机械.安全.第2部分:水平梁板圆锯机

La série de normes NF EN ISO 19085 traite de la sécurité des Machines à bois.La présente partie fixe les règles de sécurité spécifiques aux scies circulaires à panneaux horizontales à presseur.Elle doit être utilisée conjointement avec la NF EN ISO 19085-1.Le présent document vise à donner présomption de conformité à la Directive "Machines" 2006/42/CE.

Woodworking machines - Safety - Part 2 : horizontal beam panel circular sawing machines

DIN EN ISO 19085-3:2018 木工机械.安全要求.第3部分:数控（NC）镗铣机(ISO 19085-3-2017);德文版本EN ISO 19085-3-2017

This international standard deals with all significant hazards, hazardous situations and events, relevant to NC boring machines, NC routing machines and NC combined boring/routing machines, designed to cut solid wood and material with similar physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.

Woodworking machines - Safety requirements - Part 3: Numerically controlled (NC) boring and routing machines (ISO 19085-3:2017); German version EN ISO 19085-3:2017

ISO 19085-10:2018 木工机械 - 安全 - 第10部分:建筑工地锯（承包商）

This document gives the safety requirements and measures for displaceable building site saws, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as “machines”. NOTE 1 For the definition of displaceable machine, see ISO 19085-1:2017, 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. The machine can also be fitted with a device for the saw blade to be manually raised and lowered through the table, whose hazards have been dealt with. This document does not apply to the following: a) machines with a maximum saw blade diameter smaller than 350 mm or greater than 500 mm; b) hand-held woodworking machines, including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines with a device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table; NOTE 3 Hand-held motor-operated electric tools are covered by IEC 62841-1 together with IEC 62841-2-5. NOTE 4 Machines with the device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table are considered as table saws, covered by This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

Woodworking machines — Safety — Part 10: Building site saws (contractor saws)

JB/T 9947-2018 木工销孔钻

Woodworking pin hole drill

JB/T 13375-2018 液压式拼板机

Hydraulic puzzle machine

JB/T 8341-2018 木工硬质合金直刃镂铣刀

Carbide straight edge router bit for woodworking

JB/T 13373-2018 表板拼板机

Table board puzzle machine

JB/T 3377-2018 木工机用直刃刨刀

Straight edge planer for woodworking machines

JB/T 8776-2018 木工硬质合金圆弧铣刀

Carbide arc milling cutter for woodworking

JB/T 5735-2018 木工圆盘槽铣刀

Woodworking disc groove milling cutter

JB/T 5736-2018 木工双齿榫槽铣刀

Woodworking double tooth tongue and groove milling cutter

JB/T 9952-2018 木工平刨床 噪声声功率级限值

Woodworking planer noise sound power level limit

JB/T 13374-2018 排钻快速接头

Row drilling quick connector

DIN EN 1870-6:2018 木材加工机械的安全性.圆形锯床.第6部分:柴火加工用圆形锯床;德文版本EN 1870-6-2017

This document deals with all significant hazards, hazardous situations and events which are relevant to firewood and dual-purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading, designed to cut solid wood. On Combined circular sawing machines for firewood - Log splitting machines only the circular sawing machine for firewood is covered by this European Standard.

Safety of woodworking machines - Circular sawing machines - Part 6: Circular sawing machines for fire wood; German version EN 1870-6:2017

DIN EN ISO 19085-1:2018 木工机械.安全.第1部分:通用要求(ISO 19085-1-2017);德文版本EN ISO 19085-1-2017

This International Standard is applicable to woodworking machines with cutting tools and/or sanding tools as defined in 3.1 when they are used as intended and under the conditions foreseen by the manufacturer. This document contains the safety requirements and measures to reduce risks related to woodworking machines arising during operation, adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping: those that are common to most of such machines.

Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:2017); German version EN ISO 19085-1:2017

DIN EN ISO 19085-5:2018 木工机械.安全.第5部分:维度锯(ISO 19085-5-2017);德文版本EN ISO 19085-5-2017

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable dimensions saws, designed to cut wood and material with similar physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.

Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2017); German version EN ISO 19085-5:2017