83.160.99 标准查询与下载

GB/T 10824-2008 充气轮胎轮辋实心轮胎技术规范

本标准规定了充气轮胎轮辋实心轮胎的术语和定义、要求、试验方法和标志。 本标准适用于平衡重式叉车、起升机、牵引车、装载机、平板车和固定平台搬运车等车辆上使用的充气轮胎轮辋实心轮胎。

Technical specincationof solid tyres for pnemnatic tyres rims

GB 12836.2-2003 无内胎气门嘴 第2部分;压紧式气门嘴

GB 12836的本部分规定了无内胎压紧式气门嘴（以下简称气门嘴）的型号标记、结构型式、零件的类型、结构尺寸及材料、技术要求、试验方法、检验规则、标志、包装及贮存。 本部分适用于摩托车、轿车、轻型载重汽车、载重汽车及客车无内胎轮胎用气门嘴。 本部分不适用于航空轮胎气门嘴。

Tubeless valves Part 2: Clamp-in valves

GB/T 2883-2002 工程机械轮辋规格系列

本标准规定了工程机械轮辋的代号、轮廓和尺寸。 本标准适用于工程机械轮辋。

Rims series for earth-mover

GB/T 2982-2001 工业车辆充气轮胎规格、尺寸、气压与负荷

本标准规定了工业车辆充气轮胎规格、尺寸、气压与负荷。本标准适用于平衡配重式叉车、牵引车和平板车等工业车辆充气轮胎。

Designation,dimensions,inflation pressure and load capacity of pneumatic tyres for industrial vehicles

GB/T 2980-2001 工程机械轮胎规格、尺寸、气压与负荷

本标准规定了工程机械轮胎的规格、尺寸、气压与负荷、花纹分类及设计花纹深度。 本标准适用于重型自卸车、装载机、挖掘机、平地机、铲运机、推土机、起重机和压路机等工程机械用充气轮胎。

Designation,dimensions,Inflation pressure and load for earth-mover tyres

T/CSTE 0563-2024 质量分级及“领跑者”评价要求 工业车辆充气轮胎

本文件规定了工业车辆充气轮胎产品质量分级及企业标准水平评价的基本要求、评价指标及要求、评 价方法及等级划分。 本文件适用于工业车辆充气轮胎产品质量分级及企业标准水平评价。相关机构开展质量分级和企业标 准水平评价、“领跑者”产品评价以及相关认证或评价时可参照使用，相关企业在制定企业标准时也可参 照本文件。

Assessment requirements for quality grading and forerunner — Pneumatic tyres for industrial vehicles

BS ISO 4250-1:2023 推土机轮胎和轮辋 轮胎名称和尺寸

1   Scope This document specifies designations and dimensions for earth-mover tyres and gives the recommended rims primarily intended for earth-moving machinery as defined in ISO 6165.

Earth-mover tyres and rims. Tyre designation and dimensions

BS ISO 4250-2:2023 推土机轮胎和轮辋 负荷和通货膨胀压力

1   Scope This document gives working definitions of masses and load cycles and specifies tyre loads and reference inflation pressures for tyres primarily intended for earth-mover machines.

Earth-mover tyres and rims. Loads and inflation pressures

ISO 4250-1:2023 土方机械轮胎和轮辋.第1部分:轮胎命名和尺寸规格

This document specifies designations and dimensions for earth-mover tyres and gives the recommended rims primarily intended for earth-moving machinery as defined in ISO 6165.

Earth-mover tyres and rims — Part 1: Tyre designation and dimensions

ISO 4250-2:2023 土方机械轮胎和轮辋.第2部分:载重和充气压力

This document gives working definitions of masses and load cycles and specifies tyre loads and reference inflation pressures for tyres primarily intended for earth-mover machines.

Earth-mover tyres and rims — Part 2: Loads and inflation pressures

KS M ISO 10499-1-2022 工业轮胎和轮辋充气轮胎轮辋用橡胶实心轮胎（米制系列）第1部分:名称、尺寸和标记

Industrial tyres and rims Rubber solid tyres(metric series) for pneumatic tyre rims Part 1: Designation, dimensions and marking

KS M ISO 3739-2-2022 工业轮胎和轮辋第2部分:5度锥形或平底轮辋上的充气轮胎（米制系列）额定载荷

Industrial tyres and rims Part 2: Pneumatic tyres(metric series) on 5 degrees tapered or flat base rims Load ratings

ISO 3739-1:2022 工业轮胎和轮辋.第1部分:5度锥形或平底轮辋上的充气轮胎（米制系列）.名称、尺寸和标记

This document specifies the main requirements of the metric series of pneumatic tyres primarily intended for indus trial vehicles, including designations, dimensions and markings . The tyres are based on the following parameters: — speeds not exceeding 50 km/h; — use on 5° tapered or flat base rims . The conversion of code-designated indus trial tyres into metric-designated tyres is outside the scope of this document.

Industrial tyres and rims — Part 1: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Designation, dimensions and marking

GSO ISO 10499-1:2022 工业轮胎和轮辋 充气轮胎轮辋用橡胶实心轮胎（公制系列） 第1部分：名称、尺寸和标记

This document specifies the main requirements, including designations, dimensions and markings, of the metric series of rubber solid tyres for pneumatic tyre rims primarily intended for industrial machines for use on prepared surfaces. Rim contours fitting these tyres are specified in ISO 3739-1 and ISO 3739-3.

Industrial tyres and rims — Rubber solid tyres (metric series) for pneumatic tyre rims — Part 1: Designation, dimensions and marking

KS M ISO 10499-2-2022 工业轮胎和轮辋 充气轮胎轮辋用实心橡胶轮胎（公制系列） 第2部分：额定载荷

Industrial tyres and rims－Rubber solid tyres(metric series)for pneumatic tyre rims－Part 2：Load ratings

KS M ISO 10500-2022 工业轮胎和轮辋 圆柱和圆锥基橡胶实心轮胎（公制系列） 名称、尺寸和标记

Industrial tyres and rims－Cylindrical and conical base rubber solid tyres(metric series)－Designation, dimensions and marking

BS ISO 3739-2:2021 工业轮胎和轮辋 5度锥形或平底轮辋上的充气轮胎（公制系列） 额定负载

Industrial tyres and rims. Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims. Load ratings

GSO ISO 4250-2:2021 土方机械轮胎和轮辋 第2部分：负载和充气压力

The ISO 4250 series consists of three parts laying down the technical designation and dimensions of tyres and rims for earth-movers; it also gives load tables for these tyres. This document gives working definitions of masses and load cycles and specifies tyre loads and reference inflation pressures for narrow- and wide-base tyres primarily intended for earth-mover machines.

Earth-mover tyres and rims — Part 2: Loads and inflation pressures

ISO 3739-2:2021 工业车辆轮胎和轮辋. 第2部分: 5°或平底轮辋的充气轮胎(米制系列). 额定负荷

This document specifies the load ratings of the metric series of pneumatic tyres primarily intended for industrial vehicles for use on prepared surfaces. these tyres.

Industrial tyres and rims - Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims - Load ratings

KS M ISO 4250-1-2021 地球摩天轮胎和轮辋 - 第1部分:轮胎指定和尺寸

Earth-mover tyres and rims —Part 1: Tyre designation and dimensions