83.160.99 标准查询与下载

GSO ISO 10500:2013 工业轮胎和轮辋 圆柱形和圆锥形橡胶实心轮胎（公制系列） 名称、尺寸和标记

This International Standard specifies the main requirements, including designations, dimensions, markings and load ratings, of the metric series of cylindrical and conical base rubber solid tyres primarily intended for industrial machines for use on prepared surfaces

Industrial tyres and rims -- Cylindrical and conical base rubber solid tyres (metric series) -- Designation, dimensions and marking

GSO ISO 3739-1:2013 工业轮胎和轴环 第1部分：五级锥度或平底轴环上的充气轮胎（公制系列） 标识、尺寸和标记

This part of ISO 3739 specifies the main requirements of the metric series of pneumatic tyres primarily intended for industrial vehicles, including designations, dimensions and markings. The tyres are based on the following parameters: — speeds not exceeding 50 km/h; — use on 5° tapered or flat base rims. The conversion of code-designated industrial tyres into metric-designated tyres is outside the scope of this part of ISO 3739.

Industrial tyres and rims -- Part 1: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims -- Designation, dimensions and marking

GSO ISO 3739-2:2013 工业轮胎和轴环 第 II 部分：五级锥度和平底轴环上的充气轮胎（公制系列） 额定载荷

This part of ISO 3739 specifies the load ratings of the metric series of pneumatic tyres primarily intended for industrial vehicles for use on prepared surfaces. ISO 3739-1 deals with designation, dimensions and marking; ISO 3739-3 deals with rim contours for these tyres.

Industrial tyres and rims -- Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims -- Load ratings

SNI 3768-2013 硫化轮胎

Ban vulkanisi

GSO ASTM F1923:2010 低速非公路充气轮胎的标准试验方法

1.1 This test method covers measurements for comparative tire strength and dimensional characteristics. This test method covers new and retreaded pneumatic tires, both tube and tubeless types, and flaps when applicable, for mounting on construction, earthmoving, mining and logging equipment, graders, mobile cranes, and similar vehicles operated at low speeds off the road. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Tires, Pneumatic, Low Speed, Off Highway

KS M 6751-2009 工业车和建筑用车轮胎

이 표준은 산업 차량용 및 건설 차량용 타이어(이하 타이어라 한다.)에 대하여 규정한다.

Rubber tires for industrial vehicles and off the road service

KS M ISO 3739-1-2009(2019) 工业轮胎和轮辋第1部分:5°锥形或平底轮辋上的充气轮胎（米制系列）名称、尺寸和标记

Industrial tyres and rims－Part 1：Pneumatic tyres(metric series) on 5° tapered or flat base rims－Designation, dimensions and marking

KS M ISO 3739-1:2009 工业用轮胎和轮辋.第1部分:5锥度或平底轮辋的可充气轮胎(米制系列).名称、尺寸和标志

이 표준은 산업용 차량에 우선적으로 적용되는 공기 타이어 메트릭 시리즈의 호칭, 치수 및

Industrial tyres and rims－Part 1：Pneumatic tyres(metric series) on 5° tapered or flat base rims－Designation, dimensions and marking

KS M ISO 3739-2-2007(2017) 工业轮胎和轮辋第2部分:5°锥形或平底轮辋充气轮胎（米制系列）额定载荷

Industrial tyres and rims－Part 2：Pneumatic tyres(metric series) on 5° tapered or flat base rims－Load ratings

KS M ISO 3739-2:2007 工业用轮胎和轮辋.第2部分:5锥度或平底轮辋的可充气轮胎(米制系列).额定负荷

이 규격은 준비된 표면에 사용하는 산업용 차량에 우선적으로 적용되는 공기 타이어 메트릭 시

Industrial tyres and rims－Part 2：Pneumatic tyres(metric series) on 5° tapered or flat base rims－Load ratings

KS M ISO 10500-2007(2022) 工业轮胎和轮辋－圆柱和圆锥基橡胶实心轮胎（米制系列）－名称、尺寸和标记

Industrial tyres and rims－Cylindrical and conical base rubber solid tyres(metric series)－Designation, dimensions and marking

KS M ISO 10500-2007(2017) 工业轮胎和轮辋圆柱和圆锥基橡胶实心轮胎（米制系列）名称、尺寸和标记

Industrial tyres and rims－Cylindrical and conical base rubber solid tyres(metric series)－Designation, dimensions and marking

KS M ISO 10499-1-2007(2017) 工业轮胎和轮辋充气轮胎轮辋用实心轮胎（米制系列）第1部分:名称、尺寸和标记

Industrial tyres and rims－Solid tyres(metric series) for pneumatic tyre rims－Part 1：Designation, dimensions and marking

KS M ISO 10499-2:2007 工业用轮胎和轮辋.充气胎轮辋用橡胶实心轮胎(米制系列).第2部分:荷载额定值

이 규격은 준비된 표면에 사용하는 산업용 차량에 우선적으로 적용하기 위한 공기 타이어 림용

Industrial tyres and rims－Rubber solid tyres(metric series)for pneumatic tyre rims－Part 2：Load ratings

KS M ISO 10499-2-2007(2022) 工业轮胎和轮辋－充气轮胎轮辋用橡胶实心轮胎（米制系列）－第2部分:额定载荷

Industrial tyres and rims－Rubber solid tyres(metric series)for pneumatic tyre rims－Part 2：Load ratings

KS M ISO 10499-2-2007(2017) 工业轮胎和轮辋充气轮胎轮辋用橡胶实心轮胎（米制系列）第2部分:额定载荷

Industrial tyres and rims－Rubber solid tyres(metric series)for pneumatic tyre rims－Part 2：Load ratings

KS M ISO 10500:2007 工业用轮胎和轮辋.圆柱基和圆锥基橡胶实心轮胎(米制系列)命名、尺寸和标志

이 규격은 준비된 표면에 사용하는 산업용 기계에 우선적으로 적용되는 원통형과 원뿔형 베이스

Industrial tyres and rims-Cylindrical and conical base rubber solid tyres(metric series)-Designation, dimensions and marking

KS M ISO 10499-1:2007 工业车辆轮胎和轮辋.充气轮胎轮辋用实心轮胎(米制系列).第1部分:命名、尺寸和标记

이 규격은 채비가 되어 있는 표면 위에서 사용되는 산업용 기계에 일차적으로 적용하기 위하여

Industrial tyres and rims－Solid tyres(metric series) for pneumatic tyre rims－Part 1：Designation, dimensions and marking

HG/T 3979-2007 工程机械翻新轮胎

本标准规定了工程机械翻新轮胎用术语和定义、技术要求、检测方法、检验规则和标志。 本标准适用于工程机械车辆用充气轮胎的翻新。

Retreaded tyre for earth-mover

BS ISO 3739-1:2007 工业轮胎和轮辋.5°锥形轮辋或平面轮辋上的充气轮胎(公制系列).名称与符号,尺寸规格和标记

This part of ISO 3739 specifies the main requirements of the metric series of pneumatic tyres primarily intended for industrial vehicles, including designations, dimensions and markings. The tyres are based on the following parameters: speeds not exceeding 50 km/h; use on 5° tapered or flat base rims. The conversion of code-designated industrial tyres into metric-designated tyres is outside the scope of this part of ISO 3739.

Industrial tyres and rims. Pneumatic tyres (metric series) on 5 tapered on flat base rims. Designation, dimensions and marking