91.080.40 混凝土结构 标准查询与下载

JG/T 560-2019 建筑用槽式预埋组件

　　现批准《建筑用槽式预埋组件》为建筑工业行业产品标准，编号为JG/T560-2019，自2019年9月1日起实施。 　　本标准在住房和城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房和城乡建设部标准定额研究所组织中国标准出版社出版发行。 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2019年3月4日  

Trough type embedded components for construction

ASTM E1966-15(2019) 耐火接头系统的标准试验方法

1.1 This fire-test-response test method measures the performance of joint systems designed to be used with fire rated floors and walls during a fire endurance test exposure. The fire endurance test end point is the period of time elapsing before the first performance criteria is reached when the joint system is subjected to one of two time-temperature fire exposures. 1.2 The fire exposure conditions used are either those specified by Test Method E119 for testing assemblies to standard time-temperature exposures or Test Method E1529 for testing assemblies to rapid-temperature rise fires. 1.3 This test method specifies the heating conditions, methods of test, and criteria for the evaluation of the ability of a joint system to maintain the fire resistance where hourly rated fire-separating elements meet. 1.4 Test results establish the performance of joint systems during the fire-exposure period and shall not be construed as having determined the joint systems suitability for use after that exposure. 1.5 This test method does not provide quantitative information about the joint system relative to the rate of leakage of smoke or gases or both. However, it requires that such phenomena be noted and reported when describing the general behavior of joint systems during the fire endurance test but is not part of the conditions of compliance. 1.6 Potentially important factors and fire characteristics not addressed by this test method include, but are not limited to: 1.6.1 The performance of the fire-resistive joint system constructed with components other than those tested. 1.6.2 The cyclic movement capabilities of joint systems other than the cycling conditions tested. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.9 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.10 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1 This test method is under the jurisdiction of ASTM Committee E05 on Fire Standards and is the direct responsibility of Subcommittee E05.11 on Fire Resistance. Current edition approved March 1, 2019. Published March 2019. Originally approved in 1998. Last previous edition approved in 2015 as E1966 – 15. DOI: 10.1520/E1966-15R19. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Fire-Resistive Joint Systems

ASTM F2170-19 用原位探头测定混凝土楼板相对湿度的标准试验方法

Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes

ASTM D7705/D7705M-12(2019) 用于混凝土结构的纤维增强聚合物（FRP）基体复合材料的耐碱性的标准试验方法

1.1 This test method covers the procedure for evaluating the alkali resistance of FRP bars used as reinforcing bars in concrete. Alkali resistance is measured by subjecting the FRP bars to an aqueous alkali environment, with or without sustained tensile stress, and then testing them to failure in tension according to Test Method D7205/D7205M. This standard presents three procedures conducted at a moderately elevated temperature of 60 ºC (140 ºF), each defining different loading conditions. The test method is also appropriate for use with linear segments of FRP reinforcements cut from twoor three-dimensional reinforcing grid. 1.2 The values stated in either inch-pound units or SI units shall be regarded separately as the standard. The inch-pound units are shown in the parentheses. The values stated in each system are not exact equivalents; therefore each system shall be used independently of each other. Combining values from the two systems may result in non-conformance. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction

DB21/T 2572-2019 装配式混凝土结构设计规程

Code for Design of Prefabricated Concrete Structures

DB21/T 3101-2019 建筑工程混凝土结构防腐技术规程

Technical specification for anticorrosion of concrete structures in construction engineering

ISO 16837:2019 无损检验.声发射检验.钢筋混凝土梁损伤评定的试验方法

Non-destructive testing — Acoustic emission testing — Test method for damage qualification of reinforced concrete beams

ISO 16836:2019 无损检测.声发射检测.混凝土中声发射信号的测量方法

This document establishes a measurement method for acoustic emission signals in concrete.

Non-destructive testing — Acoustic emission testing — Measurement method for acoustic emission signals in concrete

ISO 16838:2019 无损检测.声发射检测.混凝土结构中活动裂缝分类的试验方法

This document specifies a test method for classification of active cracks in concrete structures.

Non-destructive testing — Acoustic emission testing — Test method for classification of active cracks in concrete structures

ISO 13315-8:2019 混凝土和混凝土结构的环境管理 - 第8部分:混凝土的环境标签和声明

This document provides a general principle, procedures and requirements for environmental labels and declarations for concrete and concrete structures. It is used for the environmental labels and declarations for concrete constituents, reinforcement, concrete, concrete products and concrete structures. NOTE This document contains more specific requirements for environmental labels and declarations for concrete and concrete structures, based on ISO 14020, ISO 14024, ISO 14025 and ISO 21930. This document includes the following phases of concrete and concrete structures: — production phase of concrete constituents, concrete and concrete products; — execution phase of concrete structures; — use phase of concrete structures; and — end-of-life phase. This document applies to the partial life cycle (certain phases of the life cycle) or the entire life cycle of concrete and concrete structures. It applies to new concrete and concrete structures as well as to existing concrete and concrete structures.

Environmental management for concrete and concrete structures — Part 8: Environmental labels and declarations

DB42/T 1489-2018 后浇清水混凝土技术规程

Post-poured fair-faced concrete technical specification

DB42/T 1488-2018 岩石与混凝土自锁锚固技术规程

Technical specification for rock and concrete self-locking anchorage

DB11/T 1609-2018 预拌喷射混凝土应用技术规程

Technical specification for the application of ready-mixed shotcrete

T/ZS 0023-2018 装配式混凝土结构预制构件质量检验标准

前  言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  基本要求　 5  原材料检验　 5.1  一般要求　 5.2  混凝土　 5.3  钢筋与钢材　 5.4  保温材料与拉结件　 5.5  外装饰材料　 6  生产检验　 6.1  一般要求　 6.2  连接材料进厂（场）检验　 6.3  模具检验　 6.4  生产过程检验　 6.5  生产成品检验　 7  进场检验　 7.1  一般要求　 7.2  预制构件进场检验　 7.3  密封材料进场检验　 8  安装检验　

Quality inspection standard for prefabricated components of prefabricated concrete structures

ASTM C1602/C1602M-18 水硬性水泥混凝土生产用混合水的标准规范

1.1 This specification covers the compositional and performance requirements for water used as mixing water in hydraulic cement concrete. It defines sources of water and provides requirements and testing frequencies for qualifying individual or combined water sources. In any case where the requirements of the purchaser differ from these in this specification, the purchaser’s specification shall govern. 1.2 This specification does not purport to cover methods of storage, transportation, or blending of water, or to address the development and maintenance of quality control programs sponsored or managed by the manufacturer. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

ASTM D4259-18 涂覆前用磨蚀制备混凝土的标准实施规程

1.1 This practice includes surface preparation of concrete to prepare the surface prior to the application of coatings. 1.2 This practice is intended to create a surface profile in concrete and to remove foreign materials and weak surface laitance. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Concrete by Abrasion Prior to Coating Application

SL 775-2018 水工混凝土结构耐久性评定规范

Specification for durability assessment of hydraulic concrete structures

DB42/T 1483-2018 装配整体式混凝土叠合剪力墙结构技术规程

Technical specification for assembled monolithic concrete laminated shear wall structure

ASTM D7635/D7635M-18 用于测量织物加强层涂层厚度的标准测试方法

1.1 This test method covers measuring the thickness of the coating over fiber backing or reinforcing fabric. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement

ASTM D4263-83(2018) 用塑料板法指示混凝土中水分的标准试验方法

1.1 This test method is used to indicate the presence of capillary moisture in concrete. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific caution statements, see Section 4. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method