91.100.15 矿物材料和产品 标准查询与下载

T/QGCML 329-2022 煤矿井下快速密闭柔性材料

本文件规定了煤矿井下快速密封柔性材料的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于煤矿井下快速密闭柔性材料的生产及检验。

Quick sealing flexible material in underground coal mine

ASTM C616/C616M-22 砂岩规格石料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of quartz-based dimension stone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of quartz-based dimension stone. 1.2 Quartz-based dimension stone shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Quartz-Based Dimension Stone

ASTM C568/C568M-22 石灰石规格石料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of limestone for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of limestone dimension stone. 1.2 Dimension limestone shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units of composed fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Limestone Dimension Stone

ASTM C503/C503M-22 大理石规格石料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of marble for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of marble dimension stone. 1.2 Dimension marble shall include stone that is sawed, cut, split, or otherwise finished or shaped into blocks, slabs or tiles, and shall specifically exclude molded, cast and artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Marble Dimension Stone

ASTM C629/C629M-22 板岩规格石料的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of slate for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of slate dimension stone. 1.2 Dimension slate shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. 1.3 It specifically excludes roofing slate (see Specification C406/C406M) and slate for industrial uses. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Slate Dimension Stone

ASTM C406/C406M-22 石板屋顶的标准规格

1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of slate for use as roof shingles. 1.2 Slates not included in this specification are those containing soft carbonaceous ribbons. The wide variation in physical properties and composition of such ribbon slates render their service life uncertain under some conditions of use. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Roofing Slate

T/CBMF 194-2022 超细复合矿物掺合料

本文件规定了超细复合矿物掺合料的组分与材料、技术要求、试验方法、检验规则、包装、标志、运输和贮存等。 本文件适用于作水泥混合材、砂浆和混凝土掺合料的超细复合矿物掺合料。

Ultrafine compound mineral admixtures

ASTM D5106-22 沥青铺路混合料用钢渣集料的标准规范

1.1 This specification covers crushed steel slag coarse and fine aggregates suitable for use in asphalt paving mixtures. 1.2 Steel slag coarse and fine aggregates are currently being used entirely (Note 1) or combined with other mineral aggregates, such as those covered in Specification D692/ D692M or D1073, to produce paving mixtures similar to those described in Specification D3515 or D4215. NOTE 1—When 100 % of the coarse aggregate in an asphalt mixture is steel slag, the amount of steel slag fines in that mixture may be limited to prevent bulking. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. NOTE 2—Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. 1.4 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Slag Aggregates for Asphalt Paving Mixtures

ASTM C1405-22 釉面砖（单烧砖单元）标准规范

1.1 This specification covers brick, having a ceramic glaze finish fused to the body during the same process as the unit body firing, that are intended for use in masonry and supplying structural or facing components, or both, to the structure. This specification does not cover double-fired glazed brick. Some double-fired decorative glazes have physical properties, which vary from those of single-fired glazes due to the lower temperatures used in applying the decorative coating. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements of this specification is beyond the scope of this specification. 1.3 Glazed brick are prismatic units available in a variety of sizes, textures, colors, and shapes. Glazed brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see Terminology C1232). 1.4 Glazed brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5 Glazed brick are classified into one of two grades, one of two types, one of two classes, and one of three divisions. 1.6 Opacity of the glaze is not required unless specified by the purchaser. 1.7 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Glazed Brick (Single Fired, Brick Units)

ASTM D8038-16(2022)e1 再生骨料基层（RAB）材料再生的标准实施规程

1.1 This practice covers selected aspects for reclamation of recycled aggregate base (RAB) material derived from asphalt pavement or concrete. RAB may be called recycled asphalt pavement (RAP) or recycled concrete aggregate (RCA). 1.2 This practice is provided related to material quality, material quality control testing, and also operator and facility qualifications. 1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. NOTE 1—Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material

ASTM C217/C217M-22 板岩耐候性的标准试验方法

1.1 These test methods cover two procedures for weather resistance of slate in all outdoor installations by determining the depth of softening after soaking in 1 % sulfuric acid solution by a shear/scratch tester (Test Method A) or by hand scraping (Test Method B). NOTE 1—These tests are based on the fact that slates containing calcium carbonate undergo a chemical weathering which produces gypsum and carbon dioxide. The swelling action that results causes disintegration of the slate. Oxidation of iron sulfides (such as pyrite) may also adversely affect weathering durability of a slate. The extent of such action on various slates in the test has been found to correlate with the durability of the materials in actual weathering. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Weather Resistance of Slate

ASTM C216-22 饰面砖（粘土或页岩制实心砌块）标准规范

1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining compliance with the requirements of this specification is beyond the intent of this standard. 1.3 The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C902). 1.4 Brick are ceramic products manufactured primarily from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). Additives or recycled materials are permitted to be included at the option of the manufacturer. The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see Terminology C1232). 1.5 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5.1 This standard and its individual requirements shall not be used to qualify or corroborate the performance of a masonry unit made from other materials, or made with other forming methods, or other means of binding the materials. 1.6 Three types of brick in each of two grades are covered. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C652-22 空心砖（粘土或页岩制空心砌块）标准规范

1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion; intended for use in masonry supplying structural and/or facing components to the structure. In this specification, the term hollow brick shall be understood to mean hollow clay masonry units whose net cross-sectional area (solid area) in any plane parallel to the surface containing the cores, cells, or deep frogs, is less than 75 % of its gross cross-sectional area measured in the same plane (see 4.3). 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining compliance with the requirements of this specification is beyond the intent of this standard. 1.3 This specification does not cover brick intended for use as paving brick (see Specification C902). 1.4 Brick covered by this specification are ceramic products manufactured primarily from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. Additives or recycled materials are permitted to be included at the option of the manufacturer. (See “firing” and “firing bond” in Terminology C1232.) 1.4.1 This specification and its individual requirements shall not be used to qualify or corroborate the performance of a masonry unit made from other materials, or made with other forming methods, or other means of binding the materials. 1.5 Four types of hollow brick in each of two grades and two classes are covered. 1.6 Hollow brick differ from unglazed structural clay tile (Specifications C34 and C212) and solid brick (Specifications C62 and C216). Hollow brick require greater shell and web thicknesses and higher minimum compressive strength than structural clay tile, but permit greater void area and lesser distance from exposed edge to core hole than solid brick. Therefore, environmental and structural performance may be different in elements constructed of hollow brick from those constructed of structural clay tile or solid brick. 1.7 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

ASTM C1799/C1799M-22 尺寸石材试样取样和制备的标准指南

Standard Guide to Dimension Stone Test Specimen Sampling and Preparation

ASTM C1799/C1799M-22e1 石料试样取样和制备尺寸的标准指南

1.1 This guide covers sampling, selection, preparation, and conditioning of specimens that will be used to test material properties of dimension stone. 1.2 This guide sets forth basic recommendations for sampling and preparation of dimension stone test specimens and provides information regarding variables that should be considered. 1.3 This guide is intended to be used by architects, engineers, contractors and material suppliers who design, select, specify, install, purchase, fabricate, finish, or test natural stone products for construction applications. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide to Dimension Stone Test Specimen Sampling and Preparation

GSO ASTM C1405:2022 釉面砖（单烧砖块）的标准规范

This specification deals with the standards for bricks, having a ceramic glaze finish fused to the body during the same process as the unit body firing, that are intended for use in masonry. These products are also proposed for use in supplying structural or facing components. This specification, however, doest not cover double-fired glazed brick. The bricks shall be available in two grades: grade S (standard) and grade SS (select sized). Two types and classes of bricks are also covered: type I (single-faced units) and type II (two-faced units); and class exterior and class interior. The glazed bricks shall also conform to the physical properties such as durability, strength and absorption requirements and freezing and thawing requirements.

Standard Specification for Glazed Brick (Single Fired, Brick Units)

T/SDGSY 6-2022 机制砂颗粒球型度漏斗法试验规程

4技术要求 4.1机制砂球型度规格等级 机制砂颗粒球型度规格等级可分为三级，分别为QⅠ级、QⅡ级和QⅢ级。 4.2机制砂球型度技术要求 机制砂球型度技术要求应符合表4.2要求。 表4.2 机制砂球型度技术要求 机制砂球型度规格等级　机制砂试样的球型度指数γ（%） QⅠ　≤120 QⅡ　120～130 QⅢ　≥130

Specification for sphericity of manufactured sand with funnel test

BS EN 1097-6:2022 骨料的机械和物理性能测试 颗粒密度和吸水率的测定

What is BS EN 1097-6 - Particle density and water absorption of normal weight and lightweight aggregates about?    BS EN 1097 discusses tests for mechanical and physical properties of aggregates. BS EN 1097-6 is the sixth part of the BS EN 1097 multi-series.   BS EN 1097-6 specifies the reference methods used for type testing and in case of dispute, for the determination of particle density and water absorption of normal weight and lightweight aggregates.   Who is BS EN 1097-6- Particle density and water absorption of normal weight and lightweight aggregates for?   BS EN 1097-6 on the particle density and water absorption of normal weight and lightweight aggregates is useful for:  

Tests for mechanical and physical properties of aggregates. Determination of particle density and water absorption

BS EN 933-9:2022 骨料几何特性的测试 罚款评估 亚甲蓝测试

What is BS EN 933-9 - Methylene blue about?    BS EN 933 discusses tests for geometrical properties of aggregates. BS EN 933-9 is the ninth part of the BS EN 933 multi-series and discusses the methylene blue test.   BS EN 933-9 specifies the reference method used for type testing and in cases of dispute, for the   determination of the methylene blue value of the size 0/2 mm fraction in fine aggregates or all-in aggregates (MBf).   Who is BS EN 933-9- Methylene blue for?   BS EN 933-9 on the determination of the methylene blue value of the size 0/2 mm fraction in fine aggregates or all-in aggregates (MBf) is use...

Tests for geometrical properties of aggregates. Assessment of fines. Methylene blue test

T/CFA 0202032-2022 粘结剂喷射铸型（芯）用硅砂

本文件规定了粘结剂喷射铸型（芯）用硅砂的术语和定义、性能要求、试验方法、检验规则、包装、标志、运输和贮存。

Silica sand for binder jetting sand mould（core）