91.100.60 隔声和绝热材料 标准查询与下载

ASTM E2988-17(2022) 评估表面燃烧特性的金属建筑物用柔性纤维玻璃隔热材料的样品制备和安装

1.1 This practice describes a procedure for specimen preparation and mounting when testing Flexible Fibrous Glass Insulation for Metal Buildings to assess flame spread and smoke development as surface burning characteristics using Test Method E84. 1.2 This practice applies to products described in Specification C991. 1.3 This practice provides instructions for the testing of both un-faced insulation (Specification C991 Type I) and face insulation (Specification C991 Type II). 1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.5 Use the values stated in inch-pound units as the standard in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details. 1.6 This fire standard cannot be used to provide quantitative measures. 1.7 Fire testing of products and materials is inherently hazardous and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials, operations and equipment. 1.8 This practice gives instructions on specimen preparation and mounting but the fire-test-response method shall be conducted in accordance with Test Method E84. See also Section 8 for information on operator safety. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics

ASTM C1534-22 用作管道系统热和吸音衬垫的柔性聚合物泡沫板绝缘材料的标准规范

1.1 This specification covers the composition, dimensions, and physical properties of flexible unfaced foam sheet, used to insulate interior surfaces of HVAC ducts, plenums and equipment used for the distribution of conditioned air with a temperature of up to 250°F (121°C). 1.2 HVAC ducts, plenums and equipment systems typically operate between a temperature range of 50°F to 150°F (10°C to 65°C) and are designed to meet building code requirements of maximum temperatures of 250°F (121°C). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems

ASTM C167-22 毯子或板条隔热层厚度和密度的标准试验方法

1.1 These test methods cover the determination of thickness and density of flexible, felted, or woven thermal insulating blankets, rolls, or batts composed of fibrous materials, with or without surface covering or reinforcement. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations

ASTM C1224-22 建筑用反射绝缘标准规范

1.1 This specification covers the general requirements and physical properties of reflective insulations for use in building applications. These insulation materials consist of one or more low emittance surfaces, such as metallic foil or metallic deposits, unmounted or mounted on substrates. Reflective insulations derive thermal performance from surfaces with an emittance of 0.1 or less, facing enclosed air spaces. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Reflective Insulation for Building Applications

BS EN ISO 12629:2022 用于建筑设备和工业装置的隔热产品 预制管道保温材料水蒸气透过性能的测定

1   Scope This document specifies the equipment and procedure for determining the water vapour transmission properties in the steady state under specified test conditions for test specimens of preformed pipe insulation. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials (see NOTE below) and for products which can have integral skins or adhered facings of some different material. NOTE A material is considered to be homogeneous in terms of mass distribution if its density is approximately the same throughout, i.e. if the measured density values are close to its mean density.

Thermal insulating products for building equipment and industrial installations. Determination of water vapour transmission properties of preformed pipe insulation

BS EN ISO 12623:2022 用于建筑设备和工业装置的隔热产品 通过部分浸没预制管道保温材料来测定短期吸水率

1   Scope This document specifies the equipment and procedures for determining the short-term water absorption of preformed pipe insulation by partial immersion in water. It is applicable to thermal insulating products. NOTE It is intended to simulate the water absorption caused by exposure to rain for 24 h during product installation. This document has been prepared for products used to insulate building equipment and industrial installations, but it can also be applied to products used in other areas.

Thermal insulating products for building equipment and industrial installations. Determination of short-term water absorption by partial immersion of preformed pipe insulation

T/JCJJ 003-2022 《现浇混凝土复合外保温（岩棉）免拆模板建筑构造》图集

“现浇混凝土复合外保温(岩棉)模板”产品作为A级耐火保温材料用于建筑保温与结构一体化体系中，可有效解决节能保温工程质量通病和消防安全，符合国家节能减排发展方向和产业政策。该技术对于提高建筑节能水平、促进建设领域转型升级具有重要意义。 本次编制新疆地区《现浇混凝土复合外保温(岩棉)模板建筑构造》的指导思想，是立足于现行国家标准、规范以及国家和自治区鼓励和技术要求，结合新疆的地域特点、经济能力、施工水平，为下一步岩棉板应用于建筑市场开辟了一个新领域，并可以充分发挥岩棉板性能稳定，A级防火等优点，采用国内外先进的保温工程施工方法，提出现浇混凝土复合外保温(岩棉)模板体系，为新疆外墙外保温的保温施工一体化技术提供新产品，达到建筑节能和延长建筑物工程寿命的目的。

Atlas of "Cast-in-place Concrete Composite External Insulation (Rock Wool) Free Formwork Construction"

ISO 29469:2022 建筑用隔热产品.压缩性能的测定

This document specifies the equipment and procedures for determining the compression behaviour of specimens . It is applicable to thermal insulating products and can be used to determine the compressive stress in compressive creep tes ts and for applications in which insulation products are exposed only to short-term loads . The method can be used for quality control purposes and can also be employed to obtain reference values from which design values can be calculated using safety factors.

Thermal insulating products for building applications — Determination of compression behaviour

ISO 29466:2022 建筑用隔热产品.厚度的测定

This document specifies the equipment and procedures for determining the thickness of full-size products. It is applicable to thermal insulating products. This document provides the reference method. Other methods can be used (e.g. for quality control), provided a correlation has been established with this reference method; Annex B gives some examples of such methods.

Thermal insulating products for building applications — Determination of thickness

ASTM D7877-22 防水膜泄漏检测和定位的电子方法标准指南

1.1 This guide describes standard procedures for using electrical conductance measurement methods to locate leaks in exposed or covered waterproof membranes. 1.2 This guide addresses the need for a general technical description of the current methods and procedures that are used to test and verify the integrity of waterproof membranes. 1.3 This guide is not intended to replace visual, infrared, or other methods of inspection. It is to be used in conjunction with other methods of roof inspection when specified. 1.4 This guide recommends that the leak location equipment, procedures, and survey parameters used are calibrated to meet established minimum leak detection sensitivity. The leak detection sensitivity calibration should be verified on a regular basis according to the manufacturer’s recommendations. 1.5 Leak location surveys can be used on waterproofing membranes installed in roofs, plaza decks, pools, water features, covered reservoirs, and other waterproofing applications. 1.6 The procedures are applicable for membranes made of materials such as polyethylene, polypropylene, polyvinyl chloride, bituminous material, and other electrically insulating materials. 1.7 This guide provides a general description of the equipment and methods for locating membrane breaches using electric conductance. Refer to the manufacturer’s instructions for the proper operation and use of the equipment described in this guide. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Electronic Methods for Detecting and Locating Leaks in Waterproof Membranes

T/CBCA 013-2022 被动式超低能耗建筑材料 第一部分： 保温系统材料

本文件规定了被动式超低能耗建筑用保温系统材料的术语和定义、一般规定、技术要求、试验方法、检验规则、包装、运输与贮存。

Passive ultra-low energy consumption building materials-part 1: materials for thermal insulation systems

ASTM C1728-22 柔性气凝胶绝缘标准规范

1.1 This specification covers the classification and performance of flexible aerogel thermal insulation. This will cover the range of continuous exposure operating temperatures from –321°F (–196°C) up to 1200°F (649°C). 1.2 For satisfactory performance, properly installed protective vapor retarders or barriers shall be used on below ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor retarder or barrier could lead to insulation and system non-performance. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Flexible Aerogel Insulation

BS EN ISO 18097:2022 用于建筑设备和工业装置的隔热产品 最高使用温度的测定

This document specifies the equipment and procedures for determining the maximum service temperature of flat insulation products. It is applicable to thermal insulating products.

Thermal insulating products for building equipment and industrial installations. Determination of maximum service temperature

BS EN ISO 29770:2022 用于建筑应用的隔热产品 浮动地板绝缘产品厚度的测定

1   Scope This document specifies the equipment and procedures for determining the thickness of thermal insulating products for impact sound insulation in floating-floor applications.

Thermal insulating products for building applications. Determination of thickness for floating-floor insulating products

BS EN ISO 18099:2022 用于建筑设备和工业装置的隔热产品 热膨胀系数的测定

1   Scope This document specifies the equipment and procedures for determining the coefficient of linear thermal expansion . It is applicable to thermal insulating products within the temperature range −196 °C to 850 °C, subject to the possible temperature limitation of the test specimens. It is not applicable to products which experience dimensional changes during the test due to the loss of hydration water or which undergo other phase changes.

Thermal insulating products for building equipment and industrial installations. Determination of the coefficient of thermal expansion

BS EN ISO 18098:2022 用于建筑设备和工业装置的隔热产品 预制保温管表观密度的测定

1   Scope This document specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. It is applicable to full-size thermal insulating products and test specimens of preformed pipe insulation.

Thermal insulating products for building equipment and industrial installations. Determination of the apparent density of preformed pipe insulation

BS EN ISO 12624:2022 用于建筑设备和工业装置的隔热产品 痕量水溶性氯化物、氟化物、硅酸盐、钠离子和pH值的测定

1   Scope This document specifies the equipment and procedures for determining trace quantities of the water-soluble chloride, fluoride, silicate and sodium ions in an aqueous extract of the product. It also describes a procedure for the determination of the pH of the aqueous extract. It is applicable to thermal insulating products. NOTE The determination of these parameters can be relevant for thermal insulating products intended for application to stainless austenitic steel surfaces. The presence of chloride, fluoride, silicate and sodium ions under certain conditions can influence the risk of stress corrosion cracking. See Annex B for further information on general use of this document.

Thermal insulating products for building equipment and industrial installations. Determination of trace quantities of water-soluble chloride, fluoride, silicate, sodium ions and pH

BS EN ISO 29468:2022 用于建筑应用的隔热产品 平整度的测定

1   Scope This document specifies the equipment and procedures for determining the deviation from flatness for full-size products. It is applicable to thermal insulating products.

Thermal insulating products for building applications. Determination of flatness

BS EN ISO 29768:2022 用于建筑应用的隔热产品 试样线性尺寸的测定

1   Scope This document specifies the characteristics and choice of measuring equipment and the procedure for determining the linear dimensions of test specimens that are taken from thermal insulating products. The procedures for measuring the dimensions of full-size products are specified in ISO 29465 and ISO 29466.

Thermal insulating products for building applications. Determination of linear dimensions of test specimens

BS EN ISO 18096:2022 用于建筑设备和工业装置的隔热产品 预制管道保温最高使用温度的确定

1   Scope This document specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products.

Thermal insulating products for building equipment and industrial installations. Determination of maximum service temperature for preformed pipe insulation