91.140.10 中央供热系统 标准查询与下载

DB45/T 1971-2019 室内装饰装修主要材料有害物质限量

Limits of hazardous substances in main materials for interior decoration

T/CECS 614-2019 村镇建筑清洁供暖技术规程

本规程共分10章和3个附录，主要技术内容包括：总则、术语、基本规定、建筑节能设计、太阳能供暖、生物质能供暖、空气源热泵供暖、地热能供暖、燃气供暖、电热供暖等。

Clean heating technology regulations for village and town buildings

ASTM E2618-13(2019) 固体燃料热水加热设备的颗粒物排放和加热效率测量的标准测试方法

1.1 This test method applies to wood-fired or automatically fed biomass burning hydronic heating appliances. These appliances transfer heat to the indoor environment through circulation of a liquid heat exchange media such as water or a water-antifreeze mixture. 1.2 The test method simulates hand loading of seasoned cordwood or fueling with a specified biomass fuel and measures particulate emissions and delivered heating efficiency at specified heat output rates based on the appliance’s rated heating capacity. 1.3 Particulate emissions are measured by the dilution tunnel method as specified in Test Method E2515. Delivered efficiency is determined by measurement of the usable heat output (determined through measurement of the flow rate and temperature change of water circulated through a heat exchanger external to the appliance) and the heat input (determined from the mass of dry fuel burned and its higher heating value). Delivered efficiency does not attempt to account for pipeline loss. 1.4 Products covered by this test method include both pressurized and non-pressurized heating appliances intended to be fired with wood or automatically fed biomass fuels. These products are hydronic heating appliances which the manufacturer specifies for outdoor or indoor installation. They are often connected to a heat exchanger by insulated pipes and normally include a pump to circulate heated liquid. They are used to heat structures such as homes, barns, and greenhouses and can heat domestic hot water, spas, or swimming pools. 1.4.1 Hydronic heating systems that incorporate a high mass heat storage system that is capable of storing the entire heat output of a standard fuel load are tested by the procedure specified in Annex A1. Systems that incorporate high mass heat storage capable of storing a portion of the output from a standard fuel load are tested by the procedure specified in Annex A2. 1.5 Distinguishing features of products covered by this standard include: 1.5.1 Manufacturers specify indoor or outdoor installation. 1.5.2 A firebox with an access door for hand loading of fuel or a hopper and automated feed system for delivery of particulate fuel such as wood pellets or solid biomass fuel to a burn pot or combustion chamber. 1.5.3 Typically a thermostatic control device that controls combustion air supply or fuel delivery, or both, to maintain the liquid in the appliance within a predetermined temperature range provided sufficient fuel is available in the firebox or hopper. 1.5.4 A chimney or vent that exhausts combustion products from the appliance. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6.1 Exception—Metric units are used in 13.1, 13.4.3, Tables 4-6, and A1.11.6. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.54 on Solid Fuel Burning Appliances. Current edition approved July 1, 2019. Published July 2019. Originally approved in 2008. Last previous edition approved in 2013 as E2618–13. DOI: 10.1520/ E2618–13R19. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel-Fired Hydronic Heating Appliances

IEC 60335-2-51:2019 家用和类似用途电器.安全.第2-51部分:供暖和工业用水装置用固定循环泵的特殊要求

Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations

IEC 60335-2-51:2019 RLV 家用和类似用途电器.安全.第2-51部分:供暖和工业用水装置用固定循环泵的特殊要求

Household and similar electrical appliances - Safety - Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations

T/CECS 10008-2018 《供暖器具及供暖系统用 钎焊板式换热器》

本标准规定了供暖器具及供暖系统用钎焊板式换热器（以下简称“换热器”）的术语和定义，分类和型号，材料、结构和外观，性能要求,试验方法，检验规则，标志、包装、运输和贮存。

Brazed plate heat exchanger for heating appliance and heating system

CJ/T 25-2018 供热用手动流量调节阀

　　现批准《供热用手动流量调节阀》为城镇建设行业产品标准，编号为CJ/T25-2018，自2019年5月1日起实施。原《供热用手动流量调节阀》（CJ/T25-1999）同时废止。 　　本标准在住房城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房城乡建设部标准定额研究所组织中国标准出版社出版发行。 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2018年11月16日

Manual flow control valve for heating

CJ/T 179-2018 自力式流量控制阀

　　现批准《自力式流量控制阀》为城镇建设行业产品标准，编号为CJ/T179-2018，自2019年5月1日起实施。原《自力式流量控制阀》（CJ/T179-2003）同时废止。 　　本标准在住房城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房城乡建设部标准定额研究所组织中国标准出版社出版发行。 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2018年11月16日

Self operated flow control valve

JIS A 4008:2018 风机盘管

Fancoil units

DIN SPEC 12831-1:2018 房间热负荷的计算方法 第1部分：国家对 DIN EN 12831-1 的补充

The basic calculation of the heat load of a room, a utilization or building unit (e. g. apartment) as well as a building is described in DIN EN 12831-1:2017. The present document is a national supplement to DIN EN 12831-1 and applies to its application - usually by defining input variables or defining calculation parameters - in accordance with DIN EN 12831-1:2017 Annex A. The hydraulic and control engineering design of plant components are not the subject of DIN EN 12831-1:2017 and this document.

Method for calculation of the room heat load - Part 1: National addition to DIN EN 12831-1, with CD-ROM

CJ/T 246-2018 城镇供热预制直埋蒸汽保温管及管路附件

Urban heating prefabricated directly buried steam insulation pipes and piping accessories

DIN SPEC 15378:2018 锅炉、供暖系统和 DHW 的检查 DIN EN 15378-1:2017-09 的国家补充

This document describes the in Germany applicable procedures for the one-time and recurring inspection of heating systems. This document is valid in conjunction with DIN EN 15378-1 and specifies the extent and periodicity of the energy inspections of heat generators and heaters as covered by the EPBD. For the purposes of this document, the term "inspection" shall mean the qualitative and / or quantitative recording and assessment of the energy efficiency of the heating installation or its components with the aim of deriving measures for maintaining or improving the energy quality of the heating installations or these components. The inspection as part of the measures for the maintenance of a heating system or its components, (inspection, maintenance and repair) is not covered by this document. The specifications of this standard do not replace the design of a heating system or its components. This document applies to all heating systems in residential and non-residential buildings with a nominal heat output of 4 kW. As authorized in DIN EN 15378-1, such national specifications may be described in national publications, which may be referred to in the national annex of DIN EN 15378-1.

Inspection of boilers, heating systems and DHW - National addition to DIN EN 15378-1:2017-09

EN 16510-1:2018 家用固体燃料燃烧器具 第1部分：一般要求和测试方法

Residential solid fuel burning appliances - Part 1: General requirements and test methods

JG/T 2-2018 钢制板型散热器

本标准规定了钢制板型散热器(以下简称“散热器”)的分类与标记、材料与结构、要求、试验方法、检验规则、标志、使用说明书及合格证、包装、运输和贮存。 本标准适用于工业与民用建筑供暖系统，以温度不高于95 ℃且水质符合GB/T 29044-2012中4.5规定的热水为热媒的散热器。

Steel panel radiator

CJ/T 515-2018 燃气锅炉烟气冷凝热能回收装置

　　现批准《燃气锅炉烟气冷凝热能回收装置》为城镇建设行业产品标准，编号为CJ/T515-2018，自2018年12月1日起实施。 　　本标准在住房城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房城乡建设部标准定额研究所组织中国标准出版社出版发行。 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　2018年5月30日

Gas boiler flue gas condensation heat energy recovery device

JG/T 143-2018 铝制柱翼型散热器

Aluminum column airfoil radiator

BS EN 304:2017 供暖锅炉 雾化油燃烧器加热锅炉试验规范

Heating boilers. Test code for heating boilers for atomizing oil burners

EN 304:2017 供暖锅炉.雾化喷油嘴用供暖锅炉的试验规程

This European Standard applies to the determination of the performances of heating boilers and combi boilers fired by liquid fuels. The requirements for the heating performances are laid down in EN 303 1:2016 and EN 303 2:2016. This test code includes the requirements and recommendations for carrying out and evaluating the procedure for testing boilers and also the details of the technical conditions under which the tests will be carried out. The requirements and the performance of testing for the sanitary hot water production of combi boilers are laid down in EN 303 6.

Heating boilers - Test code for heating boilers for atomizing oil burners

DIN EN 303-1:2017 采暖锅炉.第1部分:带强制通风燃烧器的采暖锅炉.术语、一般要求、检验和标记;德文版本EN 303-1-2017

This European Standard applies to boilers used for central heating (heating boilers) with forced draught burners with a nominal heat output not exceeding 1000 kW, which are operated either with negative pressure (natural draught boilers) or with positive pressure (pressurized boiler) in the combustion chamber, in accordance with the boiler manufacturers instruction. This standard specifies the necessary terminology, the requirements on the materials and testing of them, and marking requirements for heating boilers. Particular requirements for boilers that can be used with open vented systems are contained in EN 3034. The requirements of this standard apply to heating boilers that are tested on an authorized test rig. Boilers in accordance with this standard are designed for the heating of central heating installations in which the heat carrier is water, and the maximum allowable operating temperature of which is restricted to 100 °C. The maximum allowable operating pressure is 8 bar. For boilers (storage or continuous flow heater) this standard only applies to the parts of the water heater that are necessarily subject to the operating conditions of the heating boiler (heating part). This standard does not apply to gas boilers with atmospheric burners, boilers for solid fuels, boilers and boilers with oil vaporization burners. For these boilers there are further requirements.

Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking; German version EN 303-1:2017

DIN EN 303-2:2017 采暖锅炉.第2部分:带强制通风燃烧器的采暖锅炉.带雾化油燃烧器的采暖锅炉的特殊要求;德文版本EN 303-2-2017

This European Standard is applicable to boilers used for central heating in accordance with EN 303-1:2017 up to a nominal heat output of 1000 kW and EN 303-4 up to a nominal heat output of 70 kW with forced draught burners in accordance with EN 267 that are designed for operating with liquid fuels. The performance requirements of this standard apply to type testing to heating boilers (standard, low temperature and condensing boilers) which are tested on a test rig in accordance with the test code given in EN 304. This standard applies also to room sealed boilers as defined in EN 15035 regarding efficiency and emissions. This standard can also be used as the basis for evaluation of boiler-/burner units.

Heating boilers - Part 2: Heating boilers with forced draught burners - Special requirements for boilers with atomizing oil burners; German version EN 303-2:2017