97.100.99 使用其他能源的加热器 标准查询与下载

GB/T 23137-2020 家用和类似用途热泵热水器

本标准规定了家用和类似用途热泵热水器(以下简称热泵热水器)的术语和定义.产品分类、技术要求.试验方法.检验规则标志、包装.运输,贮存等。本标准适用于电动机驱动,采用蒸气压缩制冷循环,以空气或水作为热源,以提供热水为目的的家用和类似用途的热泵热水器。其他热源或用途的热泵热水器可参照使用。本标准不适用于工业用热泵热水器。

Heat pump water heater for household and similar application

GB/T 38734-2020 以CO2为制冷剂的热泵热水器技术要求和试验方法

本标准规定了以二氧化碳(CO; )为制冷剂的热泵热水需(以下简称热泵热水器)的术语和定义、产品分类 .技术要求及试验方法。 本标准适用于电动机驱动 ,使用二氧化碳(CO，* )作制冷剂 ,采用蜂临界压缩循环,以空气作为热源，额定制热量不超过 16 000 到,以提供热水为目的的家用和类似用途的热泵热水需。 本标准不适用于工业用热泵热水器。

Technical requirements and test methods for household and similar heat pump water heaters with CO2 as refrigerants

T/QGCML 3259-2024 电热执行器

本文件规定了电热执行器的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于安装在DN50及以下的小口径电动阀、分集水器支路、平衡阀和散热器恒温控制阀上的直流电压不超过50 V，交流电压不超过250 V的电热执行器的设计、生产和检验。

electrothermal actuator

T/QGCML 3209-2024 小型家用箱式取暖器生产技术规范

本文件规定了小型家用箱式取暖器的术语和定义、型号参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存相关内容。 本文件适用于小型家用箱式取暖器的生产、检验。

Technical specifications for production of small household box heaters

23/30464837 DC BS EN 16647-1 酒精驱动的无烟道壁炉 安全要求和测试方法 第 1 部分：家用手动装饰壁炉

BS EN 16647-1. Alcohol powered flueless fireplaces. Safety requirements and test methods - Part 1. Manually operated decorative fireplaces for domestic use

QB/T 5788-2022 电热执行器

Electrothermal actuator

QB/T 5689-2022 家用和类似用途热泵热水器用微通道冷凝器

Microchannel condensers for heat pump water heaters for domestic and similar purposes

T/CAQI 200-2021 小型清洁生物质采暖炉具

外观要求、材料要求、尺寸要求、焊接要求、热性能指标、烟气污染物排放指标、安全使用要求。

Small-scale clean biomass heating stoves

T/GDAR 0002-2020 家用和类似用途空气源热泵热水器

本标准规定了用于制取生活热水用的空气源热泵热水器（以下简称：热水器）的术语和定义、要求和试验。 本标准适用于自带储水箱、额定制热量≤12kW、水箱容量≤600L的家用和类似用途空气源热泵热水器。本标准不适用于以下类型的空气源热泵热水器： ——商业和工业用途空气源热泵热水器； ——采暖用途的低环境温度空气源热泵热水机组； ——多用途的空气源热泵热水器。

Air-source heat pump water heater for household and similar application

20/30409057 DC BS EN 16647 AMD1 液体燃料壁炉 使用酒精基燃料或凝胶状燃料产生火焰的装饰器具 在私人家庭中使用

BS EN 16647 AMD1. Fireplaces for liquid fuels. Decorative appliances producing a flame using alcohol based or gelatinous fuel. Use in private households

ASTM F3363-19 无气味液体/凝胶燃料燃烧便携式设备的标准规范

1.1 These requirements apply to devices that: 1.1.1 Sustain a flame over the fuel surface in an open reservoir; 1.1.2 Sustain a flame that does not require external ventilation to remove the combustion emissions, and are therefore ventless; 1.1.3 Burn a liquid, gelled, or otherwise non-solid fuel in an open reservoir or from a disposable, non-refillable, fuel container; 1.1.4 Have a fuel capacity of 2.5 L (0.67 gal) or less; 1.1.5 Have a power output of 1.47 kW (5000 BTU/h) or less; 1.1.6 Are intended to be easily carried or moved by hand; and 1.1.7 Are intended for indoor use, outdoor use, or both. 1.2 These requirements do not apply to devices that: 1.2.1 Are candles; 1.2.2 Are intended to cook or warm food; 1.2.3 Burn solid fuels, as determined by the test method described in Test Methods D4359; or 1.2.4 Do not have an open reservoir such as a refillable oil lamp, outdoor garden, or table torch intended to burn combustible fuel using a wick to sustain the flame (see Appendix X1). 1.3 This specification prescribes minimum safety requirements for devices to help ensure a reasonable degree of safety for normal use, thereby improving personal safety and reducing fires, deaths, and injuries. 1.4 This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.5 The values stated in SI units are to be considered standard. The values in parentheses are explanatory or approximate information. 1.6 This specification is used to measure and describe the response of materials, products, or assemblies to heat, flame, and forces under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Unvented Liquid/Gel Fuel-Burning Portable Devices

BS EN 16647:2015 液态燃料壁炉. 使用醇基或胶状燃料生成火焰的装饰性器具. 私人家庭使用

Fireplaces for liquid fuels. Decorative appliances producing a flame using alcohol based or gelatinous fuel. Use in private households

CAN/ULC-S674-2015(R2021) 无排气酒精燃料燃烧装饰器具标准

1.1 These requirements apply to Factory-Built Unvented Decorative Appliances that are intended to be fixed/non-movable and that use ethyl alcohol (ethanol) and isopropyl alcohol (isopropanol) in liquid or gel form as the fuel. These appliances are intended to be decorative in nature and limited to a maximum output of 3 kW (10,000 BTU/hour). Appliances that use fuel oils, kerosene, gasoline, and other non-alcohols are not covered by these requirements. NOTE: In Canada, the ethyl alcohol and isopropyl alcohol fuels for use with these products are to meet the Health Canada Consumer Chemicals and Containers Regulations 2001. 1.2 These appliances consist of an overall enclosure, burning chamber, and provision for refueling. They are not intended for use in spaces in which flammable vapours or gases may be present. They are not intended to be used as cooking or heating appliances. These appliances are not intended to be used in conjunction with blower assemblies. 1.3 These products are not intended to be installed in a bathroom or a room where sleeping accommodation is provided. 1.4 The appliances as covered by these requirements are intended for installation in accordance with local regulations and in the absence of such regulations in accordance with the current editions of the National Building Code of Canada and the National Fire Code of Canada.

Standard for Unvented Alcohol Fuel Burning Decorative Appliances

EN 16647:2015 壁炉的液体燃料.装饰电器使用酒精或凝胶状燃料产生火焰.私人使用

This European Standard applies for decorative fireplaces/appliances for domestic use, producing a flame using alcohol, hereafter referred to as fuel, in liquid or gelatinous fuel for decoration. NOTE 1 The requirements are strictly applied even when used in other areas. Outside the private household and outdoor area can apply more or different rules on the use of the appliances. This European Standard applies to free-standing, wall-mounted and built-in appliances with a maximum power output of 4,5 kW. This European Standard applies for appliances ready for use, whose burner is of one unit or are an integral component of the appliances but not for appliances with a fuel tank separate from the appliance. This European Standard does not apply for appliances specifically designed for heating food or keeping food warm (rechauds), as well as for appliances for use in boats, caravans, other vehicles or outdoor areas. This European Standard does not apply for appliances with a power output higher than 4,5 kW or with a defined heating function. NOTE 2 National regulation may restrict the power output to less than 4,5 kW.

Fireplaces for liquid fuels - Decorative appliances producing a flame using alcohol based or gelatinous fuel - Use in private households

ANSI/UL 1370-2014 未放气酒精燃料作为燃料的装饰性灶具用安全性标准

Standard for Safety for Unvented Alcohol Fuel Burning Decorative Appliances

ANSI/UL 1370a-2014 未放气酒精燃料作为燃料的装饰性灶具用安全性标准

Standard for Safety for Unvented Alcohol Fuel Burning Decorative Appliances

BS PAS 67:2013 测定主要用于住所采暖的热导微型热电联产组合装置的供暖和电气性能的实验室方法

Laboratory tests to determine the heating and electrical performance of heat-led micro-cogeneration packages primarily intended for heating dwellings

UL 1370-2011 燃烧酒精燃料的不排气装饰性加热器具

Unvented alcohol fuel burning decorative heating appliances

DIN 4734-1:2011 液体燃料壁炉.使用乙醇基或胶状燃料的产生火焰的装饰性电气用具.第1部分:用于私人家庭

Fireplaces for liquid fuels - Decorative appliances producing a flame using ethanol based or gelatinous fuel - Part 1: Use in private households

PAS 67-2008 主要用于住所采暖的热导微型热电联产组合装置的加热和电气性能测定的实验室试验

This Publicly Available Specification (PAS) specifies a comprehensive set of test conditions for determining the heating and electrical performance of heat-led micro-cogeneration packages that are primarily intended for use in dwellings. The PAS is suitable for testing those micro-cogeneration packages with a thermal output up to 70 kW (252 MJ/hr); the full output test may also be suitable for packages up to 400 kW (1440 MJ/hr). For the category of micro-cogeneration package that provides space and water heating in which the domestic hot water (DHW) is provided wholly from within the package (CombiPK), the DHW test conditions described in this PAS are only applicable for packages with less than 15 litres of water storage. For CombiPK packages with hot water storage of 15 litres or more, the DHW test has not been yet been developed and this will be considered for the next revision of the PAS. However, CombiPK packages with hot water storage of 15 litres or more can be tested using all other PAS 67 tests (full output, partial output and standby tests). The PAS results can be input to the procedure to calculate annual energy performance, such as “Method to evaluate the annual energy performance of micro-cogeneration heating systems in dwellings” [2] which for these products, until the PAS is revised, treats the DHW load as additional space heating load. This enables the estimation of the annual energy performance and derivation of the single index of performance for product comparison. A reporting format for the test results is also specified. NOTE PAS 67 is not intended to deliver an evaluation of the annual energy performance of a product directly, but provides the data from which it may be calculated. It is intended to produce test results and other information that can be used in a separate method of calculation of annual energy performance of the micro-cogeneration package. An estimate of annual energy performance is necessary for the SAP (The UK Government’s Standard Assessment Procedure for Energy Rating of Dwellings) [3] and other energy rating schemes. The document “Method to evaluate the annual energy performance of micro-cogeneration heating systems in dwellings” [2] specifies such a method. An extension of the annual energy performance method is used to derive a single index of performance for product comparison, similar in principle to SEDBUK (Seasonal Efficiency of Domestic Boilers in the UK) [4] already used for boilers.

Laboratory tests to determine the heating and electrical performance of heat-led micro-cogeneration packages primarily intended for heating dwellings