97.190 儿童用器具 标准查询与下载

ASTM F2012-18e1 固定活动中心的标准消费者安全绩效规范

1.1 This consumer safety performance specification covers performance requirements, test methods and marking requirements to promote safe use of a stationary activity center by an occupant. 1.2 This consumer safety performance specification is intended to minimize the risk of incidents to an occupant resulting from normal use and reasonably foreseeable misuse or abuse of a stationary activity center. 1.3 No stationary activity center produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 This consumer safety performance specification is not intended to address incidents and injuries resulting from the interaction of other persons with the child occupant in the stationary activity center or the incidents resulting from abuse and misuse by children able to walk. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Performance Specification for Stationary Activity Centers

ASTM F2388-18 家用婴儿更换产品的标准消费者安全规范

Standard Consumer Safety Specification for Baby Changing Products for Domestic Use

ASTM F406-17 非全尺寸婴儿床/游乐场的标准消费者安全规范

Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

ASTM F2388-17a 家用婴儿更换产品的标准消费者安全规范

Standard Consumer Safety Specification for Baby Changing Products for Domestic Use

ASTM F2167-17 婴儿保镖座椅的消费者安全标准规范

1.1 This consumer safety specification covers establishment of requirements, test methods, and marking requirements to promote safe use of an infant bouncer seat by an occupant and a caregiver. 1.2 For purposes of this consumer safety specification, an infant bouncer seat is a freestanding product intended to support an occupant in a reclined position to facilitate bouncing by the occupant, with the aid of a caregiver or by other means. Intended occupants are infants who have not developed the ability to sit up unassisted (approximately 0 to 6 months of age). 1.3 This consumer safety specification is intended to minimize the risk of injury to an occupant resulting from normal use and reasonably foreseeable misuse or abuse of an infant bouncer seat. 1.4 No infant bouncer seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons with the occupant in an infant bouncer seat or the incidents resulting from abuse or misuse by other children. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Specification for Infant Bouncer Seats

ASTM F2388-17 家用婴儿更换产品的标准消费者安全规范

1.1 This consumer safety specification covers performance requirements, test methods, and labeling requirements to promote the safe use of baby changing products including changing tables, changing table accessories, contoured changing pads, and add-on changing units. 1.2 This specification covers products sold for domestic use for children up to a weight of 30 lb (13.6 kg). 1.3 Changing products shall meet all applicable performance and labeling requirements. 1.4 No changing product produced after the approval date of this specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before, and after all testing. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test method portion in Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Specification for Baby Changing Products for Domestic Use

EN 1272:2017 儿童保育产品.装有椅子的桌子.安全要求和试验方法

Child care articles - Table mounted chairs - Safety requirements and test methods

DIN EN 12868:2017 儿童使用和保育用品.测定弹性体或橡胶奶头和安慰奶嘴中释放的N-亚硝胺和N-nitrosatable物质的方法;德文版本EN 12868-2017

Child use and care articles - Method for determining the release of N-nitrosamines and N-nitrosatable substances from elastomer or rubber teats and soothers; German version EN 12868:2017

BS EN 12868:2017 儿童使用和护理用品 弹性体或橡胶奶嘴和安抚奶嘴中 N-亚硝胺和 N-亚硝基物质释放量的测定方法

Child use and care articles. Method for determining the release of N-nitrosamines and N-nitrosatable substances from elastomer or rubber teats and soothers

ASTM F2670-17 婴儿浴缸的标准消费者安全规范

1.1 This consumer safety specification establishes performance requirements, test methods, and labeling requirements to promote the safe use of infant bath tubs. Specifically excluded from the scope of this standard are products commonly known as bath slings, typically made of fabric or mesh. 1.2 This consumer safety specification is intended to reduce the risk of death and minimize injury to infants resulting from use and reasonably foreseeable abuse of infant bath tubs. 1.3 No infant bath tub produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Infant Bath Tubs

EN 12868:2017 儿童使用和护理用品-测定弹性塑料或橡胶奶头和安慰奶嘴中释放的N-亚硝胺和N-亚硝基胺物质的方法

This European Standard specifies the method for determining N-nitrosamines and N-nitrosatable substances released from elastomer or rubber teats in contact with artificial saliva salt solution for testing compliance with Directive 93/11/EEC.

Child use and care articles - Method for determining the release of N-nitrosamines and N-nitrosatable substances from elastomer or rubber teats and soothers

ASTM F3118-17 婴儿倾斜睡眠产品标准消费者安全规范

1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to minimize the hazards to infants presented by infant inclined sleep products as identified in the introduction. 1.2 This consumer safety specification is intended to minimize the risk of injuries to infants resulting from normal use and reasonably foreseeable misuse or abuse of infant inclined sleep products. 1.3 This consumer safety performance specification covers a free standing product with an inclined sleep surface primarily intended and marketed to provide sleeping accommodations for an infant up to 5 months old or when the infant begins to roll over or pull up on sides, whichever comes first. It also covers a smaller product intended for newborns up to 3 months old or when newborn begins to wiggle out of position or turn over in the product or weighs more than 15 lb (6.8 kg), whichever comes first. It also covers infant and newborn inclined sleep product accessories, which are attached to, or supported by, another product with the same age or abilities, or both, as the free standing products. If the inclined sleep product can be converted into a product for which another ASTM standard consumer safety specification exists, the product shall meet the applicable requirements of that standard. For example, an inclined sleep product that can have the recline angle adjusted below 10° shall also comply with the applicable requirements of Consumer Safety Specification F2194. 1.4 No infant inclined sleep product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Consumer Safety Specification for Infant Inclined Sleep Products

ASTM F3118-17a 婴儿用倾斜睡眠产品的标准消费者安全规格

1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to minimize the hazards to infants presented by infant inclined sleep products as identified in the introduction. 1.2 This consumer safety specification is intended to minimize the risk of injuries to infants resulting from normal use and reasonably foreseeable misuse or abuse of infant inclined sleep products. 1.3 This consumer safety performance specification covers a free standing product with an inclined sleep surface primarily intended and marketed to provide sleeping accommodations for an infant up to 5 months old or when the infant begins to roll over or pull up on sides, whichever comes first. It also covers a smaller product intended for newborns up to 3 months old or when newborn begins to wiggle out of position or turn over in the product or weighs more than 15 lb (6.8 kg), whichever comes first. It also covers infant and newborn inclined sleep product accessories, which are attached to, or supported by, another product with the same age or abilities, or both, as the free standing products. If the inclined sleep product can be converted into a product for which another ASTM standard consumer safety specification exists, the product shall meet the applicable requirements of that standard. For example, an inclined sleep product that can have the recline angle adjusted below 10° shall also comply with the applicable requirements of Consumer Safety Specification F2194. 1.4 No infant inclined sleep product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Specification for Infant Inclined Sleep Products

ASTM F1004-16a 扩展门和可扩展外壳的标准消费者安全规范

Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures

DIN EN 13209-2:2016 儿童使用和保育用品.童车.安全性和检验方法.第2部分:柔软的童车.德文版本EN 13209-2-2015

Child use and care articles - Baby carriers - Safety and test methods - Part 2: Soft carrier; German version EN 13209-2:2015

BS EN 13209-2:2015 儿童使用和保育用品.婴儿运载工具.安全要求和检验方法.软式运载工具

Child use and care articles. Baby carriers. Safety requirements and test methods. Soft carrier

KS G 3318-2016 涟漪装置

Rippling apparatus

ASTM F2194-16e1 摇篮和摇篮车的标准消费者安全规格

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of bassinets and cradles. 1.2 This consumer safety performance specification is intended to minimize the risks of incidents to an infant resulting from normal use and reasonably foreseeable misuse of a bassinet or cradle. 1.3 This consumer safety performance specification covers products primarily intended to provide sleeping accommodations for an infant up to approximately 5 months in age or when the child begins to push up on hands and knees, whichever comes first. Products used in conjunction with an inclined infant swing or stroller, or products that are intended to provide an inclined sleep surface (head-to-toe direction) of greater than 10° from horizontal while in the rest (non-rocking) position are not covered by this specification. 1.3.1 Rationale—The addition of developmental criteria was added to the 5-month age grade to accommodate varying motor skills in children. Note 1: Cradle swings with an incline less than or equal to 10° from horizontal while in the rest (non-rocking) position are covered under the scope of this standard. A sleep product that only has inclined sleeping surfaces (intended to be greater than 10° from horizontal while in the rest (non-rocking) position) does not fall under the scope of this standard. If a product can be converted to a bassinet/cradle use mode and meets the definition of a bassinet/cradle found in 3.1.1 while in that mode, the product shall be included in the scope of this standard, when it is in the bassinet/cradle use mode. For example, strollers that have a carriage/bassinet feature are covered by the stroller/carriage standard when in the stroller use mode. Carriage baskets/bassinets that are removable from the stroller base are covered under the scope of this standard when the carriage basket/bassinet meets the definition of a bassinet/cradle found in 3.1.1. Bassinet/cradle attachments to cribs or play yards, as defined in 3.1.2 or 3.1.13, are included in the scope of the standard when in the bassinet/cradle use mode. 1.4 No bassinet or cradle produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care giver. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Consumer Safety Specification for Bassinets and Cradles

ASTM F2194-16 摇篮和摇篮车的标准消费者安全规格

1.1 This consumer safety specification covers performance requirements, test methods, and marking requirements to promote safe use of bassinets and cradles. 1.2 This consumer safety performance specification is intended to minimize the risks of incidents to an infant resulting from normal use and reasonably foreseeable misuse of a bassinet or cradle. 1.3 This consumer safety performance specification covers products primarily intended to provide sleeping accommodations for an infant up to approximately 5 months in age or when the child begins to push up on hands and knees, whichever comes first. Products used in conjunction with an inclined infant swing or stroller, or products that are intended to provide an inclined sleep surface (head-to-toe direction) of greater than 10° from horizontal while in the rest (non-rocking) position are not covered by this specification. 1.3.1 Rationale—The addition of developmental criteria was added to the 5-month age grade to accommodate varying motor skills in children. Note 1: Cradle swings with an incline less than or equal to 10° from horizontal while in the rest (non-rocking) position are covered under the scope of this standard. A sleep product that only has inclined sleeping surfaces (intended to be greater than 10° from horizontal while in the rest (non-rocking) position) does not fall under the scope of this standard. If a product can be converted to a bassinet/cradle use mode and meets the definition of a bassinet/cradle found in 3.1.1 while in that mode, the product shall be included in the scope of this standard, when it is in the bassinet/cradle use mode. For example, strollers that have a carriage/bassinet feature are covered by the stroller/carriage standard when in the stroller use mode. Carriage baskets/bassinets that are removable from the stroller base are covered under the scope of this standard when the carriage basket/bassinet meets the definition of a bassinet/cradle found in 3.1.1. Bassinet/cradle attachments to cribs or play yards, as defined in 3.1.2 or 3.1.13, are included in the scope of the standard when in the bassinet/cradle use mode. 1.4 No bassinet or cradle produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 This consumer safety performance specification is not intended to address incidents and injuries resulting from alteration or unreasonable abuse or misuse of the product by a child or child care giver. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Consumer Safety Specification for Bassinets and Cradles

ASTM F2167-16 婴儿小弹椅的标准消费者安全规格

1.1 This consumer safety specification covers establishment of requirements, test methods, and marking requirements to promote safe use of an infant bouncer seat by an occupant and a caregiver. 1.2 For purposes of this consumer safety specification, an infant bouncer seat is a freestanding product intended to support an occupant in a reclined position to facilitate bouncing by the occupant, with the aid of a caregiver or by other means. Intended occupants are infants who have not developed the ability to sit up unassisted (approximately 0 to 6 months of age). 1.3 This consumer safety specification is intended to minimize the risk of injury to an occupant resulting from normal use and reasonably foreseeable misuse or abuse of an infant bouncer seat. 1.4 No infant bouncer seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein. 1.5 This consumer safety specification is not intended to address incidents and injuries resulting from the interaction of other persons with the occupant in an infant bouncer seat or the incidents resulting from abuse or misuse by other children. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following precautionary caveat pertains only to the test method portion, Section 7, of this consumer safety specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Consumer Safety Specification for Infant Bouncer Seats