B71 木材竹材防腐 标准查询与下载

DD 257-5-2003 木材防腐剂和经过防腐处理的木材的分析方法.用气相色谱法测定锌和铜羧酸盐中羧酸的类型

This part of DD 257 describes a method for the qualitative identification of carboxylic acids in wood preservative solutions containing zinc and copper carboxylates. It gives two gas chromatographic options: one using a capillary column and one using a packed column. It is applicable primarily to the analysis of preservative formulations conforming to BS 5707.

Methods of analysis of wood preservatives and treated timber. Determination of carboxylic acid type in zinc and copper carboxylate preservative solutions by gas chromatography

BS DD 257-3:2003 木材防腐剂和经过防腐处理的木材的分析方法.有机溶剂中木材防腐液中苄氯菊脂的定量分析

This part of DD 257 describes two methods (high performance liquid chromatography and gas chromatography) for the separation and determination of the cis and trans isomers of permethrin in organic solvent-based solutions of wood preservatives.

Methods of analysis of wood preservatives and treated timber. Quantitative analysis of permethrin in solutions of wood preservatives in organic solvents

BS DD 257-2:2003 木材防腐剂和经过防腐处理的木材的分析方法.含n丁锡化合物的木材防腐液和经过防腐处理的木材的定量分析.三丁锡、二丁锡和一丁锡含量的测定

This part of DD 257 describes two methods (polarographic and thin-layer chromatographic) for the determination of tributyltin, dibutyltin and monobutyltin compounds present in wood preservative solutions and in treated timber.

Methods of analysis of wood preservatives and treated timber. Quantitative analysis of wood preservative solutions and treated timber containing $in-butyltin compounds. Determination of tributyltin, dibutyltin and monobutyltin

BS DD 257-1:2003 木材防腐剂和经过防腐处理的木材的分析方法.含硼化物的木材防腐液和经过防腐处理过的木材的定量分析.硼总含量的测定

This part of DD 257 describes two methods ( titrimetric and colorimetric ) for the determination of boron compounds as boric acid in preservative solutions and in treated timber.

Methods of analysis of wood preservatives and treated timber. Quantitative analysis of wood preservative solutions and treated timber containing boron compounds. Determination of total boron

BS DD 257-5:2003 木材防腐剂与木材防腐处理的分析方法.用气相色谱法测定锌和铜羧酸盐中羧酸的类型

This part of DD 257 describes a method for the qualitative identification of carboxylic acids in wood preservative solutions containing zinc and copper carboxylates. It gives two gas chromatographic options: one using a capillary column and one using a packed column. It is applicable primarily to the analysis of preservative formulations conforming to BS 5707.

Methods of analysis of wood preservatives and treated timber. Determination of carboxylic acid type in zinc and copper carboxylate preservative solutions by gas chromatography

BS 8417:2003 木材防腐.推荐规范

This British Standard gives recommendations and guidance for the preservative treatment of timber to provide protection against biodeterioration in certain specified end-use situations in the United Kingdom. It recommends levels of penetration and retention of preservative, from the classes defined in BS EN 351-1, for different timber components and takes into account the natural durability and treatability of the timber employed, the biological hazard class and the desired service life. It also provides guidance on establishing whether a specified level of treatment has been achieved. This British Standard applies only to solid wood, including glued laminated timber. It does not apply to panel products, as no European Standards have been published on the preservation of these products. This British Standard does not apply to treatments regarded as remedial in nature or to those primarily designed to influence the performance of timber in fire. NOTE In the United Kingdom, only preservatives approved under the Control of Pesticides Regulations 1986 [2] are permitted for the treatment of timber.

Preservation of timber - Recommendations

ARMY A-A-59276 VALID NOTICE 1-2003 木材防腐剂:水性或水还原

A-A-59276, dated 29 June 1998, has been reviewed and determined to be valid for use in acquisition

WOOD PRESERVATIVES: WATERBORNE OR WATER REDUCIBLE

PD CEN/TR 14723:2003 木材和木基制品耐用性.不接触地面的木材防腐剂的现场和加速处理试验（FACT）

This Technical Report presents a summary of the research of the S.M.T. Project: F.A.C.T, SMT4 CT96 2135. As such it details the supporting information for the proposals for a new conditioning standard to replace EN 73 and EN 84 and for modification and validation of ENV 12037. The full report is presented and referenced to Technical annexes, which are available on request. The FACT project involved the study of the fate of chosen wood preservatives in field and laboratory tests and the affect on biological performance. The work consisted of four core tasks and associated sub-tasks designed to provide the scientific background to the proposals made. Task 1 This consisted of a study of artificial weathering techniques for the conditioning of treated test blocks prior to biological test. It was originally hoped that it might be possible to relate different weathering cycles to the different climatic conditions found within Europe. However this did not prove possible but it is possible to recommend a single weathering cycle to replace the use of EN 73 and EN 84. A draft experimental standard has been prepared based on the findings of this work. All the supporting data and associated studies are summarised in this Technical report in clauses 5 and 6. Task 2 This task consisted of an extensive field test based on ENV 12037 and associated sub-tasks. The method proved very robust but significant modifications are recommended and the ENV is to be redrafted in the light of results contained in this report. This field test should be considered as ‘simulated service trial’ rather than an accelerated field test; a concept that needs careful consideration within the EN 599 framework. Sub-tasks 2.3 and 2.4 examined the suitability of the method for composites and the testing of naturally durable timbers. At this stage it is too early to make recommendation for their inclusion in the standard but the results look promising and the method will probably be modified at a later revision. Tasks 3 and 4 These tasks examined the role of bio-conditioning of test samples in ‘use class’ 3 and 4. The results are presented in clauses 8 and 9 and clearly indicate the importance of this subject. It is recommended that urgent attention is given to taking this work further particularly for the testing of organic based preservatives. Although not yet ready for standardisation, the results presented here will prove invaluable to industry in designing development programmes for the new generation of organic based preservatives. In summary: a new experimental standard will be produced to replace EN 73 and EN 84 for the physical conditioning of test blocks; ENV 12037 will be modified to take into account the extensive findings of the project; the use of ENV 12037 for natural durability and composite testing will be considered when more results are available; further work on biological conditions is urgently recommended.

Durability of wood and wood-based products - Field and accelerated conditioning tests (FACT) for wood preservative out of ground contact

PD CEN/TR 14823:2003 木材和木材制品的耐久性.木材中五氯苯酚的定量测定.气体色谱法

This Technical Report specifies a laboratory method of determining the pentachlorophenol content of wood. The method is applicable to all types of PCP- treated wood and wood-based materials as well as for the analysis of waste timber with respect to its PCP content. The method has a quantification limit corresponding to 100 μg PCP per kilogram of wood material expressed as dry matter. The method described has a measurement range up to PCP contents of 25 mg/kg of dry matter. These figures refer to the given example (where an aliquot of 1 ml of the extract is used for acetylation, see 8.4). NOTE 1 If lower quantification limits are required, a higher volume of extract aliquot can be used for derivatisation. NOTE 2 This method could have some modifications with some wood species as hardwoods.

Durability of wood and wood-based products - Quantitative determination of pentachlorophenol in wood - Gas chromatographic method

ASTM D6815-02a 木制和木基产品的荷载和蠕变效应的持续时间的评价的标准规范

1.1 This specification provides a procedure for testing and evaluating duration of load and creep effects of wood and wood-based materials relative to an accepted duration of load adjustment model. This specification was created for products that are currently covered by a consensus standard (for example, lumber, structural composite lumber and structural-use panels). This procedure is intended to demonstrate the engineering equivalence to the duration of load and creep effects of visually graded lumber as specified in Practice D 245 for a product under evaluation used in dry service conditions. This procedure is not intended to evaluate the performance of products under impact loading. Quantification of specific duration of load or creep factors is beyond the scope of this specification. For further guidance regarding the applicability of this specification refer to X1.1 in the Commentary.1.2 Use of the procedure in this specification to determine equivalence to the Practice D 245 duration of load relationship is limited to solid wood and wood-based products whose long term load behavior is similar to that of solid wood. Equivalence demonstrated in this specification is dependent upon evaluation of a product's 90-day (minimum) creep-rupture performance. In this evaluation, three criteria must be satisfied: (1) adequate strength over a 90-day period, (2) decreasing creep rate, and (3) limited fractional deflection. A summary of the development of these criteria and the underlying assumptions behind them is provided in the Commentary in Appendix X1 and Appendix X2.1.3 Long term degradation phenomena not described by a creep-rupture model are not addressed in this standard (see Commentary X1.2.4).

Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products

ASTM D2278-02 圆柱形样品现场评定木材防腐剂的标准试验方法

1.1 This test method covers the determination of the relative effectiveness of wood preservatives in round posts set in the ground in field plots. Two tests are described, one for small (3 to 5 in. (80 to 130 mm) in diameter) sapwood posts which is the preferred test if major interest lies in testing the preservative when fairly evenly distributed throughout the piece, and the second for large posts (7 to 10 in. (180 to 250 mm) in diameter) which is preferred when the preservative is tested under conditions of gradient retention and distribution normally encountered in commercial operations.1.2 The requirements for preparation of the material for testing and the test procedures appear as follows:SectionTest Plot4Test Specimens5Treatment Procedure6After-Treatment Handling of Posts7Installation of Posts8Inspection of Specimens9Evaluation of Results10Reports111.3 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents of inch-pound units may be approximate.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Field Evaluation of Wood Preservatives in Round Post-Size Specimens

ASTM D1758-02 用木桩现场试验评定木材防腐剂的标准试验方法

1.1 This test method covers accelerated procedures for determining the relative permanence and effectiveness of wood preservatives in stakes exposed in field plots.1.2 The requirements for preparation of the material for testing and the test procedures appear in the following order: SectionsSummary of Test Method3Test Plot4Test Specimens5Pretreatment Selection of Test Stakes6Treatment Procedure7After Treatment Handling of Test Stakes8Installation of Stakes9Inspection of Specimens10Evaluation of Results11Reports121.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use

Standard Test Method of Evaluating Wood Preservatives by Field Tests with Stakes

ASTM D6815-02 木制和木基产品的荷载和蠕变效应的持续时间的评价的标准规范

1.1 This specification provides a procedure for testing and evaluating duration of load and creep effects of wood and wood-based materials relative to an accepted duration of load adjustment model. This specification was created for products that are currently covered by a consensus standard (for example, lumber, structural composite lumber and structural-use panels). This procedure is intended to demonstrate the engineering equivalence to the duration of load and creep effects of visually graded lumber as specified in Practice D 245 for a product under evaluation used in dry service conditions. This procedure is not intended to evaluate the performance of products under impact loading. Quantification of specific duration of load or creep factors is beyond the scope of this specification. For further guidance regarding the applicability of this specification refer to X1.1 in the Commentary.1.2 Use of the procedure in this specification to determine equivalence to the Practice D 245 duration of load relationship is limited to solid wood and wood-based products whose long term load behavior is similar to that of solid wood. Equivalence demonstrated in this specification is dependent upon evaluation of a product's 90-day (minimum) creep-rupture performance. In this evaluation, three criteria must be satisfied: (1) adequate strength over a 90-day period, (2) decreasing creep rate, and (3) limited fractional deflection. A summary of the development of these criteria and the underlying assumptions behind them is provided in the Commentary in Appendix X1 and Appendix X2.1.3 Long term degradation phenomena not described by a creep-rupture model are not addressed in this standard (see Commentary X1.2.4).

Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products

DIN V ENV 807:2001 木材防腐剂.防霉菌腐烂和其它陆栖微生物效果的测定

Wood preservatives - Determination of the effectiveness against soft rotting micro-fungi and other soil inhabiting micro-organisms; German version ENV 807:2001

DD ENV 807-2001 木材防腐剂.抗微真菌软腐蚀和其他土壤中微生物效果的测定

Wood preservatives. Determination of the effectiveness against soft rotting micro-fungi and other soil inhabiting micro-organisms

BS DD ENV 807:2001 木材防腐剂.防腐剂抗轻腐蚀微生霉菌和其他土壤抑制微生物有效性的测定

Wood preservatives - Determination of the effectiveness against soft rotting micro-fungi and other soil inhabiting micro-organisms

NF B54-301*NF EN 13017-1:2001 实心木板.根据表面外观分类.第1部分:软木

Solid wood panels - Classification by surface appearance - Part 1 : softwood.

AIR FORCE QPL-6529-24 NOTICE 1-2001 飞机引擎防腐剂

Military Specification MIL-C-6529C, which covers the products listed on QPL-6529-24, was inactivated for new design on 3 December 1997.

CORROSION PREVENTIVE, AIRCRAFT ENGINE

ASTM D5583-00 用麴霉属生物鉴定法作木材防腐保存检测和评定的标准试验方法

1.1 This test method covers a non-chemical, biological procedure for assaying wood for approximate preservative content (Note 1). It requires minimal equipment and technical proficiency. No costly equipment is needed other than a small autoclave for preparing fungal media. It does not require composite samples, such as called for in Specification D1760 to ascertain preservation retentions, therefore it is used to assess retention at individual locations. Note 1--With appropriate, simple adaptation, the method can be used with other products besides wood, such as fungicidal paints and glues. The assaying is done wherever it is convenient, since aseptic precautions are not required except for maintaining a pure stock culture of the assay fungus. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Detection and Estimation of Retention of Wood Preservatives by Aspergillus Bioassaying

ANSI/ASTM D5583:2000 曲霉菌生物试验法检测和估计木材防腐剂有效期的方法

This test method covers a non-chemical, biological procedure for assaying wood for approximate preservative content (Note 0). It requires minimal equipment and technical proficiency. No costly equipment is needed other than a small autoclave for preparing fungal media. Since this test method does not require composite samples to ascertain preservation retentions, therefore it is used to assess retention at individual locations. Note 0With appropriate, simple adaptation, the method can be used with other products besides wood, such as fungicidal paints and glues. The assaying is done wherever it is convenient, since aseptic precautions are not required except for maintaining a pure stock culture of the assay fungus. The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Detection and Estimation of Retention of Wood Preservatives by Aspergillus Bioassaying