J16 阀门 标准查询与下载

JB/T 13600-2018 水轮机进水双密封蝶阀

Turbine water inlet double seal butterfly valve

JB/T 13597-2018 低温环境用阀门电动装置 技术条件

Technical conditions for electric devices of valves used in low-temperature environments

JB/T 10530-2018 氧气用截止阀

Stop valve for oxygen

JB/T 13604-2018 氧化铝专用料浆阀

Special slurry valve for alumina

JB/T 13601-2018 液压驱动装置 技术条件

Hydraulic drive device technical conditions

JB/T 13602-2018 放空截止阀

Vent stop valve

DIN EN ISO 17871:2018 气瓶. 速释气瓶阀门. 规格和型式试验 (ISO 17871-2015+Amd 1-2018); 德文版本EN ISO 17871-2015+A1-2018

This International Standard in conjunction with ISO 10297:2014 and ISO 14246:2014 specifies design, type testing, marking and manufacturing tests, and examinations requirements for quick-release cylinder valves intended to be fitted to refillable transportable gas cylinders which convey non-toxic, non-oxidizing, non-flammable and non-corrosive compressed or liquefied gases or extinguishing agents charged with compressed gases to be used for fire-extinguishing, explosion protection, and rescue applications. This International Standard covers the function of a quick-release cylinder valve as a closure. This International Standard does not apply to quick-release cylinder valves for cryogenic equipment, for portable fire extinguishers, or for liquefied petroleum gas (LPG).

Gas cylinders - Quick-release cylinder valves - Specification and type testing (ISO 17871:2015 + Amd 1:2018); German version EN ISO 17871:2015 + A1:2018

DIN EN 12516-1:2018-11 工业用阀.外壳设计强度.第1部分:钢阀外壳用造表方法;德文版本EN 12516-1-2014

Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells; German version EN 12516-1:2014

JIS B 8376:2018 气动流体动力.速度控制阀

Pneumatic fluid power -- Speed control valves

JB/T 13517-2018 V 型球阀

V type ball valve

DIN EN 16668:2018 工业阀.作为承压附件的金属阀要求和试验; 德文版本EN 16668-2016+A1-2018

This European standard applies to metallic valves as pressure accessories for industrial applications with a maximum allowable pressure PS greater than 0,5 bar in accordance with the European legislation for pressure equipment and specifies minimum requirements applicable to design, manufacture, testing, materials and documentation. All relevant essential safety requirements of the European legislation for pressure equipment applicable to valves have been taken into consideration and are addressed in this standard. This standard is not applicable to: - safety valve and bursting disc (a safety accessory), - sight glass with its frames (component of a pressure equipment) and - measurement chambers. For other exclusions refer to the European legislation for pressure Equipment.

Industrial valves - Requirements and testing for metallic valves as pressure accessories; German version EN 16668:2016+A1:2018

JB/T 8864-2018 阀门气动装置 技术条件

Valve pneumatic device technical conditions

JB/T 13460-2018 液化天然气轴流式止回阀

Liquefied natural gas axial flow check valve

JB/T 13459-2018 铜制浮子式自动排气阀

Copper float type automatic exhaust valve

JB/T 13458-2018 保温夹套阀门

Insulation jacketed valve

DL/T 1822-2018 电站用抽汽止回阀订货验收导则

Guidelines for order acceptance of steam extraction check valves for power stations

DL/T 1821-2018 火电站闸阀、截止阀检修导则

Guidelines for overhauling gate valves and globe valves in thermal power stations

JIS B 2062:2018 普通输水管道用闸阀

Sluice valves for ordinary water piping

BS EN 736-1:2018 阀门 术语 阀门类型的定义

Valves. Terminology. Definition of types of valves

DIN EN ISO 11363-2:2018 气瓶.气瓶阀门连接用17E和25E椎管螺纹.第2部分:检验计量表(ISO 11363-2-2017);德文版本EN ISO 11363-2-2017

This International Standard specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper threads specified in ISO 11363-1 (i.e. 17E and 25E threads). This International Standard provides examples of calculations for thread gauge dimensions on the large end diameter (Annex A) and draws attention to the limitations of the gauging system specified (Annex B).

Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2017); German version EN ISO 11363-2:2017