共找到 4134 条与 焊接与切割 相关的标准,共 276 页
本标准规定了铸铁焊条及焊丝的分类、型号、技术要求及试验方法等内容。 本标准适用于灰口铸铁、可锻铸铁,球墨铸铁及某些合金铸铁补焊用电焊条及气焊焊丝。
Covered electrodes and welding rods for welding cast iron
本标准规定了焊缝符号表示方法。 本标准适用于金属熔化焊及电阻焊。
Welds-symbolic representation on drawings
本标准规定了用环形或螺形缺口试样进行的插销冷裂纹试验方法。 本标准适用于钢材焊接冷裂敏感性的评定。 本焊接方法、钢材和应力给定的条件下也适用对比焊接材料特性。
Welding--Cold cracking test method using implants
本标准规定了钢焊接接头的各种坡口形式与坡口尺寸。 本标准适用于气焊(用于薄板)、手工电弧焊及气体保护焊焊接的碳钢、低合金钢焊接接头。
Basic forms and sizes of weld grooves for gas welding manual arc welding and gas--Shielded arc welding
本标准规定了埋弧焊焊缝坡口的基本形式和尺寸。 本标准适用于碳钢和低合金钢埋弧焊焊接接头。
Basic forms and sizes of weld grooves for submerged arc welding
本标准规定了测定焊接接头疲劳裂纹扩展速率的试验方法。 本标准适用于室温(15~35℃)及大气环境下测定金属材料熔化焊焊接接头(焊缝金属及热影响区)大于10mm/周的恒幅循环载荷下的疲劳裂纹扩展速率。在非室温、非大气环境下的焊接接头裂纹扩展速率试验,亦可参照本方法。
Test method for fatigue crack growth rates of welded joints
本标准适用于熔化极惰性气体保护焊、钨极惰性气体保护焊和气焊等焊接工艺方法用的铜及铜合金焊丝.
Welding wire and rods of copper and copper alloys
Method of the strength test for brazed and soldered seam
本标准为软、硬钎焊钎缝的常规机械性能而制定的。 本标准适用于黑色金属、有色金属及其合金的硬钎焊钎缝在冷态、室温、热态时的瞬时拉伸、剪切强度和高温蠕变强度以及软钎焊钎缝在冷态、室温、热态时的瞬时剪切强度及蠕变强度的测定。 本标准规定了所用拉伸试样和剪切试样的形状以及统一的操作方法,以使试验结果可以重现与比较。
Method of the strength test for brazed and soldered seam
本标准规定用T型角焊接试样,在静压下弯曲变形后,根据焊趾端有无裂纹及裂纹扩展的特征来评定碳素钢及低合金结构钢钢板的焊接性。
Method of bend test for T type fillet welded joint
本标准适用于金属熔化焊。
Classification of imperfections in metallic fusion welds, with explanations
本标准适用于压力容器、钢结构、起重机提升设备、船舶、工程机械、运输设备等的钢熔化焊接头。 本标准不包括由于整体设计不良而出现的各种影响因素。
Technical factors influencing the quality of the fusion welded joints in steel
本标准规定用阿拉伯数字代号来表示金属焊接及钎焊等各种焊接方法,此数字代号均可在图样上作为焊接方法来使用。本标准与GB324-80《焊缝代号》配套使用。
Welding,brazing,braze welding and soldering of metals--List of processes for symbolic representation on drawings
本标准适用于手工电弧焊接,是以热影响区最高硬度来相对地评价钢材冷裂倾向的试验方法。
Weldability testing--Testing method of maximum hardness in weld heat-affected zone
本标准适用于碳素钢和低合金钢焊接接头的斜Y型坡口焊接裂纹试验。
Weldability testing Method of Y-groove cracking test
本标准适用于低合金钢和碳素钢搭接接头焊接裂纹试验。
Weldability testing--Method of controlled thermal severity cracking test
本标准适用于碳素钢的T型接头角焊缝裂纹试验。
Weldability testing--Method of cracking test for welded tee joint
本标准适用于GB981-76《低碳钢和低合金高强度钢焊条》和GB983-76《不锈钢焊条》等焊条的焊接裂纹试验。
Weldability testing--Method of FISCO cracking test
本国家标准规定了直径为3.15至6.3mm的碳钢和低合金高强度钢涂料焊条效率、焊条金属回收率和熔敷系数的测定方法。 本国家标准所规定的测量精度在实际应用中是足够的,因为每一批焊条的性质总会有一定的波动。
Covered electrodes--Determination of the efficiency,metal recovery and deposition coefficient
焊缝金属和焊接接头的疲劳试验法
Weld beads metal and welds--Fatigue tests
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号