J71 泵 标准查询与下载

DIN EN ISO 9905/A1:2011 离心泵技术规范.I级.修订条款1(ISO 9905-1994/AMD 1-2011);德文版本EN ISO 9905-1997/A1-2011

Technical specifications for centrifugal pumps - Class I - Amendment 1 (ISO 9905:1994/AMD 1:2011); German version EN ISO 9905:1997/A1:2011

JB/T 11171-2011 溴化锂吸收式空调机内用屏蔽电泵

本标准规定了溴化锂吸收式空调机内用屏蔽电泵（以下简称电泵）的术语和定义、型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输与贮存等。 本标准适用于设计压力为0.5MPa,输送介质温度范围为0℃～150℃、不含固体颗粒的溴化锂溶液和冷剂水电泵。

Canned motor pump with lithium-bromide absorption type for conditioner

JB/T 11170-2011 凝结水和乏汽闭式回收水泵装置

本标准规定了凝结水和乏汽闭式回收水泵装置的术语和定义、分类与基本参数、技术要求、自控柜和仪表、材料和单元件、试验方法、检验规则、供货要求等。 本标准适用于蒸汽供热系统中凝结水和乏汽回收使用的集水罐公称压力小于或等于PN16,介质最高温度不大于200℃的凝结水和乏汽闭式回收水泵装置。

Closed condensate and exhausted steam recovery pump uint

JB/T 8857-2011 离心式潜污泵

本标准规定了离心式潜污泵（以下简称泵）的型式与基本参数、技术要求、试验方法、检验规则、保证期、标志、包装、运输和贮存。 本标准适用于所输送液体中含有非磨蚀性固体颗粒、纤维、污杂物（如城市生活污水、化学工业废水等）的泵。

Centrifugal submersible sewage pumps

JB/T 8645-2011 潜水螺杆泵

本标准规定了潜水螺杆泵（以下简称泵）的术语和定义、型式、型号与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于潜水螺杆泵。

Submersible screw pumps

JB/T 7743-2011 旋涡泵

本标准规定了旋涡泵（以下简称泵）的型式、型号、基本参数、旋转方向、技术要求、试验和试验方法、检验规则、标志、使用说明书、包装、运输和贮存。 本标准适用于输送不含固体颗粒、运动粘度不大于37.4 mm/s液体的机械密封泵和输送易燃、易爆、易挥发、有毒、有腐蚀性以及贵重液体的磁力传动泵。被输送液体的温度：机械密封泵为-20℃～120℃,磁力传动泵为-20℃～250℃。

Vortex pump

JGJ/T 10-2011 混凝土泵送施工技术规程

本规程适用于建筑工程、市政工程的混凝土泵送施工，本规程不适用于轻骨料混凝土的泵送施工。

Technical specification for construction of concrete pumping

ISO 9908:1993/Amd 1:2011 离心泵技术规格.类Ⅲ.修改件1

Technical specifications for centrifugal pumps - Class Ⅲ; Amendment 1

Technical specifications for centrifugal pumps - Class Ⅲ; Amendment 1

ISO 9905:1994/Amd 1:2011 离心泵技术规格.类I.修改件1

Technical specifications for centrifugal pumps - Class I; Amendment 1

Technical specifications for centrifugal pumps - Class I; Amendment 1

MT/T 1119-2011 煤矿坑道钻探用往复式泥浆泵

本标准规定了煤矿坑道钻探用往复式泥浆泵的术语和定义、符号、型号与基本参数、技术要求、试验条件、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于在煤矿坑道钻探施工中使用的往复式泥浆泵。

To-and-fro mud pump used in coal mine tunnel drilling

DIN EN 809:2011 液体泵和泵机组.一般安全性要求;德文版本EN 809-1998+A1-2009 + AC-2010

Pumps and pump units for liquids - Common safety requirements; German version EN 809:1998+A1:2009 + AC:2010

ANSI/HI 12.1-12.6-2011 离心式淤浆泵的术语,定义,应用和操作

The Slurry Pump Committee will limit its activity to the above matters to rotodynamic pumps that handle abrasive slurries. Excluded are applications for wastewater pump.

Rotodynamic (Centrifugal) Slurry Pumps for Nomenclature, Definitions, Applications, and Operation

ANSI/HI 14.6-2011 回转动力泵.液压性能验收试验

This standard was initiated and developed jointly and simultaneously by the Hydraulic Institute Test Committee and by ISO TC 115 SC2 / WG2. It represents an update of the combined contents of ANSI/HI 1.6-2000 and ANSI/HI 2.6-2000 as well as ISO9906:1999. ANSI Essential Methods and the ISO Directives have been used to review, consensus building, and in the balloting of this standard.

Rotodynamic Pumps - Hydraulic Performance Acceptance Tests

ANSI/HI 9.6.2-2011 应用的喷嘴负载评估用转子动力泵

This standard includes recommendations for assessment of applied nozzle loads for the following pump types. When specified by the user, pumps supplied shall conform to these requirements. a) Horizontal end suction single stage (ANSI/ASME B73.1, B73.3, and B73.5M) b) Vertical in-line single stage (ANSI/ASME B73.2) c) Axial split case single and two stage d) Vertical turbine short set pumps

Rotodynamic Pumps for Assessment of Applied Nozzle Loads

ASTM D5337-11 个人采样泵校正流量的标准操作规程

Most occupational exposure assessment methods require the use of personal sampling pumps to collect air samples at typical workplace sampling rates, with sampling volumes specified by (a) particular procedure(s). The precision and bias of these methods are directly affected by the precision and bias of the pumps used to measure the air volume(s) sampled.1.1 This practice describes the calibration of sampling pumps commonly used for monitoring personal airborne exposures in the work-place.1.2 This practice includes procedures for describing primary and secondary calibration techniques.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Flow Rate for Calibration of Personal Sampling Pumps

DIN EN 60335-2-41:2010 家用和类似电器.安全性.第2-41部分:泵的详细要求(IEC 60335-2-41-2002 + A1-2004 + A2-2009).德文版本EN 60335-2-41-2003 + A1-2004 + A2-2010

Household and similar electrical appliances - Safety - Part 2-41: Particular requirements for pumps (IEC 60335-2-41:2002 + A1:2004 + A2:2009); German version EN 60335-2-41:2003 + A1:2004 + A2:2010

BS EN ISO 13709:2009 石油,石化和天然气工业用离心泵

Centrifugal pumps for petroleum, petrochemical and natural gas industries CD-ROM

DB35/T 1015-2010 射流式自吸电泵

本标准规定了射流式自吸电泵的型式、型号和基本参数、技术要求、试验方法、检验规则、标志、 包装、运输和贮存。 本标准适用于射流式自吸电泵 (以下简称电泵)。

Jet type self-priming electric pump

DB35/T 1014-2010 旋涡式自吸电泵

本标准规定了旋涡式自吸电泵的型式、型号和基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于旋涡式自吸电泵 (以下简称电泵)。

Vortex self-priming electric pump

DB35/T 1013-2010 旋涡式微型电泵

本标准适用于旋涡式微型电泵 (以下简称电泵)。

Vortex micro electric pump