J71 泵 标准查询与下载

DB35/T 1013-2010 旋涡式微型电泵

本标准适用于旋涡式微型电泵 (以下简称电泵)。

Vortex micro electric pump

DB35/T 1016-2010 单级单吸离心式电泵

本标准规定了单级单吸离心式电泵的型式、型号和基本参数、技术要求、试验方法、检验规则、标 志、包装、运输和贮存。 本标准适用于单级单吸离心式电泵(以下简称电泵)。

Single-stage single-suction centrifugal electric pump

DIN EN ISO 13709:2010 石油、石化和天然气工业用离心泵

This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-bearings pumps and vertically suspended pumps (see Table 1). Clause 9 provides requirements applicable to specific types of pump. All other clauses of this International Standard are applicable to all pump types. Illustrations are provided of the various specific pump types and the designations assigned to each specific type.

Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009); English version EN ISO 13709:2009, only on CD-Rom

DIN EN 12162:2010 液体泵.安全要求.静液压试验程序.德文版本EN 12162-2001+A1-2009

This standard specifies the hydrostatic test procedure to be applied to pressure containing parts of all types of liquid pumps including any auxiliary equipment making up a pump unit as described in the scope of EN 809:1998, except : domestic water pumps within the scope of EN 60335-2-41:1996 or EN 60335-2-51:1997; domestic circulation pumps within the scope of EN 1151:1999 ; submersible pumps within the scope of prEN 13386:1998 ; fire-fighting pumps with primers within the scope of prEN 1028-1:1993 and prEN 1028-2:1993 ; pump parts with a maximum allowable working pressure below 0.1 bar. Requirements are included for applying an hydrostatic test at different pressures to separate zones within a pump which are subject to different allowable maximum working pressures. This standard is for pumps and pump units which are placed upon the market after the publication date of the standard.

Liquid pumps - Safety requirements - Procedure for hydrostatic testing; German version EN 12162:2001+A1:2009

DIN EN ISO 15783:2010 无封装旋翼动力泵.级别II.规范(ISO 15783-2002 + Amd.1-2008).德文版本EN ISO 15783-2003+A1-2008

This standard covers the requirements for sealless rotodynamic pumps that are driven with permanent magnet coumpling, or with canned motor and are mainly used in chemical process, water treatment and petrochemical industries.

Seal-less rotodynamic pumps - Class II - Specification (ISO 15783:2002 + Amd.1:2008); German version EN ISO 15783:2003 + A1:2008

JB/T 6434-2010 输油齿轮泵

本标准规定了输油齿轮泵(包括外啮合齿轮泵和内啮合齿轮泵)的型式、基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于输送不含固体颗粒和纤维，温度不高于150℃，粘度范围：5×10m/s～1.5×10m/s(外啮合齿轮泵)、1×10m/s～3×10m/s(内啮合齿轮泵)，具有润滑性的油品和性质类似油品的液体的泵。

Oil-transferring gear pumps

JB/T 11008-2010 高速部分流泵

本标准规定了石油、重化学和天然气工业用高速部分流泵(以下简称泵)的型式与基本参数、设计、检查和试验、交付准备、标志、包装、运输和贮存等。 本标准适用于采用齿轮箱增速和电动机变频增速的高速部分流泵。

High speed partial emission pump

JB/T 6884-2010 液下式离心泵.型式与基本参数

本标准规定了液下式离心泵的型式、型号与基本参数。 本标准适用于输送不含固体颗粒或少量的固体颗粒(固体质量不大于1.5%，粒度小于0.5mm)的腐蚀性液体的泵。

Submerged certrifugal pump.Types and basic parameters

JB/T 11007-2010 高剪切匀浆泵、乳化泵

本标准规定了高剪切匀浆泵、高剪切乳化泵(以下简称“泵”)的型式与基本参数、技术要求、试验和检验、交付、标志、包装、发运、贮存和保证事项等。 本标准适用于物料粘度小于50000mPa·s的卧式、两端支承式稿件切匀浆泵和物料粘度小于1500mPa·s的卧式、悬臂式乳化泵。

High shear homogenizing pump and emulsion pump

ANSI/UL 79-2010 石油产品输送系统用动力泵(提案日期2010年4月30日)

Revisions to the pressure gauge requirements.

Standard for Safety for Power-Operated Pumps for Petroleum Dispensing Products (proposals dated 4/30/10)

ANSI/HI 5.1-5.6-2010 无密封离心泵的术语,定义,应用,操作和测试

This standard covers types and nomenclature, definitions, design and application, installation, operation and maintenance, and test of sealless rotodynamic pumps driven by canned motors or magnetic couplings. Not included are submersible wastewater pumps that do not have external shaft seals and are therefore not susceptible to external shaft leakage.

Sealless Rotodynamic Pumps for Nomenclature, Definitions, Application, Operation, and Test

ANSI/HI 1.4-2010 转子动力(Cent.)泵的安装,操作和维修

This standard is for centrifugal and regenerative turbine pumps of all industrial/commercial types, except vertical single and multistage diffuser types. It provides information regarding installation, operation, and maintenance. Pre-installation, storage recommendations, and site preparation are covered as well.

Rotodynamic (Cent.) Pumps for Installation, Operation & Maintenance

ANSI/HI 10.1-10.5-2010 气动标准

The Air Operated Pump Standard developed shall include, but are not limited to: types and nomenclature, definitions, design and application, installation, operation and maintenance.

Air Operated Standard

ANSI/HI 3.6-2010 旋转泵测试

This standard applies to industrial/commercial rotary positive displacement pumps. It includes detailed procedures on the setup and conduct of hydrostatic and performance tests of such pumps.

Rotary Pump Test

ANSI/HI 9.6.7-2010 (离心式)叶片泵的设计与应用

This standard covers the performance correction of rotodynamic (centrifugal and vertical) pumps handling liquids exhibiting Newtonian-like characteristics with a viscosity greater than that of water. The standard includes a generalized method for predicting the performance of rotodynamic pumps. Theoretical methods based on loss analysis may provide more accurate predictions of the effects of liquid viscosity on pump performance when the geometry of a particular pump is known in more detail.

Rotodynamic (Centrifugal) Pumps for Design and Application

ASTM D7623-10 用燃烧金汞齐和冷蒸气原子吸收法对原油总汞的标准试验方法

The emission of mercury during crude oil refining is an environmental concern. The emission of mercury may also contaminate refined products and form amalgams with metals, such as aluminum. When representative test portions are analyzed according to this procedure, the total mercury is representative of concentrations in the sample.1.1 This test method covers the procedures to determine the total mercury content in a sample of crude oil. 1.2 The test method may be applied to crude oil samples containing between 5 to 400 ng/mL of mercury. The results may be converted to mass basis, and reported as ng/g of mercury. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Total Mercury in Crude Oil Using Combustion-Gold Amalgamation and Cold Vapor Atomic Absorption Method

ASTM D7622-10 用燃烧和直接冷蒸气塞曼背景校正原子吸收法对原油总汞的标准试验方法

The emission of mercury during crude oil refining is an environmental concern. The emission of mercury may also contaminate refined products and form amalgams with metals, such as aluminum. When representative test portions are analyzed according to this procedure, the total mercury is representative of concentrations in the sample.1.1 This test method covers the procedure to determine the total mercury content in a sample of crude oil. This test method can be used for total mercury determination in natural and processed liquid and oil products (gasoline, naphtha, etc.). 1.2 This test method may be applied to samples containing between 5.0 to 350 ng/mL of mercury. The results may be converted to mass basis. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Total Mercury in Crude Oil Using Combustion and Direct Cold Vapor Atomic Absorption Method with Zeeman Background Correction

ANSI/HI 10.6-2010 压缩空气驱动泵试验标准

This standard provides the reader with information regarding air-operated reciprocating diaphragm and bellows pumps. Technical documents developed shall include, but are not limited to: types and nomenclature, definitions, design and application, installation, operation and maintenance, and test.

Air Operated Pump Test Standard

ANSI/HI 4.1-4.6-2010 无密封旋转式泵

This standard covers the unique features of sealless rotary pumps and includes sections on types and nomenclature; definitions; design and applications; installation, operation, and maintenance; and test. Because of the variety of rotary pump configurations available and the broad range of applications, familiarization with Hydraulic Institute Standards ANSI/HI 3.1 - 3.5 Rotary Pumps for Nomenclature, Definitions, Application and Operation and ANSI/HI 3.6 Rotary Pump Tests is recommended.

Sealless Rotary Pumps

KS B ISO 13562-1:2009 伸缩臂式工业车辆.第1部分:稳定性试验

이 표준은 자주식과 좌식의 카운터 밸런스 지게차로 다음과 같은 다양한 고소 지게차에 적용한

Industrial variable-reach trucks-Part 1:Stability test