共找到 506 条与 裸电线 相关的标准,共 34 页
本标准适用于制造电线电缆及电机电器用的圆铝线。
Round aluminum wire for electrical purposes
本标准的规定与国际电工委员会(IEC)28的规定相一致。
Round copper wire for electrical purposes
1.1?This specification covers aluminum-alloy 6201-T81 (hard, solution heat-treated, cold worked, and artificially aged) and 6201-T83 (hard, higher conductivity, solution heat-treated, cold worked, and artificially aged) round wire for electrical purposes. Note 1:?The alloy and t
Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes
Steel strands for overhead conductors
Aluminum alloy wire for pre-twisted fittings for overhead lines
Copper tape for cable shielding
Electricians use fire method to refine highly conductive copper rods
Energy consumption limit per unit product for overhead conductors
Guidelines for calculating energy efficiency index for overhead conductor manufacturers
Superconductivity -- AC loss measurements -- Magnetometer methods for hysteresis loss in superconducting multifilamentary composites
Superconductivity -- Matrix to superconductor volume ratio measurement -- Copper to non-copper volume ratio of Nb3Sn composite superconducting wires
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance of application characteristics. Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specific ratio width/thickness are given in IEC 60317-0-9.
Specifications for particular types of winding wires - Part 68: Polyvinyl acetal enamelled rectangular aluminium wire, class 120
Aluminum tube supporting heat-resistant aluminum alloy expanded diameter wire
Hard-drawn aluminium wires for electric purposes
Conductors for overhead lines - Round wire concentric lay stranded conductors; German version EN 50182:2001, Corrigendum to DIN EN 50182:2001-12; German version EN 50182:2001/AC:2013
1.1 This specification covers aluminum 1350-H19 (extra hard), 1350-H16 or -H26 (3/4 hard), 1350-H14 or -H24 (1/2 hard), and 1350-H142 or -H242 (1/2 hard), bare concentric-lay-stranded conductors constructed with a straight round central wire surrounded by one or more layers of helically layed wires. The conductors are for general use for electrical purposes (Explanatory Note 1 and Note 2). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 For density, resistivity and temperature, the values stated in SI units are to be regarded as standard. Note 1: Prior to 1975, aluminum 1350 was designated as EC aluminum. Note 2: The aluminum and temper designations conform to ANSI Standard H35.1/H35.1M. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527. Note 3: Sealed conductors that are intended to prevent longitudinal water propagation and are further covered/insulated are also permitted within the guidelines of this specification.
Standard Specification for Concentric-Lay-Stranded Aluminum 1350 Conductors
Expanded diameter steel core aluminum stranded wire
本标准规定了钢芯软铝绞线的产品命名及表示方法、技术要求、试验方法、检验规则、包装和标志等。本标准适用于架空输电线路用钢芯软铅绞线。
The annealed aluminium conductors steel supported
本标准规定了钢芯耐热铝合金架空导线的产品命名及表示方法、要求、试验、包装和标志等内容。本标准规定的钢芯耐热铝合金架空导线包括钢芯耐热铝合金绞线和铝包钢芯耐热铝合金绞线,其结构由下述的金属单线组合而成:a)架空绞线用耐热铝合金线最高允许连续运行温度为150℃的耐热铝合金线,型号为NRLH1,符合GB/T 30551-2014;最高允许连续运行温度为150℃的高强度耐热铝合金线,型号为NRLH2,符合GB/T30551-2014。b)架空绞线用镀锌钢线1级强度镀锌钢线,型号为G1A,符合GB/T 3428-2012;2级强度镀锌钢线,型号为G2A,符合GB/T 3428-2012;3级强度镀锌钢线,型号为G3A,符合GB/T 3428-2012;4级强度镀锌钢线,型号为G4A,符合GB/T 3428-2012;5级强度镀锌钢线,型号为G5A,符合GB/T 3428-2012。c)电工用铝包钢线14%IACS铝包钢线,型号为 LB14,符合 GB/T 17937-2009;20.3%IACS铝包钢线,型号为 LB20A,符合 GB/T 17937-2009。镀锌钢线的镀层金属亦可采用特种镀锌层,如锌-5%铝-稀土合金镀层、55%铝-锌合金镀层等耐蚀性较好的镀层,但机械和电气性能仍应符合GB/T 3428-2012。采用上述特定单线组合成的导线应在订货时另加说明。本标准包括的各类钢芯耐热铝合金架空导线型号和名称见表1。
Thermal-resistant aluminum-alloy conductors, steel core reinforced for overhead transmission line
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号