K12 带绝缘层电线 标准查询与下载
共找到 1204 条与 带绝缘层电线 相关的标准，共 81 页
This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 155 with a dual coating. The underlying coating is based on polyurethane resin@ which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is a bonding layer based on a thermoplastic resin. NOTE A modified resin is a resin that has undergone a chemical change@ or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: ?C Grade 1B: 0@020 mm up to and including 0@800 mm; ?C Grade 2B: 0@020 mm up to and including 0@800 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013.
Specifications for particular types of winding wires - Part 35: Solderable polyurethane enamelled round copper wire, class 155, with a bonding layer
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-10
- 实施
- 2013-10-16
This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 240 with a sole coating of aromatic polyimide resin. The range of nominal conductor dimensions covered by this standard is: -width: min. 2@0 mm max. 16@0 mm; -thickness: min. 0@80 mm max. 5@60 mm. Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors. The specified combinations of width and thickness@ as well as the specified width/thickness ratio@ are given in IEC 60317-0-2.
Specifications for particular types of winding wires - Part 47: Aromatic polyimide enamelled rectangular copper wire, class 240
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-10
- 实施
- 2013-10-16
This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 180 with a dual coating. The underlying coating is based on polyesterimide resin@ which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is a bonding layer based on a thermoplastic resin. NOTE A modified resin is a resin that has undergone a chemical change@ or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this part is: ?C Grade 1B: 0@020 mm up to and including 1@600 mm; ?C Grade 2B: 0@020 mm up to and including 1@600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013.
Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-10
- 实施
- 2013-10-16
This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 155 with a dual coating. The underlying coating is based on polyurethane resin@ which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide resin. NOTE A modified resin is a resin that has undergone a chemical change@ or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: -Grade 1: 0@050 mm up to and including 1@600 mm; - Grade 2: 0@050 mm up to and including 1@600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013.
Specifications for particular types of winding wires - Part 21: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 155
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-10
- 实施
- 2013-10-12
This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 180 with a sole coating based on polyesterimide resin@ which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change@ or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is: -Grade 1: 0@020 mm up to and including 1@600 mm; -Grade 2: 0@020 mm up to and including 1@600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013.
Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-10
- 实施
- 2013-10-12
This International Standard specifies a test method detailing the tensile test procedures to be carried out on Ag/Bi-2223 and Ag/Bi-2212 superconductive composite wires at room temperature. This test is used to measure the modulus of elasticity and to determine the 0@2 % proof strength. When the 0@2 % proof strength could not be determined due to earlier failure@ the stress level at apparent strains of 0@05 %@ 0@1 %@ 0@15 %@ 0@2 %@ 0@25 % with increment of 0@05 % is measured. The values for elastic limit@ fracture strength@ percentage elongation after fracture and the fitted type of 0@2 % proof strength serve only as a reference (see Clauses A.4@ A.5@ A.6 and A.10). The sample covered by this test procedure should have a round or rectangular cross-section with an area of 0@3 mm2 to 2@0 mm2 (corresponding to the tape-shaped wires with width of 2@0 mm to 5@0 mm and thickness of 0@16 mm to 0@4 mm).
Superconductivity - Part 18: Mechanical properties measurement - Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors
- ICS
- 29.050
- CCS
- K12
- 发布
- 2013-09
- 实施
- 2013-09-14
Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminum wire
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-09
- 实施
- 2013-09-28
Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminum wire
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-09
- 实施
Winding wires - Test methods - Part 3: Mechanical properties
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-07
- 实施
Winding wires - Test methods - Part 3: Mechanical properties
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-07
- 实施
- 2013-08-03
Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155 (IEC 60317-48:2012); German version EN 60317-48:2012
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 61: Polyester glass fibre wound, minimum class 180, resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 180 (IEC 60317-61:2012); German version EN 60317-61:
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 (IEC 60317-62:2012); German version EN 60317-62:2
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 49: Glass-fibre wound high temperature resin or varnish impregnated, bare or enamelled round copper wire, temperature index 180 (IEC 60317-49:2012 + Cor. :2013); German version EN 60317-49:2012
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 0-8: General requirements - Polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-8:2012); German version EN 60317-0
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
DIN EN 60317-50:2013 特种绕组线规格.第50部分:温度指数200玻璃丝绕包树脂或漆浸渍裸或漆包圆铜线(IEC 60317-50-2012).德文版本EN 60317-50-2012
Specifications for particular types of winding wires - Part 50: Glass-fibre wound silicone resin or varnish impregnated, bare or enamelled round copper wire, temperature index 200 (IEC 60317-50:2012); German version EN 60317-50:2012
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 2: Solderable polyurethane enamelled round copper wire, class 130, with a bonding layer (IEC 60317-2:2012); German version EN 60317-2:2012
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-06
- 实施
- 2013-06-01
Specifications for particular types of winding wires - Part 60: Polyester glass fibre wound minimum class 155 resin or varnish impregnated or not impregnated, bare or enamelled, rectangular copper wire, temperature index 155 (IEC 60317-60:2012); German ve
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-04
- 实施
- 2013-04-01
Winding wires - Test methods - Part 6: Thermal properties (IEC 60851-6:2012); German version EN 60851-6:2012
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-03
- 实施
Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180 (IEC 60317-56:2012); German version EN
- ICS
- 29.060.10
- CCS
- K12
- 发布
- 2013-03
- 实施
- 2013-03-01
