K60 电气设备与器具综合 标准查询与下载

IEC 61496-1:1997 机械的安全 电敏保护设备 第1部分:一般要求和试验

Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests

JB/T 8458-1996 电气设备辅件塑料制品.一般要求和试验方法

本标准规定了电气设备辅件塑料制品的一半要求和试验方法。 本标准适用于成套开关设备、电控设备及其它电气设备中属于辅件范围的所有塑料制品。对于其它场所使用的制品，由用户与制造厂协商决定。

Auxiliary plastic products of electrical equipments General requirements and test method

BS EN 61229:1996 交流设备带电作业用刚性保护罩

This standard does not include barriers having dielectric withstand which depends on the positioning clearance.

Rigid protective covers for live working on a.c. installations

IEC 61800-3:1996 可调速电力传动系统 第3部分:包括特定试验方法的电磁兼容(EMC)产品标准

Adjustable speed electrical power drive systems - Part 3: EMC product standard including specific test methods

DLA AN3105 REV 4 NOTICE 1-1996 接地端

AN3105, dated 27 July 1993, and any subsequent revisions or change notices are inactive for new design and shall be no longer used as a guidance reference for new designs.

TERMINAL-GROUND

IEC 61084-2-4:1996 电气装置用电缆槽和管道系统 第2部分:特殊要求 第4节:接线柱

Specifies requirements for service poles intended for the accomodation, and where necessary for the segregation, of conductors, cables or cords and/or other electrical equipment in electrical installations.

Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 4: Service poles

IEC 61491:1995 工业机械电气设备.控制器和装置间实时通信用串行数据传输线

Electrical equipment of industrial machines - Serial data link for real-time communication between controls and drives

BS EN 50102:1995 防止电气设备受外部机械冲击(IK代码)的外壳保护度

A classification system to promote a uniform method for determining the various degrees of protection and describes the tests to prove the various degrees of protection.

Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

BS 7822-1:1995 低压系统内设备的绝缘配合.第1部分:原则、要求和试验

Specifies the requirements for clearances, creepage distances and solid insulation for equipment based upon their performance criteria.

Insulation coordination for equipment within low-voltage systems - Principles, requirements and tests

DIN VDE 0100-732:1995 额定电压最高可达 1 kV 的电力设备安装.第732部分:公共电缆网建筑物的电缆入口

Erection of power installations with nominal voltages up to 1000 V - Part 732: Cables entries into buildings in public cable networks

SANS 61010-2-031:1993 测量，控制和实验室用电气设备的安全性要求．第2．031部分：电气测量和试验用手持式探针组件的安全要求

Applies to hand-held and hand-manipulated probe assemblies and related accessories for use in the interface between an electrical phenomenon and a measuring or test instrument. They may be stand-alone probe assemblies or accessories to other equipment.

Safety requirements for electrical equipment for measurement, control, and laboratory use Part 2-031: Particular requirements for hand-held probe assemblies for electrical measurement and test

CSA IEC E1241-1-1-95-CAN/CSA:1995 专门用于在可燃灰尘环境下的电器设备-第1部分:外罩保护电器设备-分段1:设备的要求通用指令 第1号

L’Association canadienne de normalisation (CSA), sous les auspices de laquelle cette Norme nationale a été préparée, a rep ses lettres patentes en 191 9 et son accréditation au sein du Système de Normes nationales par le Conseil canadien des normes en

Electrical Appliance Specially used for Flammable Dust Atmosphere-Part 1: Electrical Appliance for the Protection of Envelopes-Subsection 1: Requirements for Equipment General Instruction No 1

SANS 60136:1986 电动设备用电刷和电刷支架的尺寸

Applies to brushes and brush-holders for electrical machinery. It applies only to brushes and brush-holders for cylindrical commutators and slip rings.

Dimensions of brushes and brush-holders for electrical machinery

EN 60010-2-02:1994 测量、控制和实验室用电气设备的安全性要求.第u320部分:实验室离心机的详细要求(包括修改件A1-1996)

This clause of Part 1 is applicable except as follows: 1.1 Scope Replacement: This Part 2 ?S applicable to electrically powered LABORATORY CENTRIFUGES. 1.1 .l Aspects 8xCluded from SWpê Addition: - which are flammable or explosive (see 5.4.101); - that chemically react vigorously (see 5.4.101); additional precautions which may need to be observed when centrifuging materials additional precautions which may need to be observed when centrifuging materials II 1 .í .2 Equipment excluded from scope Addition: - rotating electrical machinery within the scope of IEC 34; II - CENTRIFUGES (used in explosive atmospheres). 1.2 Objec? Addition: - contact with moving parts (see 7.2); - CENTRIFUGE mOVem0fi during any DISRUPTION (See 7.3.101); - expelled parts (see 7.5); - 7.5.1 04); - - small particles from ROTOR ASEMBUES, expelled in air exhaust systems (see high energy chemical reaction after ROTOR DISRUPTION (see 7.5.1 05); ineffectiveness of BIOSEALS (see 13.101).

Safety requirements for electrical equipment for measurement, control and laboratory use Part u320 Particular rqyirernents for laboratory centrifuges (includes amendment Al : 1996)

CSA SPE-2000-94-1994 在加拿大安装并使用电气设备的规范,通用指令第1号

This International Standard specifies the information to be obtained from the instruments on the instrument panel by the operator in his normal position. it also specifies the arrangement and colour distinction of this instrumentation in order to make

Guide for Electrical Equipment for Installation and Use in Canada General Instruction No 1

IEC 61293:1994 电气设备电源额定值的标记 安全要求

Establishes minimum requirements and general rules on marking electrical equipment with ratings and other characteristics to enable the proper and safe selection and installation of electrical equipment related to any supply of electricity. The object is

Marking of electrical equipment with ratings related to electrical supply - Safety requirements

ANSI/ISA S82.01-1994 电气和电子试验、测量、控制和有关的设备.一般要求

Applies to electrical and electronic test, measuring, controlling, and related equipment. This standard applies to equipment that is rated for connection to supply circuits that exceed extra-low voltage and that do not exceed 480 volts rms, between phases for three-phase supply circuits or 250 volts rms, single phase, or dc.

Electric and Electronic Test, Measuring, Controlling, and Related Equipment: General Requirements

SJ/T 9167.7-1993 电气设备用双重绝缘系统

1.1 本标准适用于以电源线--插头进行电气连接的，标有"双重绝缘"的，其额定电压不超过250V的电气设备。这类设备按照"国家电气法规"的规定，用在对地电位不超过150V的供电支路中。 1.2 标有"双重绝缘"的设备，应遵守本标准以及用于特定类型设备--终端产品的标准的有关要求。 如果终端产品标准含有对双重绝缘的要求，则该标准要放在首位。

Double insulation systems for use in electrical equipment

JB/T 7081-1993 电工专用试验仪器设备型号编制方法

本标准规定了电工专用试验仪器设备的型号编制方法。 本标准适用于电子学、电工学方法测量电学量和其他参量的电工专用试验仪器设备。

Model designation method for testing instruments and apparatus

JB/T 7080-1993 绕组匝间冲击电压试验仪

本标准规定了绕组匝间冲击电压试验仪的技术要求，试验方法及检验规则等。 本标准适用于额定输出峰值电压5kV、15kV、40kV，满足JB/Z 293交流高压电机定子绕组匝间绝缘试验规范，JB/Z 294交流低压电机散嵌绕组匝间绝缘试验方法规定的匝间试验仪。

Testing instrument for winding inter-turn impulse voltage