L05 可靠性和可维护性 标准查询与下载

IEC 60300-3-1:1991 可靠性管理.第3部分:应用指南.第1节:可靠性技术分析:方法学指南

Dependability management; part 3: application guide; section 1: analysis techniques for dependability: guide on methodology

IEC 61078:1991 可靠性分析技术 - 可靠性方框图法

Analysis techniques for dependability; reliability block diagram method

DIN 40041:1990 可信性.概念

This standard is intended to standardize the terms and definitions in the field of depentability and will be a help for understanding in this area.

Dependability; concepts

IEC 60706-2:1990 设备维修性指南 第2部分:第5节:设计阶段的维修性分析

Describes maintainability studies and their relationships to other maintainability and maintainance support tasks given in the other sections of the guide.

Guide on maintainability of equipment; part 2: section five; maintainability studies during the design phase

IEC 61014:1989 可靠性增长大纲

Programmes for reliability growth

IEC 60605-4/AMD1:1989 设备可靠性试验.第4部分:设备可靠性测定试验的确定点估计和置信极限的规程.第1次修改

Equipment reliability testing; part 4: procedures for determining point estimates and confidence limits for equipment reliability determination tests; amendment 1 to IEC 60605-4:1986

IEC 60605-6/AMD1:1989 第1次修改

Equipment reliability testing; part 6: tests for the validity of a constant failure rate assumption; amendment 1 to publication 605-6:1986

JEDEC JEP114-1989 微粒冲击噪音检测(PIND)试验、操作者培训和认证指南

The STU sensor is approximately 1" in diameter. The data was taken with the STU centered and then moved incrementally until the outer edge of the STU transducer was even with the a outer edge of the transducer platform.

Guidelines for Particle Impact Noise Detection (PIND) Testing, Operator Training and Certification

EIA IS-32-1989 使用可变测试数据PPM中质量水平的评定.有效日期.勘误:1990年4月19日

The traditional approach to measuring levels of nonconformance using attribute data, whether the results are stated in percent or Parts Per Million (PPM), becomes more burdensome as the nonconformance levels approach zero. The quantities required to establish a data base for an acceptable confidence level may be in the hundreds of thousands, which also makes it virtually impossible for a user to verify these quality levels at an incoming inspection facility.

Assessment of Quality Levels in PPM Using Variables Test Data Errata 4/19/1990

SJ 2907-1988 家用电子产品设计文件的成套、编制和更改

本标准规定了家用电子产品，如黑白电视接收机、彩色电视接收机、收音机、录音机、组合音响设备等产品设计文件的成套性要求，编制方法和更改规定，供编制设计文件时使用。与上述类似的电子产品编制设计文件时也可参照使用。

Completeness,preparation and revision of design documents for household electronic products

IEC 60706-3:1987 设备维修性指南 第3部分:第6和7节:数据的验证、收集、分析与报告

This guide is intended to make recommendations for the standardization of maintainability practices and to stimulate ideas in the maintainability field. Describes the various aspects of verification necessary to ensure that the specified requirements hav

Guide on maintainability of equipment. Part 3: Sections Six and Seven - Verification and collection, analysis and presentation of data.

HD 485 S1-1987 系统可靠性的分析技术.失效模式和效应分析(FMEA)的规程

Analysis techniques for system reliability; procedure for failure mode and effects analysis (FMEA)

IEC 60605-3-2:1986 设备可靠性试验 第3部分:推荐试验条件 第2节:固定使用在有气候防护场所的设备 精模拟

Contains preferred test conditions as referred to in sub-clause 8.4. of IEC Publication 605-1. Whenever possible, test cycles should be chosen from among those given in this or other sections of IEC Publication 605-3. Is applicable to equipment for stati

Equipment reliability testing. Part 3 : Preferred test conditions. Equipment for stationary use in weatherprotected locations - High degree of simulation

IEC 60605-4:1986 设备可靠性试验.第4部分:设备可靠性测定试验的确定点估计和置信极限的规程

Equipment reliability testing. Part 4 : Procedures for determining point estimates and confidence limits from equipment reliability determination tests

IEC 60605-6:1986 设备可靠性试验.第6部分:恒定失效率先决条件下的有效性试验

Equipment reliability testing. Part 6 : Tests for the validity of a constant failure rate assumption

IEC 60605-3-1:1986 设备可靠性试验 第3部分:推荐试验条件 第1节:室内便携设备 粗模拟

Contains preferred test conditions as referred to in sub-clause 8.4. of IEC Publication 605-1. Whenever possible, test cycles should be chosen from among those given in this or other sections of IEC Publication 605-3. Is applicable to indoor portable equ

Equipment reliability testing. Part 3 : Preferred test conditions. Indoor portable equipment - Low degree of simulation

IEC 60863:1986 可靠性、维修性和可用性预计的报告

Presentation of reliability, maintainability and availability predictions

IEC 60812:1985 系统可靠性分析技术 失效模式和效应分析(FMEA)程序

This standard describes Failure Mode and Effects Analysis (FMEA) and Failure Mode@ Effects and Criticality Analysis (FMECA)@ and gives guidance as to how they may be applied to achieve various objectives@ as follows:- by providing the procedural steps necessary to perform an analysis;- by identifying appropriate terms@ assumptions@ criticality measures@ failure modes;- by determining basic principles;- by providing examples of the necessary forms.All the general qualitative considerations presented for FMEA will apply to FMEAC@ since one is an extension of the other.

Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)

IEC 60605-1/AMD1:1982 设备可靠性试验 第1部分:一般要求 修改1

Equipment reliability testing. Part 1 : General requirements

IEC 60706-1:1982 设备维修性指南 第1部分:第1、2、3节:引言、要求、维修性大纲

The guide is intended to make recommendations for the standardization of maintainability practices, and to stimulate ideas in the maintainability field. Includes three sections of the guide on maintainability which concern with introduction to maintainab

Guide on maintainability of equipment. Part 1 : Sections One, Two and Three. Introduction, requirements and maintainability programs